Structural Engineering Commons^™

Natural Gas Induced Vegetation Stress Identification And Discrimination From Hyperspectral Imaging For Pipeline Leakage Detection, Pengfei Ma, Ying Zhuo, Genda Chen, Joel G. Burken

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Remote Sensing Detection of Natural Gas Leaks Remains Challenging When using Ground Vegetation Stress to Detect Underground Pipeline Leaks. Other Natural Stressors May Co-Present and Complicate Gas Leak Detection. This Study Explores the Feasibility of Identifying and Distinguishing Gas-Induced Stress from Other Natural Stresses by Analyzing the Hyperspectral Reflectance of Vegetation. the Effectiveness of This Discrimination is Assessed Across Three Distinct Spectral Ranges (VNIR, SWIR, and Full Spectra). Greenhouse Experiments Subjected Three Plant Species to Controlled Environmental Stressors, Including Gas Leakage, Salinity Impact, Heavy-Metal Contamination, and Drought Exposure. Spectral Curves Obtained from the Experiments Underwent Preprocessing Techniques Such as Standard …

Characterization Of Alkali-Silica Reaction (Asr) Products And C-S-H Using Swir Spectroscopy For Nondestructive Detection Of Asr, Pengfei Ma, Wenyu Liao, Ying Zhuo, Hongyan Ma, Yanping Zhu, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study explores the feasibility of characterizing alkali-silica reaction (ASR) products and calcium silicate hydrates (C-S-H) from short-wave infrared (SWIR) spectroscopy. ASR products and C-S-H samples with different Ca/Si ratios were synthesized and analyzed through XRD, 29Si nuclei magnetic resonance (NMR) and SWIR spectroscopy. Fourier-transform infrared spectroscopy (FTIR) was collected to help interpret the results from the SWIR spectroscopy. The obtained spectroscopic features were applied to quantify the ASR product abundance denoted by the length expansion of mortar bars after an accelerated ASR test. The results show that the SWIR spectra of the synthetic ASR gels are similar regardless of …

Barriers To Use Of Cross-Laminated Timber In Maine, Shane R. O'Neill

Forest Resources Faculty Scholarship

To increase understanding of both the adoption rate and in-state manufacturing of mass timber In Maine, the 131^st Legislature and Governor Mills passed LD 881, a resolve directing a study of the barriers facing cross-laminated timber In Maine and provide recommendations to promote their use in construction. This study was developed in response to the resolve. The study engaged 108 unique participants to define available training, education, and experiences across the stakeholders throughout the building lifecycle process in the state.

From this information, the following five recommendations are proposed:

1. Understand the policies and initiatives of other states to develop …

International Information Management And Bim Best Practice Report, Ted Mckenna, Davitt Lamon

Reports

In order to inform the Digital Leadership and Cultural Change pillar of the Build Digital, a study of international best practice in digital adoption within the built environment sector globally was undertaken and is presented here-in. In order to identify key learnings for Ireland in the context of digital transformation, eight countries were included in this study, namely, Denmark, Finland, Netherlands, Germany, United Kingdom (UK), New Zealand, Australia and Singapore. These countries were selected for various reasons, including the level of digital maturity, the scale of the built environment sector and geographic spread. Key data for each country is included …

Sustainability And Circular Economy Horizon Scan And Needs Analysis, Sadaf Dalirazar, Mark Kelly, Derek Sinnott, James O'Donnell

Reports

The construction industry plays a crucial role in addressing the climate crisis as it is the largest global consumer of raw materials and contributes significantly to global energy consumption and emissions. Considering the world’s continuous population growth and the imperative to address infrastructure and housing demands the construction sector needs to adopt further sustainable strategies in its activities to reduce the pressure on natural resources. In addition, the Architecture, Engineering, and Construction (AEC) sector is responsible for generating substantial amount of waste known as Construction and Demolition Waste (CDW), which is projected to increase due to the future construction developments. …

Information Management And Bim Standards And Supports Inventory, Ryan Dempsey, Barry Mcauley, David Burke

Tools

The Digital Standards pillar consists of industry experts who champion the benefits of common rules, guidelines, and workflows that facilitate the improvement of information flow and information management across asset life cycles. Digital standards provide a common language that can be translated to technical specifications enabling clients, designers, contractors, and facilities managers, irrespective of their preferred tools, to communicate efficiently and reduce cost, rework, and disputes. Working closely with the Digital Procurement and Digital Education and Training pillars, this pillar is developing and delivering Irish Information Management/BIM (Digital Construction) guidelines for the sector.

