Computer Engineering Commons^™

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Quantum Computing And Resilient Design Perspectives For Cybersecurity Of Feedback Systems, Keshav Kasturi Rangan, Jihan Abou Halloun, Henrique Oyama, Samantha Cherney, Ilham Azali Assoumani, Nazir Jairazbhoy, Helen Durand, Simon Ka Ng

Chemical Engineering and Materials Science Faculty Research Publications

Cybersecurity of control systems is an important issue in next-generation manufac- turing that can impact both operational objectives (safety and performance) as well as process designs (via hazard analysis). Cyberattacks differ from faults in that they can be coordinated efforts to exploit system vulnerabilities to create otherwise unlikely hazard scenarios. Because coordination and targeted process manipulation can be characteristics of attacks, some of the tactics previously analyzed in our group from a control system cybersecurity perspective have incorporated randomness to attempt to thwart attacks. The underlying assumption for the generation of this randomness has been that it can be achieved …

Live Access Control Policy Error Detection Through Hardware, Bryce Mendenhall

Graduate Theses and Dissertations

Access Control (AC) is a widely used security measure designed to protect resources and infrastructure in an information system. The integrity of the AC policy is crucial to the protection of the system. Errors within an AC policy may cause many vulnerabilities such as information leaks, information loss, and malicious activities. Thus, such errors must be detected and promptly fixed. However, current AC error detection models do not allow for real-time error detection, nor do they provide the source of errors. This thesis presents a live error detection model called LogicDetect which utilizes emulated Boolean digital logic circuits to provide …

A Machine Learning Approach To Intended Motion Prediction For Upper Extremity Exoskeletons, Justin Berdell

Graduate Research Theses & Dissertations

A fully solid-state, software-defined, one-handed, handle-type control device built around a machine-learning (ML) model that provides intuitive and simultaneous control in position and orientation each in a full three degrees-of-freedom (DOF) is proposed in this paper. The device, referred to as the “Smart Handle”, and it is compact, lightweight, and only reliant on low-cost and readily available sensors and materials for construction. Mobility chairs for persons with motor difficulties could make use of a control device that can learn to recognize arbitrary inputs as control commands. Upper-extremity exoskeletons used in occupational settings and rehabilitation require a natural control device like …

On The Impact Of Gravity Compensation On Reinforcement Learning In Goal-Reaching Tasks For Robotic Manipulators, Jonathan Fugal, Hasan A. Poonawala, Jihye Bae

Electrical and Computer Engineering Faculty Publications

Advances in machine learning technologies in recent years have facilitated developments in autonomous robotic systems. Designing these autonomous systems typically requires manually specified models of the robotic system and world when using classical control-based strategies, or time consuming and computationally expensive data-driven training when using learning-based strategies. Combination of classical control and learning-based strategies may mitigate both requirements. However, the performance of the combined control system is not obvious given that there are two separate controllers. This paper focuses on one such combination, which uses gravity-compensation together with reinforcement learning (RL). We present a study of the effects of gravity …

Control Synthesis For Parametric Timed Automata Under Reachability, Ebru Aydin Göl

Turkish Journal of Electrical Engineering and Computer Sciences

Timed automata is a fundamental modeling formalism for real-time systems. During the design of such real-time systems, often the system information is incomplete, and design choices can vary. These uncertainties can be integrated to the model via parameters and labelled transitions. Then, the design can be completed by tuning the parameters and restricting the transitions via controller synthesis. These problems, namely parameter synthesis and controller synthesis, are studied separately in the literature. Herein, these are combined to generate an automaton satisfying the given specification by both parameter tuning and controller synthesis, thus exploring all design choices. First, it is shown …

Lawn Buddy, Jayson Johnston, Andrew Brown, Jacob Maljian

Electrical Engineering

Grass lawns are a common hallmark of the American home. In 2019, a survey from the National Association of Landscape Professionals found that 81% of all Americans owned a lawn [1]. Mowing is a time consuming and costly chore that is part of maintaining a grass lawn. The manual labor in mowing a lawn can exceed 40 hours per year [2]. People commonly incur weekly costs on mowing services to save time. Traditional gas powered mowers are physically demanding and use engines that need routine maintenance. They operate loudly enough that users should be wearing hearing protection and the noise …

Evaluating Driving Performance Of A Novel Behavior Planning Model On Connected Autonomous Vehicles, Keyur Shah

Honors Scholar Theses

Many current algorithms and approaches in autonomous driving attempt to solve the "trajectory generation" or "trajectory following” problems: given a target behavior (e.g. stay in the current lane at the speed limit or change lane), what trajectory should the vehicle follow, and what inputs should the driving agent apply to the throttle and brake to achieve this trajectory? In this work, we instead focus on the “behavior planning” problem—specifically, should an autonomous vehicle change lane or keep lane given the current state of the system?

