Automotive Engineering Commons^™

Framing Automation Trust: How Initial Information About Automated Driving Systems Influences Swift Trust In Automation And Trust Repair For Human Automation Collaboration, Scott Anthony Mishler

Psychology Theses & Dissertations

The study examines how trust in automation is influenced by initial framing of information before interaction and how later active calibration methods can further influence trust repair or dampening after an automation error in a three-experiment study. As more human drivers begin to use automated driving systems (ADSs) for the first time, their initial understanding of the system can influence their trust leading to a miscalibration of trust. Prior studies have investigated how trust develops through interactions with an automated system, but few have looked at integrating swift trust and framing to calibrate trust before interaction and investigate further active …

Attention And Task Engagement During Automated Driving, James Richard Unverricht

Psychology Theses & Dissertations

Many young drivers suffer fatal crashes each year in the United States at a rate approximately three times greater than more experienced drivers. Automated driving systems may serve to mitigate young drivers high crash rates but remain underexplored in research. This dissertation project examined the effects of levels of automation and interestingness of auditory clips on latent hazard anticipation in young drivers during simulated driving. Participants drove a vehicle at varying levels of vehicle automation (SAE Level 0, 2, or 3) in simulated scenarios, each containing a latent hazard event during which a boring, neutral, or interesting auditory clip was …

Move: Mobile Observers Variants And Extensions, Ryan Florin

Computer Science Theses & Dissertations

Traffic state estimation is a fundamental task of Intelligent Transportation Systems. Recent advances in sensor technology and emerging computer and vehicular communications paradigms have brought the task of estimating traffic state parameters in real-time within reach.

This has led to the main research question of this thesis: Can a vehicle accurately estimate traffic parameters using onboard resources shared through CV technology in a lightweight manner without utilizing centralized or roadside infrastructure?

In 1954 Wardrop and Charlesworth proposed the Moving Observer method to measure traffic parameters based on an observed number of vehicle passes. We start by proposing methods for detecting …

Towards Dynamic Vehicular Clouds, Aida Ghazizadeh

Computer Science Theses & Dissertations

Motivated by the success of the conventional cloud computing, Vehicular Clouds were introduced as a group of vehicles whose corporate computing, sensing, communication, and physical resources can be coordinated and dynamically allocated to authorized users. One of the attributes that set Vehicular Clouds apart from conventional clouds is resource volatility. As vehicles enter and leave the cloud, new computing resources become available while others depart, creating a volatile environment where the task of reasoning about fundamental performance metrics becomes very challenging. The goal of this thesis is to design an architecture and model for a dynamic Vehicular Cloud built on …

Gesture Based Control Of Semi-Autonomous Vehicles, Brian Sanders

Computational Modeling & Simulation Engineering Theses & Dissertations

The objective of this investigation is to explore the use of hand gestures to control semi-autonomous vehicles, such as quadcopters, using realistic, physics based simulations. This involves identifying natural gestures to control basic functions of a vehicle, such as maneuvering and onboard equipment operation, and building simulations using the Unity game engine to investigate preferred use of those gestures. In addition to creating a realistic operating experience, human factors associated with limitations on physical hand motion and information management are also considered in the simulation development process. Testing with external participants using a recreational quadcopter simulation built in Unity was …

A Design Of Inductive Coupling Wireless Power Transfer System For Electric Vehicle Applications, Sarika Reddy Daida

Electrical & Computer Engineering Theses & Dissertations

This research focuses on the study of using an inductive-coupled Wireless Power Transfer (WPT) system for electric vehicle charging applications in Medium Voltage DC (MVDC) power networks. Implementing WPT in Electric Vehicles (EVs) can provide a convenient alternative charging option, versus static charging in a station that would take hours. Also, it can prevent the potential of electrocution hazards that might occur due to the usage of physical medium like wires in EV charging. Even though inductive coupling has been applied in some applications of WPT, it is still not efficient enough to transfer high power at the kilowatts level …

A Simulation-Based Layered Framework Framework For The Development Of Collaborative Autonomous Systems, Ioannis Sakiotis

Computational Modeling & Simulation Engineering Theses & Dissertations

The purpose of this thesis is to introduce a simulation-based software framework that facilitates the development of collaborative autonomous systems. Significant commonalities exist in the design approaches of both collaborative and autonomous systems, mirroring the sense, plan, act paradigm, and mostly adopting layered architectures. Unfortunately, the development of such systems is intricate and requires low-level interfacing which significantly detracts from development time. Frameworks for the development of collaborative and autonomous systems have been developed but are not flexible and center on narrow ranges of applications and platforms. The proposed framework utilizes an expandable layered structure that allows developers to define …

Investigating The Relationship Between Latent Driving Patterns And Traffic Safety Using Smartphone-Based Mobile Sensor Data, Kenneth Wynne

