Biomedical Engineering and Bioengineering Commons^™

Morphology Of The Acromion And Scapular Spine With Special Interest In The Strength & Failure Prediction After Reverse Total Shoulder Replacement, Andrei M. Matusa, Cole Fleet, George S. Athwal, James A. Johnson

Undergraduate Student Research Internships Conference

Scapular spine fractures following a reverse arthroplasty are a significant clinical concern. This ongoing study looks at the morphology of the acromion and scapular spine with an interest in the strength and failure prediction of the bone. Digital 3D models of the scapular spine were created from cadaver CTs, then bone density and distribution data was obtained. It was found that the cortical bone was most dense just medial of the lateral angle. The cross-sectional area here was also the largest and decreased medially. This has important implications for implant fixation hardware as cortical bone --compared to cancellous bone-- is …

Tca Fabrication Devices, Brendan R. Difabio

Undergraduate Student Research Internships Conference

Twisted coil actuators are a recent technology that has different properties from popular actuators used today. Being so new, there is still much to learn about these actuators. This project aims to create devices that can be used to make the fabrication process simple and repeatable.

Producing And Measuring Oscillatory Shear In A Novel Microfluidic Chip, Sanaz Lordfard, Daniel Lorusso, Tamie L. Poepping, Hristo N Nikolov, Kayla Soon, Stephen Sims, Jeffrey Dixon, David Holdsworth

Undergraduate Student Research Internships Conference

Purpose: To demonstrate the effectiveness of a novel microfluidic device mimicking oscillatory blood flow, allowing cell biologists to examine how endothelial cells respond to a range of oscillatory shear stress levels.

Methods: The microfluidic chip consists of a circular-shaped reservoir, leading to a rectangular channel that is examined under a microscope. The plunger is connected to a speaker system and oscilloscope, allowing the plunger to apply a range of frequencies (5-60Hz) and voltages (5-10 V, leading to a variety in oscillation amplitudes) to the reservoir region. 1.1 um fluorescent particles diluted in distilled water were used for tracking. Processing was …

Intracardiac Ultrasound Guided Systems For Transcatheter Cardiac Interventions, Hareem Nisar

Electronic Thesis and Dissertation Repository

Transcatheter cardiac interventions are characterized by their percutaneous nature, increased patient safety, and low hospitalization times. Transcatheter procedures involve two major stages: navigation towards the target site and the positioning of tools to deliver the therapy, during which the interventionalists face the challenge of visualizing the anatomy and the relative position of the tools such as a guidewire. Fluoroscopic and transesophageal ultrasound (TEE) imaging are the most used techniques in cardiac procedures; however, they possess the disadvantage of radiation exposure and suboptimal imaging. This work explores the potential of intracardiac ultrasound (ICE) within an image guidance system (IGS) to facilitate …

A Two-Layer Continuous-Capillary Oxygen Transport Model: Development And Application To Blood Flow Regulation In Resting Skeletal Muscle., Keith C. Afas

Electronic Thesis and Dissertation Repository

In skeletal muscle (SM), the microcirculation distributes blood flow to capillary networks to meet local oxygen (O₂) demand. Experiments using intra-vital video microscopy (IVVM) have quantified blood flow and O₂ supply in capillary networks, and using an O₂ exchange chamber have measured local changes in blood flow believed due to O₂-dependent regulation. However, IVVM is unable to simultaneously measure capillary O₂ supply and SM O₂ content, implying the need for theoretical models to understand how flow regulation and SM oxygenation interact. In this thesis, a novel blood-tissue O₂ transport model using …

Motion And Crosslinked Polyethylene Wear In Reverse Total Shoulder Arthroplasty, Christopher Millward

Electronic Thesis and Dissertation Repository

The reverse total shoulder arthroplasty (RTSA) has quickly grown to become the most commonly used shoulder arthroplasty design; however, reports have shown evidence of RTSA failures related to polyethylene wear and damage. Therefore, the present work investigated the wear of crosslinked polyethylene (XLPE) in environments similar to that of an in vivo RTSA. Additionally, a computational model was developed based on a previous study of the shoulder motions obtained from a selection of typical patients with RTSA. This model quantified the amount of glenohumeral motion that an RTSA may be subjected to in vivo and provided an approximate value for …

Large-Scale Analysis And Automated Detection Of Trunnion Corrosion On Hip Arthroplasty Devices, Anastasia M. Codirenzi