This report summarises existing digital construction standards, …

Digital Construction Annual Survey 2022 Report, Davitt Lamon, Ted Mckenna

Reports

The Annual Survey 2022 was conducted to assess the state of digital transformation in the Irish construction and built environment sector. This report presents the analysis of survey data, with a focus on implications for the Build Digital project and Build Digital’s five pillars: Digital Leadership & Cultural Change, Digital Standards, Digital Education & Training, Digital Procurement, and Sustainability & Circular Economy. Key findings from the survey indicated that a significant number of organisations have started their digital transformation journey, with many identifying themselves as proactive and possessing a clear business-focused strategy. However, a considerable cohort of respondents are keen …

Effect Of Type And Quantity Of Inherent Alkali Cations On Alkali-Silica Reaction, Pengfei Ma, Jiaoli Li, Jincheng Bai, Ying Zhuo, Lingyu Chi, Yanping Zhu, Zhenhua Shi, Hongyan Ma, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, the macroscopical expansion induced by alkali-silica reaction (ASR) and its corresponding ASR products are investigated using ordinary Portland cement (OPC) mortar specimens with a gradient of boosted alkalis. Experimental results show that the expansion increases with the concentration of inherent alkalis. Sodium-boosted samples expand approximately three times as much as potassium-boosted samples. ASR gels that are present in aggregate veins are calcium-free and amorphous; the atomic ratios of ASR gels are nearly independent of the type and quantity of alkali cations. Aggregate ASR gel exudation occurs in high (≥2.5 %) sodium cases and produces potential Na-shlykovite. Crystalline …

An Investigation Into Ireland’S Bim Skills Gap, Guadalupe Centanni, Barry Mcauley

Conference Papers

The adoption of digital skills within the Irish AEC Sector has the potential to enhance efficiency and competitiveness among its stakeholders. Despite this opportunity, there is still a high demand for skilled BIM professionals, which cannot be currently met. To meet this skills demand and directly target future skills gaps within Ireland, several challenges must be addressed to facilitate broader BIM adoption. This paper focuses on addressing this gap by identifying steps to be followed to develop skilled professionals within BIM. This has been achieved by investigating the extent to which construction stakeholders in Ireland comprehend BIM and, examiningthe training …

Accelerating Bim Adoption In Ireland: A Ten-Year Review Of Cita Bim Gathering Proceedings, Alan Hore, Roger West, Barry Mcauley

Conference Papers

Digital construction interfaces have been studied extensively over the last few decades, with an ever-grow- ing catalogue of publications. The CitA BIM Gathering conferences have played a key role in bringing together the research and industry communities ina collaborative setting over the past decade in Ireland. In this paper the authors systematically review 10 years of papers published in the BIM Gathering pro- ceedings since the inaugural conference in 2013. A total of 175 papers involving over 200 authors have been reviewed and classified under the 2018 World Economic Forum (WEF) recommendations in respect to ac- celerating BIM adoption. The …

Industry Colloquium Report, Robert Moore

Reports

In the ever-evolving landscape of the construction industry, digital transformation has emerged as a pivotal force reshaping the way projects are conceived, executed, and delivered. This transformation, fuelled by cutting-edge technology and innovative practices, holds the promise of greater efficiency, sustainability, and collaboration within the construction sector.

