Automotive Engineering Commons^™

Limited Assessment Of A Selected Particulate Matter Sensor Technology In Emission Measurement Applications On Diesel Vehicles, Svetlana Korotkova Espinosa

Dissertations and Theses @ UNI

The study assessed the ability of a novel particle sensor to provide adequate evaluation of real-time emissions from modem diesel engines and estimate the effectiveness of emission control devices. Emission data were obtained from vehicles in real-world field conditions under various test cycles. The datasets were used to determine whether there is an association between particulate matter (PM) measurements produced by particle sensor and the PM measurements from reference instrument. Exploratory analysis was combined with statistical techniques to investigate suitability of particle sensor to adequately measure PM mass concentrations in exhaust gases of modem diesel vehicles. Results of the study …

Development Of A Modular Dual Engine Hybrid Electric Vehicle Simulation Model, Kenan Baltaci

Dissertations and Theses @ UNI

Depleting resources of fossil fuel, climate change impacts, high oil prices, and strict emission requirements are leading to the research on efficient, environmentally friendly, and lowered fossil fuel dependent solutions in the transportation field. While a number of studies used computer modeling and simulation tools to investigate hybrid electric vehicles (HEVs), very few attempted to model and simulate a dual-engine hybrid vehicle. Designing a vehicle engine to meet energy needs in the fully loaded condition is not an optimal solution for manufacturers and customers. The larger the engine, the higher the manufacturing costs for companies, and higher fuel consumption for …

Inventory Simulation And Optimization Using System Dynamics, Structural Modeling Equations And Genetic Algorithms In The Drivetrain Division Of An Automotive Manufacturer, Marco Sisfontes-Monge

Dissertations and Theses @ UNI

Strategic planning and control are among the most critical activities that modern enterprises require to succeed in the global economy. This research is an original study that investigated the combination of tools and methodologies in order to apply them to a midwestern tractor manufacturer. The current study identified the constraints applicable to a polishing line in the Drivetrain Division of a major tractor manufacturer interested in exploring alternative techniques to improve its worldwide manufacturing operations.

The specific questions that this project tried to respond are stated as follows:

1. What were the most important variables that affected inventory levels of an …

Building A Comprehensive Energy Model For Off-Highway Vehicles With Emphasis On Vehicle Thermal Control Systems, Ayhan Zora

Dissertations and Theses @ UNI

Utilizing machine and thermal system simulations (vehicle energy models) can be very helpful for vehicle manufacturing companies to develop a machine with acceptable component temperatures, less heat loads to the vehicle cooling systems, and reduced emissions that will also reduce overall product development cycle.

Energy models of vehicles were developed mostly in the automotive industry, and most of these studies were based on partial energy models.

The aim of this research study was to create a comprehensive energy model for agricultural machinery, which will be a basis for future work on similar products. A tractor model from a Midwest off-road …

Oil Consumption Measurements Of A Production Engine Using The Sulfur-Trace Method, Verlyn Royal Benson

Dissertations and Theses @ UNI

Controlling the oil consumption of diesel engines is important for customer satisfaction. Existing oil consumption measurement methods are adequate; however, improved methods offer the possibility of faster and more comprehensive results. The sulfur-trace method is an example.

Major objectives of this investigation were to adopt a sulfur-trace analyzer for oil consumption measurements, to improve the oil consumption measurement process, and to demonstrate application of the sulfur-trace instrument to individual cylinder sampling. To achieve these objectives, four research questions were applied:

1. What procedures and attention to detail are required?
2. How can results be reported to maximize data interpretation?
3. How do the …

Investigation Of The Relationship Between Fuel Injection Nozzle Roto Flow And Hydra Flow And The Engine Torque Of A Diesel Engine, Guang Jin

Dissertations and Theses @ UNI

The purpose of this study was to investigate the possibility of reducing diesel engine torque variation by optimizing fuel injection nozzle tip configuration. In order to reduce engine torque variation, test runs were conducted to determine whether fuel injection nozzles affected diesel engine torque. There was a further effort to determine whether a correlation existed between the fuel injection nozzle roto flow and hydra flow, and the engine torque at specified engine speeds.

Engines installed in cotton pickers and tractors were used for this study. Engines, five from the cotton picker and five from the tractor group were chosen randomly …

An Analysis Of The Importance Of Selected Applied Physics Concepts As Prerequisites To Training In Automotive Technology, Patrick Michael Mccleskey

Dissertations and Theses @ UNI

The purpose of this study has been to develop information that may be useful in the preparation of curriculums and materials dedicated to the remediation of applied physics knowledge and skill deficits demonstrated by entering automotive technology students. The problem was to identify and rank-order the importance of applied physics concepts within the mechanical, fluidal, electrical/electronic, thermal, and chemical domains that are foundational to training in automotive technology.

A questionnaire containing 77 concept statements with a corresponding graphic rating scale was administered via mailed correspondence to all 196 of California's full-time community college automotive instructors. Of these, 130 (66.33%) were …

The System Design And Evaluation Of A Microprocessor Controlled Dispenser Using A Radar Ground-Speed Sensor, Yu-Charn Chen

Dissertations and Theses @ UNI

This experimental research focused on the design of a new approach to control seed dispensers and to analyze the performance characteristics of a Doppler radar ground speed sensor for a microprocessor control dispenser. The research focused on comparing the effectiveness of using a radar unit with a fifth-wheel encoder for measuring ground speed when both were connected to a microprocessor controlled seed dispenser.

The system designed for this study consisted of hardware and a computer program in 6502 assembly language. The hardware for this study consisted of a monitor device, microprocessor control unit, stepper motor, fifth-wheel encoder, Doppler radar and …