Open Access. Powered by Scholars. Published by Universities.®

Automotive Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 6 of 6

Full-Text Articles in Automotive Engineering

Investigation Of Low Reynolds Number Flow And Heat Transfer Of Louvered Surfaces, Pradeep R. Shinde Nov 2016

Investigation Of Low Reynolds Number Flow And Heat Transfer Of Louvered Surfaces, Pradeep R. Shinde

FIU Electronic Theses and Dissertations

This study focuses on the investigation of flow behavior at low Reynolds numbers by the experimental and numerical performance testing of micro-channel heat exchangers. An experimental study of the heat transfers and pressure drop of compact heat exchangers with louvered fins and flat tubes was conducted within a low air-side Reynolds number range of 20 < ReLp < 225. Using an existing low-speed wind tunnel, 26 sample heat exchangers of corrugated louver fin type, were tested. New correlations for Colburn j and Fanning friction f factor have been developed in terms of non-dimensional parameters. Within the investigated parameter ranges, it seems that both the j and f factors are better represented by two correlations in two flow regimes (one for ReLp = 20 – 80 and one for ReLp = 80 – 200) than a single regime correlation in the power-law format. The results support the conclusion that airflow and heat transfer at very low Reynolds numbers behaves differently from that at higher Reynolds numbers ...


Design Of Real-Time Combustion Feedback System And Experimental Study Of An Rcci Engine For Control, Jayant Kumar Arora Jan 2016

Design Of Real-Time Combustion Feedback System And Experimental Study Of An Rcci Engine For Control, Jayant Kumar Arora

Dissertations, Master's Theses and Master's Reports

Premixed compression ignition (PCI) technologies offer high efficiency and low emissions but are usually confined by limited operation range as well as high pressure rise and heat release rate. In this work, a more recently developed PCI mode is explored where in-cylinder blending of two fuels with different auto-ignition characteristics (diesel and gasoline) is utilized to create reactivity stratification such that heat release rate and combustion timing can be controlled. This mode has been defined as Reactivity Controlled Compression Ignition (RCCI).

As part of this thesis, the main aim is to study various parameters that can be used to control ...


Automated X-Ray Quality Control Of Catalytic Converters, N. Shashishekhar, Veselitza Jan 2016

Automated X-Ray Quality Control Of Catalytic Converters, N. Shashishekhar, Veselitza

Review of Progress in Quantitative Nondestructive Evaluation

Catalytic converters are devices attached to the exhaust system of automobile or other engines to eliminate or substantially reduce polluting emissions. They consist of coated substrates enclosed in a stainless steel housing. The substrate is typically made of ceramic honeycombs; however stainless steel foil honeycombs are also used. The coating is usually a slurry of alumina, silica, rare earth oxides and platinum group metals. The slurry also known as the wash coat is applied to the substrate in two doses, one on each end of the substrate; in some cases multiple layers of coating are applied. X-ray imaging is used ...


An Experimental Investigation Of The Effect Of Temperature And Space Velocity On The Performance Of A Cu-Zeolite Flow-Through Scr And A Scr Catalyst On A Dpf With And Without Pm Loading, Vaibhav Kadam Jan 2016

An Experimental Investigation Of The Effect Of Temperature And Space Velocity On The Performance Of A Cu-Zeolite Flow-Through Scr And A Scr Catalyst On A Dpf With And Without Pm Loading, Vaibhav Kadam

Dissertations, Master's Theses and Master's Reports

Abstract The heavy-duty diesel (HDD) engines use the diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and urea injection based selective catalytic reduction (SCR) systems in sequential combination, to meet the US EPA 2010 PM and NOₓ emission standards. The SCR along with a NH₃ slip control catalyst (AMOX) offer NOₓ reduction >90 % with NH₃ slipHowever, there is a strong desire to further improve the NOₓ reduction performance of such systems, to meet the California Optional Low NOₓ Standard implemented since 2015. Integrating SCR functionality into a diesel particulate filter (DPF), by coating the SCR catalyst on the DPF, offers ...


Competition Vehicle Based Intake Manifold Design, Joshua N. Matiash Jan 2016

Competition Vehicle Based Intake Manifold Design, Joshua N. Matiash

Dissertations, Master's Theses and Master's Reports

A competitive vehicle in Formula SAE needs to be easy for unskilled drivers to extract the maximum performance from. This requires a predictable and manageable torque curve. This report details the development of an intake manifold for a Formula SAE car from a vehicle-based approach to produce this manageable and predictable torque. The current vehicle was instrumented and driven on a representative track to determine the usage of available torque. Based on these findings an ideal torque curve was chosen that favored increased torque at upper engine speed ranges and decreased torque at lower engine speed ranges. A 1-D engine ...


Experimental Study, Modelling And Controller Design For An Rcci Engine, Naga Nithin Teja Kondipati Jan 2016

Experimental Study, Modelling And Controller Design For An Rcci Engine, Naga Nithin Teja Kondipati

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) has got widespread attention over the past two decades in the field of Automotive Research and Development due to it’s potential for achieving higher efficiencies with near-zero engine out NOx and soot emissions. Among all the LTC strategies Reactivity controlled compression ignition (RCCI) has shown the most promising results due to it’s precise control over combustion phasing and heat release rate. However, RCCI being a dual-fuel stratified combustion, precise control over the injection timing of direct injected fuel and in-cylinder fuel reactivity of the mixture needs to be controlled effectively in order to achieve ...