Electronic Thesis and Dissertation Repository

Corrosion at the modular head-neck taper interface of total and hemiarthroplasty hip implants (trunnionosis) is a cause of implant failure and thus a clinical concern. Patient and device factors contributing to the occurrence of trunnionosis have been investigated in prior implant retrieval studies. The Goldberg corrosion scoring method is considered the gold standard for observing trunnionosis, but it is labour-intensive. As a result, previous studies have generally looked at under 250 implants for analysis. The purpose of this thesis was to do a large-scale analysis of trunnionosis and explore its relationship to device and patient factors and compare to previously …

Biomechanical Investigation Of Complete And Partial Medial Collateral Ligament Injuries, Callahan Doughty

Electronic Thesis and Dissertation Repository

The medial collateral ligament (MCL) is composed of two major components: the deep MCL (dMCL) and superficial MCL (sMCL). Recent indications have raised questions as to the validity of previous descriptions of the MCL’s role in knee stability. Despite the relative likelihood of partial injuries to the sMCL, as opposed to complete tears, the impact of these injuries remains largely misunderstood. This thesis set out to (1) interpret the roles of the sMCL and dMCL; and (2) investigate the effect of partial sMCL injuries on knee stability.

A joint motion simulator was used to determine the role of the dMCL …

Development Of Brain-Derived Bioscaffolds For Neural Progenitor Cell Culture And Delivery, Julia Terek

Electronic Thesis and Dissertation Repository

The use of brain extracellular matrix (ECM) as a biomaterial has the potential to promote neural tissue regeneration by providing cell-instructive cues that direct survival, proliferation, and differentiation. This study developed a novel detergent-free decellularization protocol that effectively reduced cellular content while preserving key ECM components in porcine and rat brains. The resulting decellularized brain tissue (DBT) was incorporated into microcarriers to assess its effects on the growth, phenotype and neurotrophic factor gene expression of rat brain-derived progenitor cells cultured within spinner flask bioreactors, using purified collagen microcarriers as a control. Both types of microcarriers supported cell expansion and survival, …

Early Biological Response Of Articular Cartilage To Hemiarthroplasty Wear, Debora Rossetti

Electronic Thesis and Dissertation Repository

Hemiarthroplasties typically result in accelerated wear of the preserved side of the joint, resulting in suboptimal clinical outcomes and limited longevity. This in vitro study investigated the effects of hemiarthroplasty implant curvature on the early biological response of articular cartilage measured by proteoglycan release, histology, and surface morphology. Cartilage from boar radiocarpal joints were worn by metal pins of varying radii of curvature (RoC) using a pin-on-plate wear simulator. Histology and proteoglycan assays showed no significant differences between RoC treatment groups, and proteoglycan assays showed increased proteoglycan release 72 hours after wear testing in worn cartilage specimens compared to control …

The Application Of Digital Volume Correlation Bone Strain Measurements In The Osteoarthritic Glenohumeral Joint, Jakub R. Targosinski

Electronic Thesis and Dissertation Repository

This thesis investigates the accuracy and precision of digital volume correlation measurements derived from micro-computed tomography imagery of interfaces in the upper extremity of clinical relevance, namely, the implant-cement-bone interface of glenoid implants used in total shoulder arthroplasties and the implant-bone interface of shoulder hemiarthroplasties. The works within derive relationships between measurement accuracy and precision and parameters of practical interest such as image quality and measurement spatial resolution. It also analyzes the effects of micro-computed tomography image artifact-inducing materials on the accuracy and precision of digital volume correlation-based measurements and the spatial relationship between distance between the artifacting material and …

A Novel Ultrasound Elastography Technique For Evaluating Tumor Response To Neoadjuvant Chemotherapy In Patients With Locally Advanced Breast Cancer, Niusha Kheirkhah

Electronic Thesis and Dissertation Repository

Breast cancer is the second most diagnosed cancer in women, estimated to affect 1 in 8 women during their lifetime. About 10% to 20% of new breast cancer cases are diagnosed with locally advanced breast cancer (LABC). LABC tumors are usually larger than 5 cm and/or attached to the skin or chest wall. It has been reported that when such cases are treated with surgery alone, metastasis and mortality rates are high, especially where skin involvement or attachment to the chest wall is extensive. As such, efficient treatment for this kind of breast cancer includes neoadjuvant chemotherapy (NAC) to shrink …

The Effects Of A Porous Internal Lattice Design On The Articular Contact Mechanics Of Radial Head Hemiarthroplasty Implants, Jessica Benitah

Electronic Thesis and Dissertation Repository

Hemiarthroplasty, where one side of a joint is replaced, is a minimally invasive procedure. It allows for the preservation of native tissue, though a significant ramification is accelerated cartilage wear when articulating with high stiffness materials that do not mimic the mechanical stiffness of the native tissue. An implant that employs a lattice design can significantly lower the stiffness of a solid structure whilst maintaining strength. This study was conducted to investigate the effect of implementing a porous internal lattice structure with a thin outer shell on the articular contact mechanics, using a radial head hemiarthroplasty. It was hypothesized that …