This report offers a comprehensive summary of the Build Digital Project colloquium. It provides actionable insights and recommendations for clients, supply chain partners, and for prioritisation within the Build Digital Project pillars. As the industry partners seek to build a more efficient, sustainable, and collaborative construction sector, understanding and harnessing the invaluable insights …

Skills Matter – Up-Skilling Across Construction Stakeholders For Emerging Roles, Avril Behan, Paul Mccormack, Barry Mcauley

Conference Papers

The EU’s Climate Target Plan To 2030 (European Union 2020b) of achieving at least 55% reduction in Green House Gas emissions from 1990 levels, delivering towards a climate-neutral economy by 2050, requires systems-level change in the way we design, construct, and operate our built assets. Funding initiatives, such as co-ordinated by BUILD UP Skills, aim to deliver upskilling to the market but targets set by the European Skills Agenda may not be reached at current achievement levels. This paper presents the results of one completed and the progress of one ongoing Horizon 2020 funded project, BIMcert and ARISE, respectively. Learning …

The Current State Of Practice Of Building Information Modeling, Kevin P. Brooks

Masters Theses

Building Information Modeling (BIM) has become extremely prominent in the construction industry in the past twenty years. It serves as a digital repository that can, when used to its fullest potential, combine all aspects of designing, building, and managing a structure in one place, alongside all the data produced in those processes. The construction industry has to date struggled to increase productivity alongside similar fields, such as the manufacturing industry, though the construction industry generally has far more stakeholders on one project than the manufacturing industry. Further, building designs are becoming more complex while project schedules are becoming tighter. As …

Machine Learning-Based Seismic Damage Assessment Of Residential Buildings Considering Multiple Earthquake And Structure Uncertainties, Xinzhe Yuan, Liujun Li, Haibin Zhang, Yanping Zhu, Genda Chen, Cihan H. Dagli

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Wood-frame structures are used in almost 90% of residential buildings in the United States. It is thus imperative to rapidly and accurately assess the damage of wood-frame structures in the wake of an earthquake event. This study aims to develop a machine-learning-based seismic classifier for a portfolio of 6,113 wood-frame structures near the New Madrid Seismic Zone (NMSZ) in which synthesized ground motions are adopted to characterize potential earthquakes. This seismic classifier, based on a multilayer perceptron (MLP), is compared with existing fragility curves developed for the same wood-frame buildings near the NMSZ. This comparative study indicates that the MLP …

Development And Characterization Of Coal-Based Thermoplastic Composite Material For Sustainable Construction, Haibin Zhang, Wenyu Liao, Genda Chen, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The exploitation of coal and the disposal of waste plastic present significant environmental and economic challenges that require sustainable and profitable solutions. In response, we propose a renewable construction composite material of coal-based thermoplastic composite (CTC) that can be made from low-grade coal and plastic waste. We developed and tested the hot-press fabrication method for this CTC, using coal with a maximum particle size of 4.75 mm and recycled high-density polyethylene (HDPE). The effects of the coal fraction (50–80 wt.%) on compressive properties, thermal properties, microstructure, and ecological and economic efficiencies of the CTC were investigated. Test results revealed that …

A Spike-Shaped Anchorage For Steel Reinforced Polymer (Srp)-Strengthened Concrete Structures, Xingxing Zou, Keenan L. Mcburney, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel reinforced polymer (SRP) composite has recently emerged as an effective and economical solution for strengthening of reinforced concrete (RC) structures. Premature debonding failure of unanchored SRP at low load levels generally governs the performance of RC structures strengthened with externally bonded SRP. Therefore, a novel yet simple spike-shaped anchorage system was proposed in this study to prevent the debonding failure of SRP and to improve the interfacial shear capacity. Experimental investigation through single-lap shear tests of SRP-concrete joints showed that the anchorage system changed the failure mode from composite debonding to fiber rupture. In addition, the anchorage system substantially …

Xenabloom, Sophia Maglabe, Ryer Lauth, Elizabeth Shaw, Sheyna Rongong

Architectural Engineering

Proposal for an architectural and structural design of a shade structure at the Leaning Pine Arboretum, employing the Xenaform typology of Poly Shells, LLC.