Civil & Environmental Engineering Theses & Dissertations

Crash frequency modelling has been used in the past as an attempt to quantify the expected number of crashes occurring on a certain segment of roadway given a set of variables and factors describing the roadway segment and the traffic along that segment. These models are referred to as the Safety Performance Functions (SPFs) in the Highway Safety Manual (HSM). In past studies, these SPFs have focused primarily on roadway geometric information along with limited traffic exposure data such as traffic volume. Alternate data sources for probe vehicle data are increasingly available and this research sought to exploit this new …

Use Of A Rolling Road System In Crosswind Conditions, Mau-Kuo Chen

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel testing continues to play an important role in vehicle aerodynamic development. Accurate results are strongly associated with whether the wind tunnel can closely simulate the on-road conditions, including the Reynolds number and all boundary conditions. Rolling road systems (or moving belts) have been a successful tool for many auto makers and racing teams to simulate the relative motion between the stationary vehicle model and the floor in the test section. The mechanism of the rolling road system is simple, but how it affects the adjacent flow field and how this flow interacts with the flow underneath the vehicle …

Tdma Slot Reservation In Cluster-Based Vanets, Mohammad Salem Almalag

Computer Science Theses & Dissertations

Vehicular Ad Hoc Networks (VANETs) are a form of Mobile Ad Hoc Networks (MANETs) in which vehicles on the road form the nodes of the network. VANETs provide several services to enhance the safety and comfort of drivers and passengers. These services can be obtained by the wireless exchange of information among the vehicles driving on the road. In particular, the transmission of two different types of messages, safety/update and non-safety messages.

The transmission of safety/update message aims to inform the nearby vehicles about the sender's current status and/or a detected dangerous situation. This type of transmission is designed to …

Modeling, Identification, Validation And Control Of A Hybrid Maglev Ball System, Ahmed Elhussein E. Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, the electrodynamics of a single axis hybrid electromagnetic suspension Maglev system was modeled and validated by applying it to a single axis hybrid maglev ball experiment. By exploring its linearized model, it was shown that the single axis hybrid Maglev ball has inherently unstable dynamics. Three control scenarios were explored based on the linearized model; (1) Proportional, Deferential (PD) control, (2) Proportional, Deferential, Integral (PID) and (3) PID controller with pre-filtering. This thesis has shown that a PID controller with a pre-filtering technique can stabilize such a system and provide a well-controlled response.

A parametric system identification …

Interface Circuit For A Multiple-Beam Tuning-Fork Gyroscope With High Quality Factors, Ren Wang

Mechanical & Aerospace Engineering Theses & Dissertations

This research work presents the design, theoretical analysis, fabrication, interface electronics, and experimental results of a Silicon-On-Insulator (SOI) based Multiple-Beam Tuning-Fork Gyroscope (MB-TFG). Based on a numerical model of Thermo-Elastic Damping (TED), a Multiple-Beam Tuning-Fork Structure (MB-TFS) is designed with high Quality factors (Qs) in its two operation modes. A comprehensive theoretical analysis of the MB-TFG design is conducted to relate the design parameters to its operation parameters and further performance parameters. In conjunction with a mask that defines the device through trenches to alleviate severe fabrication effect on anchor loss, a simple one-mask fabrication process is employed to implement …

A Framework For Dynamic Traffic Monitoring Using Vehicular Ad-Hoc Networks, Mohammad Hadi Arbabi

Computer Science Theses & Dissertations

Traffic management centers (TMCs) need high-quality data regarding the status of roadways for monitoring and delivering up-to-date traffic conditions to the traveling public. Currently this data is measured at static points on the roadway using technologies that have significant maintenance requirements. To obtain an accurate picture of traffic on any road section at any time requires a real-time probe of vehicles traveling in that section. We envision a near-term future where network communication devices are commonly included in new vehicles. These devices will allow vehicles to form vehicular networks allowing communication among themselves, other vehicles, and roadside units (RSUs) to …

Exploring The Effects Of Cooperative Adaptive Cruise Control In Mitigating Traffic Congestion, Georges M. Arnaout

Engineering Management & Systems Engineering Theses & Dissertations

The aim of this research is to examine the impact of CACC (Cooperative Adaptive Cruise Control) equipped vehicles on traffic-flow characteristics of a multilane highway system. The research identifies how CACC vehicles affect the dynamics of traffic flow on a road network and demonstrates the potential benefits of reducing traffic congestion due to stop-and-go traffic conditions. An agent-based traffic simulation model is developed specifically to examine the effect of these intelligent vehicles on the traffic flow dynamics. Traffic performance metrics characterizing the evolution of traffic congestion throughout the road network, are analyzed. Different CACC penetration levels are studied.