The Bio-Mechanical Development And Kinematic Evaluation Of Zone I And Zone Ii Injuries And Their Corresponding Surgical Repair Techniques Using An In-Vitro Active Finger Motion Simulator: A Cadaveric Study, Mohammad Haddara

Electronic Thesis and Dissertation Repository

Research development involving large scale joint mechanics and biomechanical adaptations is growing. However, interest in smaller scale joints, such as the fingers, is limited. Thus, the present work describes the enhancement and clinical application of a previously designed in-vitro active finger motion simulator in measuring and assessing intrinsic joint kinematics and tissue biomechanics including load transfer and strains induced tissues within the finger. Accuracy of electromagnetic tracking (EM) systems were evaluated compared to the standard optical tracking systems and used to develop motion derived finger joint coordinate systems. Moreover, minute strain gauges were utilized to measure strains induced by the …

Sol-Gel Derived Bioceramic Poly(Diethyl Fumarate – Co – Triethoxyvinylsilane) Composite, Aref Sleiman

Electronic Thesis and Dissertation Repository

Synthetic bone graft materials have become an increasingly popular choice for bone augmentation. Ceramic-based and polymer-based bone graft materials constitute the two main classes of synthetic bone graft materials. This study investigated the synthesis of novel bioactive composites for their potential use as bone graft biomaterials. Poly(diethyl fumarate-co-triethoxyvinylsilane)/bioceramic class II organic/inorganic hybrid biomaterials were synthesized via a sol gel process. These biomaterials were then reacted with an ammonium phosphate solution to prepare their respective composites. For the first time, we successfully synthesized sol-gel derived bioceramic poly(diethyl fumarate-co-triethoxyvinylsilane) composites. In vitro bioactivity evaluation of poly(diethyl fumarate-co-triethoxyvinylsilane)/bioceramic composites in simulated body fluid …

Cost-Effective Non-Destructive Testing Of Biomedical Components Fabricated Using Additive Manufacturing, Santiago Fabian Cobos

Electronic Thesis and Dissertation Repository

Biocompatible titanium-alloys can be used to fabricate patient-specific medical components using additive manufacturing (AM). These novel components have the potential to improve clinical outcomes in various medical scenarios. However, AM introduces stability and repeatability concerns, which are potential roadblocks for its widespread use in the medical sector. Micro-CT imaging for non-destructive testing (NDT) is an effective solution for post-manufacturing quality control of these components. Unfortunately, current micro-CT NDT scanners require expensive infrastructure and hardware, which translates into prohibitively expensive routine NDT. Furthermore, the limited dynamic-range of these scanners can cause severe image artifacts that may compromise the diagnostic value of …

The Role Of Transient Vibration Of The Skull On Concussion, Rodrigo Dalvit Carvalho Da Silva

Electronic Thesis and Dissertation Repository

Concussion is a traumatic brain injury usually caused by a direct or indirect blow to the head that affects brain function. The maximum mechanical impedance of the brain tissue occurs at 450±50 Hz and may be affected by the skull resonant frequencies. After an impact to the head, vibration resonance of the skull damages the underlying cortex. The skull deforms and vibrates, like a bell for 3 to 5 milliseconds, bruising the cortex. Furthermore, the deceleration forces the frontal and temporal cortex against the skull, eliminating a layer of cerebrospinal fluid. When the skull vibrates, the force spreads directly to …

Contact‐Free Remote Manipulation Of Hydrogel Properties Using Light‐Triggerable Nanoparticles: A Materials Science Perspective For Biomedical Applications, Cho-E Choi, Aishik Chakraborty, Ali Coyle, Yasmeen Shamiya, Arghya Paul

Chemical and Biochemical Engineering Publications

Considerable progress has been made in synthesizing “intelligent”, biodegradable hydrogels that undergo rapid changes in physicochemical properties once exposed to external stimuli. These advantageous properties of stimulus-triggered materials make them highly appealing to diverse biomedical applications. Of late, research on the incorporation of light-triggered nanoparticles (NPs) into polymeric hydrogel networks has gained momentum due to their ability to remotely tune hydrogel properties using facile, contact-free approaches, such as adjustment of wavelength and intensity of light source. These multi-functional NPs, in combination with tissue-mimicking hydrogels, are increasingly being used for on-demand drug release, preparing diagnostic kits, and fabricating smart scaffolds. Here, …