Preliminary Bond Capacity Exploration Between Monolayer Graphene And Cementitious Composites, Yanping Zhu, Chuanrui Guo, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Aims to Explore Bond Capacity between Monolayer Graphene and Cementitious Composites for the First Time through a Pullout Test. the Low-Pressure Chemical Vapor Deposition Method Was Used to Synthesize Monolayer Graphene on the Copper Substrate to Be Embedded in the Mortar Made by the Briquette Mold. the Bond Capacity between Them Was Higher Than the Tensile Strength of the Copper Sheet with As-Grown Monolayer Graphene on the Surface Since All Specimens Failed in Fracture with Embedment Length of More Than 30 Mm. the Monolayer Graphene Enhanced the Copper Tensile Fracture Stress and Normalized Energy during the Test as …

Investigation Of Natural Pozzolans: Analyzing The Practicality Of Natural Pozzolans As A Partial Substitute For Cement In Grout Production, Jadyn I. Breien, Andrew J. Baro, Logan T. Marino

Architectural Engineering

This senior project aims to investigate whether natural pozzolans are more sustainable than fly ash and a sufficient substitute for cement in the production of grout. By following the intent of the ASTM (American Society of Testing and Materials) standards, a conclusion will be made to determine if natural pozzolans can contribute comparable strength in compression. The objective is to prove that natural pozzolans should be utilized in the production of grout rather than alternatives such as fly ash because it can provide similar strength while being more economical and more sustainable.

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Using Bim To Increase The Efficiency Of Energy-Driven Retrofitting Projects, Anne Grego, Shannon Chance, Barry Mcauley

Conference Papers

The building sector is responsible for nearly 40% of global energy consumption. Many existing buildings have poor thermal insulation and low energy performance, hindering sustainability goals. Energy-driven building retrofitting could address this issue and implementing Building Information Modelling (BIM) in retrofitting can reduce process time, costs, and waste associated with such undertakings. Yet, there is a lack of research and insufficient guidance for implementing BIM in energy-driven retrofitting. A BIM framework is presented to enhance decision-making processes during retrofitting. The aims of this study were to (1) identify BIM technologies and methodologies that could address existing barriers and improve efficiency …

3d Printing Of Earthen Materials: Toward The Carbon-Zero Construction, Shiva Bhusal

Civil Engineering ETDs

In recent years, digital manufacturing techniques in the architecture and construction industry have rapidly gained attention, especially with 3D printing, also called additive manufacturing. The use of cement has been common in modern construction and is now being explored for 3D printing. However, due to cement's contribution to approximately 7 percent of global carbon emissions and its high cost, research on sustainable and greener materials has gained attention. Previous studies on alternative construction have examined the mechanical and rheological properties of soil mixes, but not much attention has been given to printability evaluation, shrinkage, and cracking, which can affect the …

Song’S Site At Los Angeles Eco-Village Redevelopment, Kendall Gilbert, Marina Rios, Kristin Hernandez, Gianna Morelli

Honors Thesis

The Los Angeles Eco-Village (LAEV) is a co-op housing community, located in Koreatown, focused on building sustainable and economically cooperative living in an urban environment. The purpose of this project is to transform a property recently acquired by the LAEV, called Song’s, into a multipurpose community hub. The project design goals established with LAEV founder and community members, include cultivating new highly sustainable and resilient ideas on urban living and incorporating educational elements that inspire the community and visitors to live more sustainably. This project proposes three design elements to improve the community use of the newly acquired Song’s at …

Slo Botanical Garden Deck, Noah E. Demer

Architectural Engineering

This project consists of the design and construction of an outdoor-use deck. This deck is to be located in the NE corner of the Sage Meadow at the San Luis Obispo Botanical Garden at 3450 Dairy Creek Rd, San Luis Obispo, CA 93405. This deck’s intended use is as a gathering area for people to congregate. Originally, the ideal deck area was proposed as 700+ square feet, but with further site and project limitations the final design was ~480 square feet. This deck has not been constructed.

