Engineering Science and Materials Commons^™

Multi-Axial Failure Of High-Performance Fiber During Transverse Impact, Matthew C. Hudspeth

Open Access Dissertations

The effect of projectile nose geometry on ensuing wave development in high-performance yarns is explored during single yarn transverse impact. Special attention has been placed on visualizing the immediate region around the projectile-yarn contact site for 0.30-cal round, 0.30-cal fragment simulation projectiles (FSP), and razor blades using high-speed imaging. Kevlar® KM2, Dyneema®SK76 and AuTx have been impacted at velocities ranging from ∼100 m/s to ∼1200 m/s depending on projectile nose shape, with an emphasis set on determining the critical velocity wherein below said velocity significant development of wave propagation occurs and above said velocity the yarn fails immediately upon impact. …

Analytical Investigation Of Fretting Wear With Special Emphasis On Stress Based Models, Arnab Jyoti Ghosh

Open Access Dissertations

Fretting refers to the minute oscillatory motion between two surfaces in contact under an applied normal load. It can cause either surface or subsurface initiated failure resulting in either fatigue or wear or both. Two distinct regimes – partial slip and gross slip are typically observed in fretting contacts. Due to the nature of contact, various factors such as wear debris, oxidation, surface roughness, humidity etc. effect failures caused due to fretting. A number of different techniques have been developed to quantify fretting damage and several numerical models are proposed to predict damage due to fretting. Fretting wear also depends …

Detailed Finite Element Analysis And Preliminary Study Of The Effects Of Friction And Fastener Pre-Tension On The Mechanical Behavior Of Fastened Built-Up Members, Francisco Javier Bonachera Martin

Open Access Theses

The characterization of fatigue resistance is one of the main concerns in structural engineering, a concern that is particularly important in the evaluation of existing bridge members designed or erected before the development of fatigue design provisions. The ability of a structural member to develop alternate load paths after the failure of a component is known as member-level or internal redundancy. In fastened built-up members, these alternate load paths are affected by the combination of fastener pre-tension and friction between the structural member components in contact. In this study, a finite element methodology to model and analyze riveted and bolted …

Design And Assembly Of Nanostructured Complex Metal Oxide Materials For The Construction Of Batteries And Thermoelectric Devices, Gautam Ganapati Yadav

Open Access Dissertations

Thermoelectric devices and lithium-ion batteries are among the fastest growing energy technologies. Thermoelectric devices generate energy from waste heat, whereas lithium-ion batteries store energy for use in commercial applications. Two different topics are bound with a common thread in this thesis - nanotechnology! In fact, nanostructuring is a more preferred term for the approach I have taken herein. Another commonality between these two topics is the material system I have used to prove my hypotheses - complex metal oxides.

Complex metal oxides can be used for both energy generation and storage as they are stable at high temperatures, are benign …

Fabricating Complex-Shaped Components By Room-Temperature Injection Molding Of Aqueous Ceramic Suspension Gels, Valerie Lynn Wiesner

Open Access Dissertations

Water-based ceramic suspension gels (CeraSGels) effectively produced dense, near-net shape ceramic parts by room-temperature injection molding, a novel processing method based on traditional ceramic injection molding. This alternative method eliminated the need for heating and cooling feedstocks to process, as is required in conventional injection molding, through control of the rheological response of the CeraSGels by simply varying polymer content without the use of any harsh crosslinking or curing agents or further chemical processes. The development of room-temperature injection molding initially focused on forming CeraSGels based on alumina, a readily available model material, in order to optimize suspension preparation and …

Preparation Of Mesoporous Silica Supported Ruthenium Oxides And The Application And Kinetic Study In The Catalysis Of Water Oxidation, Yang Zhang

Open Access Dissertations

Photo-induced water splitting of water into H2 and O2 has been a major focus in the development of clean and renewable energy. The development of viable and efficient catalysts that facilitates O2 production remains the major challenge in the study of the corresponding half-reaction of water oxidation. There are plenty of metal oxides reported active in the catalysis of water oxidation. However, several important performance bench marks of those materials, such as the non-stoichiometric production of O2, slow reaction rate and/or low quantum efficiency, remain to be improved.

Ruthenium oxide (RuO2) has long been known as one of the most …

Analysis Of An Actuated Two Segment Leg Model Of Locomotion, Nikhil Vinayak Rao

Open Access Theses

Research studies on dynamic models of legged locomotion have generally focused on telescoping-type leg models. Such telescoping spring loaded inverted pendulum (SLIP) models have been able to accurately predict observed center of mass (CoM) trajectories. There have been comparatively fewer studies on dynamics of locomotion

with segmented legs. Some earlier studies on the dynamics due to leg segmentation appear straightforward. For example, a simple model with the only joint moment being due to a passive springy knee has been shown to behave similarly to a telescoping spring-mass model. However, in real-life animal locomotion, there are multiple joint-moments acting at the …

Orientation Controllable Epitaxial Vapor-Liquid-Solid Semiconductor Nanowire Synthesis On Silicon Substrate, Sung Hwan Chung

Open Access Dissertations

Semiconductor nanowires synthesized via the vapor-liquid-solid (VLS) mechanism have attracted extensive research interest in recent years owing to their unique structure as a promising candidate for the future electronic devices. Germanium and silicon nanowires, in particular, are compatible with the current silicon-based technology via direct assembly. However, one of the main challenges for the successful nanowire application in large-scale is the lack of the method for obtaining nanowires in desired positions and directions. Therefore, the comprehensive, systematic understanding of epitaxial nanowire growth and the more suitable method to align nanowires on novel structure are required. In this work, the synthesis …