Leveraging The Advancements In Functional Biomaterials And Scaffold Fabrication Technologies For Chronic Wound Healing Applications, Alap A. Zahid, Aishik Chakraborty, Yasmeen Shamiya, Shruthi Polla Ravi, Arghya Paul

Chemical and Biochemical Engineering Publications

Exploring new avenues for clinical management of chronic wounds holds the key to eliminating socioeconomic burdens and health-related concerns associated with this silent killer. Engineered biomaterials offer great promise for repair and regeneration of chronic wounds because of their ability to deliver therapeutics, protect the wound environment, and support the skin matrices to facilitate tissue growth. This mini review presents recent advances in biomaterial functionalities for enhancing wound healing and demonstrates a move from sub-optimal methods to multi-functionalized treatment approaches. In this context, we discuss the recently reported biomaterial characteristics such as bioadhesiveness, antimicrobial properties, proangiogenic attributes, and anti-inflammatory properties …

Towards Fluoro-Free Interventions: Using Radial Intracardiac Ultrasound For Vascular Navigation, Hareem Nisar, Leah Groves, Leandro Cardarelli-Leite, Terry M Peters, Elvis C.S. Chen

Robarts Imaging Publications

Transcatheter cardio-vascular interventions have the advantage of patient safety,reduced surgery time, and minimal trauma to the patient's body. Transcathetherinterventions, which are performed percutaneously, suffer from the lack of direct line-of-sight with the surgical tools and the patient anatomy. Therefore, such interventionalprocedures rely heavily on image guidance for navigating towards and deliveringtherapy at the target site. Vascular navigation via the inferior vena cava (IVC), from thegroin to the heart, is an imperative part of most transcatheter cardiovascularinterventions such as valve repair surgeries and ablation therapy. Traditionally, the IVCis navigated using fluoroscopic techniques such as angiography or CT venography.These X-ray based techniques …

Biomechanical Analysis Of Ligament Modelling Techniques And Femoral Component Malrotation Following Tka, Liam A. Montgomery

Electronic Thesis and Dissertation Repository

Previous studies have demonstrated that satisfaction and revision rates following total knee arthroplasty (TKA) are lower than those of comparable surgeries such as total hip replacements. A leading cause for these revisions is joint instability which may be due to improper ligament balancing or poorly aligned surgical implants. One of the methods used to investigate biomechanical forces and kinematics is computational modelling of the post-operative TKA knee.

A unique knee model was used to investigate the biomechanical and kinematic effects of ligament model complexity, as well as the effects of simulating ligament wrapping versus ignoring ligament wrapping. We then used …

Seizure Detection Using Deep Learning, Information Theoretic Measures And Factor Graphs, Bahareh Salafian

Electronic Thesis and Dissertation Repository

Epilepsy is a common neurological disorder that disrupts normal electrical activity in the brain causing severe impact on patients’ daily lives. Accurate seizure detection based on long-term time-series electroencephalogram (EEG) signals has gained vital importance for epileptic seizure diagnosis. However, visual analysis of these recordings is a time-consuming task for neurologists. Therefore, the purpose of this thesis is to propose an automatic hybrid model-based /data-driven algorithm that exploits inter-channel and temporal correlations. Hence, we use mutual information (MI) estimator to compute correlation between EEG channels as spatial features and employ a carefully designed 1D convolutional neural network (CNN) to extract …

The Use Of Ct To Assess Shoulder Kinematics And Measure Glenohumeral Arthrokinematics, Baraa Daher

Electronic Thesis and Dissertation Repository

Recently, studies have started employing dynamic four-dimensional computed tomography (4DCT) imaging as a biomechanical assessment tool. These studies would benefit from the valuable work that has been done in the past using three-dimensional computed tomography (3DCT). Thus, a structured review was conducted to examine the extent and range of methods employing CT imaging to measure shoulder kinematics. The findings of the review were utilized to conduct a study that employed 4DCT imaging to measure glenohumeral joint congruency and arthrokinematics during internal rotation to the back in a population of healthy individuals. The results of this work show the importance of …

Investigation Of Human Adipose-Derived Stem-Cell Behavior Using A Cell-Instructive Polydopamine-Coated Gelatin-Alginate Hydrogel., Settimio Pacelli, Aparna R Chakravarti, Saman Modaresi, Siddharth Subham, Kyley Burkey, Cecilia Kurlbaum, Madeline Fang, Christopher A Neal, Adam J Mellott, Aishik Chakraborty, Arghya Paul