Design Of Wythe Connectors For Concentrated Out-Of-Plane Loading Of Insulated Walls, Ammar Al-Maabreh, Fray F. Pozo, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Partially composite concrete insulated wall panels must be designed to handle different types of loading, including out-of-plane concentrated loads. Currently, there is a lack of information that describes and helps engineers analyze the mechanics of axial load transfer for insulated wall panels for concentrated out-of-plane loads that may occur from lifting, handling, or floor/roof reactions. Such loading generates axial and shear forces in the wythe connectors, making it important to choose the type and quantity of connectors in the design process. This paper aims to develop a better understanding of out-of-plane point load mechanics on concrete sandwich wall panels. A …

Inter-Wythe Slip Design Criteria For Non-Composite Insulated Walls, Abdelrahman Awawdeh, Fray F. Pozo-Lora, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Non-composite insulated wall connector design is governed by ICC-ES AC320. This standard works entirely in the loading domain, asking the engineer to prevent connector failure due to tension and shear loading. In this paper, the authors discuss additional criteria related to thermal loading and out-of-plane wind loading that create displacement demand in the non-composite connectors. Loads suitable for such analyses are not well defined. Loads are assumed and demonstrated herein and shown to cause significant displacement demand on connectors. Limited non-composite wythe connector testing is available, and some results are presented here. A comparison indicates that outright failure of non-composite …

How Can Visual Programing Be Used To Aid The Development Of A Structural Scheme Design Process Utilising Geometric Data Within An Architectural Revit Model?, Ed Carthy, Kieran Lakhera O'Shea

Reports

The early-stage structural scheme design of a building is a complex task requiring the collection of multiple information categories such as geometry, loading and materials. The collection and review of this information is traditionally conducted in a 2D environment. This is inefficient, time-consuming, and tedious. This paper provides a review of how structural engineers’ understanding and implementation of BIM has evolved significantly in recent years, validated by extant literature in areas such as BIM automation, visual programming, and structural optimisation in the structural engineering sector. Structural engineers are growing more aware that BIM provides a vast repository of data to …

Thermal Efficacy Of Green Walls In Building Structures In The Northeast United States, Nathaniel Wright

Student Showcase

Climate change is one of the most threatening issues that humankind faces in the 21st century and there is indisputable evidence that our planet is experiencing global temperature rise, shrinking of ice sheets and sea level rise, warming oceans, and extreme weather events at an alarming rate. Urbanization drives these changes and creates the Urban Heat Island (UHI) effect. One method to mitigate this issue is urban greening, specifically the construction of green walls which take advantage of unused vertical exteriors of buildings. Despite existing literature on green walls especially in Europe and Asia, green walls must be researched more …

Reduction Of Embodied Carbon In Buildings Through Use Of Low Carbon Strategies And Standardization And Enforcement Of Life Cycle Assessment, Bhargavi Sai Sudhakar

Master's Projects and Capstones

The building and construction industry is energy intensive and as of 2021, this industry is responsible for 37% of the total global greenhouse gas emissions. In previous studies of conventional buildings, the operational energy of a building contributed to 80% and the embodied energy contributed to 20% of the total life cycle energy. With increase in policies and standards that focus on reducing the operational energy, low energy and certified green buildings have emerged where the operational energy has considerably reduced. The relative and absolute share of embodied energy in these energy efficient buildings have increased due to excessive use …

Energy Efficiency Retrofit And Decarbonization Of Old And Historic Buildings In California, Daria Nikolaeva

Master's Projects and Capstones

Buildings are responsible for almost 40% of total global greenhouse gas emissions and the retrofitting of existing buildings is an essential part of solving the problem. About 75% of buildings in Californian were constructed before the first energy-efficiency building code was adopted in 1978. Old buildings are inefficient, responsible for large carbon footprints and must be retrofitted to stay on track with the state's climate targets. However, current policies do not require substantial changes and tend to favor historic preservation over energy efficiency, missing improvement opportunities. Recognizing the significance of carbon intensity, the 2019 California Energy Efficiency Action Plan shifted …