Engineering Science and Materials Commons^™

Elastic Properties Of The Non-Mixing Copper Donor Assisted Material In Friction Stir Welding Of Aluminum Alloys Using Nanoindentation, M. Ojha, A. H. Al-Allaq, Y. S. Mohammed, S. N. Bhukya, Z. Wu, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Friction stir welding of high-strength materials such as steels is the impeded by the lack of the vast heat input needed to start the process. Contact friction is considered the most dominant source of heat generation for FSW steels which tends to cause severe wear conditions of the tool hear. To relieve the extreme wear conditions that occur on the tool heads because of FSW steels, we introduce the non-mixing Cu donor stir material to friction stir welding of aluminum alloys. The elastic properties of the Cu donor assisted friction stir welded aluminum alloys are measured using nanoindentation. The hardness …

Imparities Of Shear Avalanches Dynamic Evolution In A Metallic Glass, Yin Du, Qing Zhou, Qian Jia, Yidi Shi, Haifeng Wang, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

The imparities of shear avalanches dynamic evolution under nanoindentation originating from the soft regions and the stiff matrix were explored in a metallic glass by statistical and dynamic analysis. Upon the continuous indentation process, the dynamic state of the stiff matrix exhibits a transition from a chaotic behavior to a self-organized critical (SOC) behavior, whereas the soft regions are domi-nated by the SOC behavior throughout the indentation process. The mechanism was clarified by the evolution of the cut-off size of shear avalanches. These findings might advance our fundamental understanding of inhomogeneous deformation on microscale.

IMPACT STATEMENT The shear avalanches dynamic …

In Situ Mechanical Characterization Of The Mixed- Mode Fracture Strength Of The Cu/Si Interface For Tsv Structures, Chenglin Wu, Congjie Wei, Yanxiao Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In situ nanoindentation experiments have been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiments in the characterization of nonlinear material properties of 3D integrated microelectronic devices using the through-silicon via (TSV) technique. The elastic, plastic, and interfacial fracture behavior of the copper via and matrix via interface were characterized using small-scale specimens prepared with a focused ion beam (FIB) and nanoindentation experiments. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7° to 83.7°. The mixed-mode fracture strengths were extracted …

Mechanical Characterizations Of 3d-Printed Plla/Steel Particle Composites, Hozhabr Mozafari, Pengfei Dong, Haitham Hadidi, Michael P. Sealy, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to characterize the micromechanical properties of poly-L-lactic acid (PLLA) composites reinforced by grade 420 stainless steel (SS) particles with a specific focus on the interphase properties. The specimens were manufactured using 3D printing techniques due to its many benefits, including high accuracy, cost effectiveness and customized geometry. The adopted fused filament fabrication resulted in a thin interphase layer with an average thickness of 3 μm. The mechanical properties of each phase, as well as the interphase, were characterized by nanoindentation tests. The effect of matrix degradation, i.e., imperfect bonding, on the elastic modulus of …

Artificial Neural Network And Finite Element Modeling Of Nanoindentation Tests On Silica, Kianoosh Koocheki

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Two major forms of Silica include the crystalline form named Quartz which consist of the sand grains in nature, and amorphous form named Silica Glass or Fused Silica which is commonly known as glass. Fused Silica is an amorphous crystal that can show plastic behavior at micro-scale despite its brittle behavior in large scales. Due to the amorphous and ductile nature of Fused Silica, this behavior may not be explained well using the traditional dislocation-based mechanism of plasticity for crystalline solids. The crystal plasticity happens due to shear stress and stored energy in the material as dislocations which does not …