In addition, current theory mainly focuses on single-vehicle systems, where vehicles do not communicate with …

An Application Of Sliding Mode Control To Model-Based Reinforcement Learning, Aaron Thomas Parisi

Master's Theses

The state-of-art model-free reinforcement learning algorithms can generate admissible controls for complicated systems with no prior knowledge of the system dynamics, so long as sufficient (oftentimes millions) of samples are available from the environ- ment. On the other hand, model-based reinforcement learning approaches seek to leverage known optimal or robust control to reinforcement learning tasks by mod- elling the system dynamics and applying well established control algorithms to the system model. Sliding-mode controllers are robust to system disturbance and modelling errors, and have been widely used for high-order nonlinear system control. This thesis studies the application of sliding mode control …

Desarrollo De Una Estrategia De Control Predictivo Aplicado A Un Péndulo Invertido, Que Permita La Estabilización De Imágenes En Robots Para Exploración Agrícola, David Mateo Rojas Vallejo

Ingeniería en Automatización

La robótica es un campo de estudio tan amplio, que se puede extender prácticamente a cualquiera de las labores humanas; una de estas actividades es la agricultura, aunque para que esto se logre, primero se deben considerar factores mas específicos de un sistema robótico como: visión artificial, estructuras robóticas, control de sistemas, entre otros. En este proyecto se desarrolla una estrategia de control para una plataforma de péndulo invertido, que emula el sistema mecánico en donde se posicionaría la cámara de un robot agrícola. El sistema consiste en un péndulo invertido rotativo, y la estrategia de control que se implementó …

Cyber-Physical Embedded Systems With Transient Supervisory Command And Control: A Framework For Validating Safety Response In Automated Collision Avoidance Systems, Daniel K. Trembley

Graduate Dissertations and Theses

The ability to design and engineer complex and dynamical Cyber-Physical Systems (CPS) requires a systematic view that requires a definition of level of automation intent for the system. Since CPS covers a diverse range of systemized implementations of smart and intelligent technologies networked within a system of systems (SoS), the terms “smart” and “intelligent” is frequently used in describing systems that perform complex operations with a reduced need of a human-agent. The difference between this research and most papers in publication on CPS is that most other research focuses on the performance of the CPS rather than on the correctness …

Performance Comparison Of The Notable Acceleration- And Angle-Based Guidance Laws For A Short-Range Air-To-Surface Missile, Bülent Özkan, Mustafa Kemal Özgören, Gökmen Mahmutyazicioğlu

Turkish Journal of Electrical Engineering and Computer Sciences

Short-range air-to-surface missiles have become globally popular in the last two decades. As a performance driver, the type of guidance law gains importance. In this study, proportional navigation, velocity pursuit, and augmented proportional navigation guidance laws, whose resulting guidance commands take the form of lateral acceleration, are applied to a short-range air-to-surface missile against both stationary and maneuvering ground targets. Body pursuit and linear homing guidance laws, which yield angular commands, are additionally applied. Having completed the relevant computer simulations, we conclude that none of the acceleration- and angle-based guidance laws are absolutely superior to the others.