Chemical and Biochemical Engineering Publications

Hydrogels can be fabricated and designed to exert direct control over stem cells' adhesion and differentiation. In this study, we have investigated the use of polydopamine (pDA)-treatment as a binding platform for bioactive compounds to create a versatile gelatin-alginate (Gel-Alg) hydrogel for tissue engineering applications. Precisely, pDA was used to modify the surface properties of the hydrogel and better control the adhesion and osteogenic differentiation of human adipose-derived stem cells (hASCs). pDA enabled the adsorption of different types of bioactive molecules, including a model osteoinductive drug (dexamethasone) as well as a model pro-angiogenic peptide (QK). The pDA treatment efficiently retained …

Organic-Inorganic Hybrid Biomaterials For Bone Tissue Engineering And Drug Delivery, Neda Aslankoohi

Electronic Thesis and Dissertation Repository

Bone biomaterials prepared from a combination of biodegradable polymers and bioactive glasses offer several advantages, including favorable cell interactions, selective gene expression, and delivery of biomolecules. Furthermore, the interaction of the organic and inorganic phases at the molecular level results in a single-phase hybrid material possessing synergistic properties.

This research aimed to design bone biomaterials from α-amino acid-based poly(ester amide) (PEA) and tertiary bioactive glasses using a sol-gel process. Since incorporating calcium into the bioactive glass network is challenging at sol-gel reaction temperatures, calcium ethoxide and calcium chloride were studied as precursors, and the optimum reaction conditions were identified. Mesoporous …

Characterization Of Tissue-Specific Matrix-Derived Bioscaffolds For Nucleus Pulposus Cell Culture, Marco A. Herrera Quijano

Electronic Thesis and Dissertation Repository

Bioscaffolds derived from the extracellular matrix (ECM) have shown the capacity to promote regeneration by providing tissue-specific biological instructive cues that can enhance cell survival and direct lineage-specific differentiation. This study focused on the development and characterization of two-dimensional (2-D) and three-dimensional (3-D) cell culture platforms incorporating decellularized nucleus pulposus (DNP). First, a novel detergent-free protocol was developed for decellularizing bovine NP tissues that was effective at removing cellular content while preserving key ECM constituents including collagens and glycosaminoglycans. Culture studies showed that 2-D coatings derived from the DNP could support cell attachment but did not maintain or rescue the …

Mixed-Reality Visualization Environments To Facilitate Ultrasound-Guided Vascular Access, Leah Groves

Electronic Thesis and Dissertation Repository

Ultrasound-guided needle insertions at the site of the internal jugular vein (IJV) are routinely performed to access the central venous system. Ultrasound-guided insertions maintain high rates of carotid artery puncture, as clinicians rely on 2D information to perform a 3D procedure. The limitations of 2D ultrasound-guidance motivated the research question: “Do 3D ultrasound-based environments improve IJV needle insertion accuracy”. We addressed this by developing advanced surgical navigation systems based on tracked surgical tools and ultrasound with various visualizations. The point-to-line ultrasound calibration enables the use of tracked ultrasound. We automated the fiducial localization required for this calibration method such that …

4dct Analysis Of In-Vivo Carpal Kinematics During Fem, Manisha R. Mistry

Electronic Thesis and Dissertation Repository

A consensus, detailed understanding of carpal kinematics remains elusive. 4-dimensional CT (4DCT) is a validated modality capable of accurately studying in-vivokinematic motion. The objective of this work is to quantify normal, in-vivo kinematic motion of the carpus through a flexion-extension arc of motion using 4DCT. Ten healthy, un-injured volunteers underwent a 4DCT scanning protocol through a complete arc of flexion-extension motion. Kinematic changes in motion were quantified using helical axis motion data for each carpal bone. Helical axes were compared between bones and statistical analysis performed using repeated-measures ANOVA to identify difference in kinematic motion between bones (p<0.05). The carpus can be divided into four main kinematic blocks: the distal carpal block, the proximal carpal block and individual scaphoid and trapezial blocks. This work supports an additional segmentation of the trapezium from the distal carpal row, which suggests some modulation between the scaphoid and distal carpal row.

Development Of A Low-Cost Algometer, Thomas D. Naish, Ana Luisa Trejos, Dave M. Walton

Undergraduate Student Research Internships Conference

Many people suffer from chronic pain, the reasons for which are not always well understood. Algometers are instruments that can help clinicians understand the nature of pain by determining the force at which pain becomes noticeable or unbearable. Algometers can also be used to determine the effects that external influences can have on pain tolerance in healthy people.

The goal of this project was to develop an algometer that can measure the normal range of pain thresholds and tolerances of most patients, which ranges up to 35 lbs. Also, the result needed to be accurate to about 1% and made …

Digital Navigation For Shoulder Arthroplasty, Jeremy Silver-Mahr

Undergraduate Student Research Internships Conference

No abstract provided.