The positive …

Data Aggregation And Dissemination In Vehicular Ad-Hoc Networks, Khaled Ibrahim

Computer Science Theses & Dissertations

Vehicular Ad-Hoc Networks (VANETs) are a fast growing technology that many governments and automobile manufacturers are investing in to provide not only safer and more secure roads, but also informational and entertainment-based applications for drivers. The applications developed for VANETs can be classified into multiple categories (safety, informational, entertainment). Most VANET applications, regardless of their category, depend on having certain vehicular data(vehicular speed, X position and Y position) available. Although these applications appear to use the same vehicular data, the characteristics of this data (i.e., amount, accuracy, and update rate) will vary based on the application category. For …

Providing Location Security In Vehicular Ad Hoc Networks, Gongjun Yan

Computer Science Theses & Dissertations

Location is fundamental information in Vehicular Ad-hoc Networks (VANETs). Almost all VANET applications rely on location information. Therefore it is of importance to ensure location information integrity, meaning that location information is original (from the generator), correct (not bogus or fabricated) and unmodified (value not changed). We present validation mechanisms to provide location integrity for VANETs. In the initial mechanism, we assume that all vehicles are equipped with a radar, a GPS receiver, and a transceiver. Since radar has a limited radar range and transceiver has a limited transmission range, we build network cells as a security unit as well …

Stability Analysis, Modeling, Simulation And Experimental Testing Of An Ems Maglev System With Structural Flexibility, Aravind M. Hanasoge

Mechanical & Aerospace Engineering Theses & Dissertations

Vehicle-guideway interaction studies of Magnetically Levitated (Maglev) vehicles indicate that structural flexibility can adversely affect the overall stability and performance of such systems. This is one of the reasons why guideways are generally made very rigid. This in turn leads to increased cost of the overall system since guideway construction forms a significant portion of the overall cost. In this dissertation, the influence of structural flexibility on the stability of Electromagnetic Suspension (EMS) Maglev systems is studied. It is shown how inherently unstable and flexible structure EMS Maglev systems can achieve guaranteed stability by using collocated actuators and sensors, along …

External Aerodynamics Of Heavy Ground Vehicles: Computations And Wind Tunnel Testing, Ilhan Bayraktar

Mechanical & Aerospace Engineering Theses & Dissertations

Aerodynamic characteristics of a ground vehicle affect vehicle operation in many ways. Aerodynamic drag, lift and side forces have influence on fuel efficiency, vehicle top speed and acceleration performance. In addition, engine cooling, air conditioning, wind noise, visibility, stability and crosswind sensitivity are some other tasks for vehicle aerodynamics. All of these areas benefit from drag reduction and changing the lift force in favor of the operating conditions. This can be achieved by optimization of external body geometry and flow modification devices. Considering the latter, a thorough understanding of the airflow is a prerequisite.

The present study aims to simulate …

Minimizing Post-Production Weight Growth In Tanks Using A Decision Analysis Model, Michael F. Cochrane

Engineering Management & Systems Engineering Theses & Dissertations

Post-production weight growth of tanks is an historic problem for the military. Tanks are difficult to transport because of their weight, and post-production modifications tend to cause this weight to increase over the lifecycle of the tank. In this thesis, a computer model is constructed which uses influence diagrams to model tank weight growth as a probabilistic process. Historical weight data for the MI Abrams tank program is used to derive probabilities for the model. The model is used to predict tank weight growth over both the short and long term with the goal of understanding more about how and …

Application Of Reanalysis Techniques For Pattern Design Of Spot Welds, Young San Kim

Mechanical & Aerospace Engineering Theses & Dissertations

Extensive benchmarking on competitive cars has shown that the durability of vehicles, assembly-induced variations, and assembly cost are directly related to the quality and number of spot welds. On most luxury cars, approximately 4,500 to 5,000 spot welds are found. On less expensive cars, the range is from 3,500 to 4,500. These cars usually inherit more noise, rattles, squeaks, and other quality-related problems. These problems have motivated the search for a new capability to systematically place welds in the most critical areas, with a minimum number of welds for car bodies, while satisfying all performance requirements (e.g., stiffness, stress distribution, …

Shape Sensitivity Analysis And Optimization Of Skeletal Structures And Geometrically Nonlinear Solids, Ching-Hung Chuang

Mechanical & Aerospace Engineering Theses & Dissertations

Formulations and computational schemes for shape design sensitivity analysis and optimization have been developed for both skeletal structures and geometrically nonlinear elastic solids. The continuum approach, which is based on the weak variational form of the governing differential equation and the concept of the material derivative, plays a central role in such a development.

In the first part of this work, the eigenvalue and eigenvector sensitivity equations for skeletal structures are derived with respect to configuration variables of joint and support locations. This derivation is done by the domain method as well as the boundary method. The discrete approach for …