Ubot-7: The Design Of A Compliant Dexterous Mobile Manipulator, Jonathan Cummings

Masters Theses

This thesis presents the design of uBot-7, the latest version of a dexterous mobile manipulator. This platform has been iteratively developed to realize a high performance-to-cost dexterous whole body manipulator with respect to mobile manipulation. The semi-anthropomorphic design of the uBot is a demonstrated and functional research platform for developing advanced autonomous perception, manipulation, and mobility tasks. The goal of this work is to improve the uBot’s ability to sense and interact with its environment in order to increase the platforms capability to operate dexterously, through the incorporation of joint torque feedback, and safely, through the implementation of passive and …

Interpreting, Stephanie Jo Kent

Doctoral Dissertations

What do community interpreting for the Deaf in western societies, conference interpreting for the European Parliament, and language brokering in international management have in common? Academic research and professional training have historically emphasized the linguistic and cognitive challenges of interpreting, neglecting or ignoring the social aspects that structure communication. All forms of interpreting are inherently social; they involve relationships among at least three people and two languages. The contexts explored here, American Sign Language/English interpreting and spoken language interpreting within the European Parliament, show that simultaneous interpreting involves attitudes, norms and values about intercultural communication that overemphasize information and discount …

Modeling, Analysis, And Control Of A Mobile Robot For In Vivo Fluoroscopy Of Human Joints During Natural Movements, Matthew A. Young

Doctoral Dissertations

In this dissertation, the modeling, analysis and control of a multi-degree of freedom (mdof) robotic fluoroscope was investigated. A prototype robotic fluoroscope exists, and consists of a 3 dof mobile platform with two 2 dof Cartesian manipulators mounted symmetrically on opposite sides of the platform. One Cartesian manipulator positions the x-ray generator and the other Cartesian manipulator positions the x-ray imaging device. The robotic fluoroscope is used to x-ray skeletal joints of interest of human subjects performing natural movement activities. In order to collect the data, the Cartesian manipulators must keep the x-ray generation and imaging devices accurately aligned while …

Design And Realization Of A Welding Oscillator, Muci̇z Özcan

Turkish Journal of Electrical Engineering and Computer Sciences

Welding is one of the most popular methods to combine metal pieces in manufacturing processes. Arc welding, among all welding techniques, is the most commonly used in manufacturing due to its cost and flexibility. During the manufacturing process, arc welding is either performed by an operator or by automatic tools such as welding oscillators. Using automatic tools has advantages over manual use, as the process will be faster, cheaper, and have less welding flaws. In this paper, a homemade welding oscillator and the method to manufacture it are presented. The presented welding oscillator can be manufactured for a very low …

Kreative Outlets, Travis Crist, Steve Clark, Jason Peressini

Computer Engineering

With the widespread use of smart phones and the advancement of WiFi technologies, people now have the Internet at their fingertips at all times. Home automation and control has the possibility of becoming the next big technology that can utilize the abundant availability of the Internet. This paper documents the findings and results of a project aimed at developing the infrastructure needed for a home automation system that is accessible anywhere. We implemented a system that utilized a web enabled ethernet connection and RF wireless technology to control AC outlets and provide the user with feedback information about the status …

Design, Modeling And Control Strategy Of Pv/Fc Hybrid Power System, Dr. Adel A. Elbaset

Dr. Adel A. Elbaset

This paper describes development of a general methodology of an autonomous PV/FC system composed of photovoltaic (PV), electrolyzer, hydrogen storage tank and fuel cell (FC). The aim of this paper is to determine optimum design, control strategy, economic and performance of a PV/FC hybrid power generation system without battery storage taking into account all losses in the system. The paper also presents a computer program based on Matlab software to determine optimum design, control strategy, economic and performance of an autonomous PV/FC hybrid power generation system. The computer program develops to size system components in order to match the load …

A Case Study In Forensic Analysis Of Control, Fred Cohen

Journal of Digital Forensics, Security and Law

This paper describes a case study in which a method for forensic analysis of control was applied to resolve probative technical issues in a legal action. It describes one instance in which the analysis was successfully applied without challenge, addresses the details of most of the different facets of the analysis method, and demonstrates how such analysis provides a systematic approach to using technical methods to address legal issues as a case study.

An Electro-Oculogram Based System For Communication And Control Using Target Position Variation, Ronan Fitzmaurice, Ted Burke, Annraoi De Paor

Conference Papers

In this paper we describe a novel mode of human computer interaction based on gaze tracking using the electro-oculogram (EOG). Despite the relative simplicity of recording this signal, it is often discounted as a reliable method of gaze tracking because of problems arising from changing sensitivity and DC drift. We describe an original technique, Target Position Variation (TPV), which addresses this issue by presenting moving icons which, when followed with the eye, create a corresponding pattern in the EOG signal which can be used to infer the correct gaze position and to compensate for variations in sensitivity.