Automotive Engineering Commons^™

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Multi-Robot Symbolic Task And Motion Planning Leveraging Human Trust Models: Theory And Applications, Huanfei Zheng

All Dissertations

Multi-robot systems (MRS) can accomplish more complex tasks with two or more robots and have produced a broad set of applications. The presence of a human operator in an MRS can guarantee the safety of the task performing, but the human operators can be subject to heavier stress and cognitive workload in collaboration with the MRS than the single robot. It is significant for the MRS to have the provable correct task and motion planning solution for a complex task. That can reduce the human workload during supervising the task and improve the reliability of human-MRS collaboration. This dissertation relies …

Significance Of The Vehicle Front Design And Gait Postures On Traumatic Brain Injuries Sustained By Different Pedestrian Populations During Car-To-Pedestrian Collisions (Cpcs) - A Computational Approach, Thava Kalishwara Kumar Gunasekaran

Electronic Thesis and Dissertation Repository

With the increasing prevalence of traumatic brain injuries (TBIs) in road traffic accidents (RTAs), it was identified that the shape of the vehicle's front end and pedestrian postures prior to impact significantly influence pedestrian head injuries. However, the effect of vehicle front shape parameters and gait postures on TBIs sustained in car-to-pedestrian collisions (CPCs) has yet to be quantified. This study used a computational approach to analyze the effect of vehicle shape parameters and pedestrian gait postures on pedestrian TBI risks across a diverse pedestrian population with varying body sizes. Our findings indicate that vehicle shape parameter such as BLEH …

Research On The Methods Of Ship's Autonomous Collision Avoidance In Complex Environment, Hongguang Lyu

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Development Of Mbd Model And Analysis Methodology For Vehicle Design, Alfonso Christopher Ponce

Mechanical Engineering ETDs

This thesis is to provide a new methodology that considers the effects the chassis applies during dynamic load to the suspension and the handling characteristics of a road course vehicle. A methodology in which is described in detail as well as an applied demonstration where literature before this thesis, lacks in replication and serves to establish a basis for multi-body dynamic analysis in this area. Two models to be created, rigid and flexible, and to compare each other to study the effects the chassis torsional stiffness has during load transfer. Ultimately, to assist in the design of a vehicle that …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Lithium And The Foreseeable Future, Paolo Vargas

Mechanical Engineering Undergraduate Honors Theses

This paper aims to clarify the uncertainties regarding worldwide lithium resource availability in the years to come. Previous studies made on the subject are presented with some ambiguity and this work intends to fill the gaps. The information and data presented throughout this script with respect to global lithium resources and reserves are mostly based on data released by the United States Geological Survey (USGS). Lithium resource availability in the future is a point of paramount significance primarily for the automotive, portable electronics, and the power generation industry. Since, a change of supply would ultimately affect the price of lithium, …

Mechanical Characterization And Shear Test Comparison For Continuous-Fiber Polymer Composites, Matthew Crossan

Electronic Thesis and Dissertation Repository

As fiber-reinforced composites continue to be used in a wide-range of high performance structures, more detailed understanding and accurate prediction of stress-strain behaviour is necessary to improving designs and reducing costs. This thesis compares the experimental behaviour of a continuous fiber polymer composite of carbon fiber and epoxy resin using Digital Image Correlation to analytical and theoretical predictions. Furthermore, an in-depth analysis of shear testing methods reveals the advantages and limitations of different testing standards. Finally, the limitations of the Iosipescu Shear test (ASTM 5379) fixture to break high-strain-to-failure composites in comparison to the V-notched Rail Shear Fixture (ASTM 7078) …

Manufacturing A Composite Wheel Prototype Using 3d Printed Molds, Steven Thuening

All Graduate Theses, Dissertations, and Other Capstone Projects

Throughout the evolution of high performance racing, a large emphasis has been on reducing the weight of the vehicle in order to improve its performance. Over the years, new designs and materials have been introduced reducing weight in a variety of different locations. Comparing weight reduced in different areas has shown that some areas are more valuable to reduce than others are. Perhaps one of the most beneficial locations are the wheels. This is because the mass of the wheel is considered unsprung and rotational. Because of this, large improvements towards the reduction of wheel mass have been developed in …

Analyses Of Densely Crosslinked Phenolic Systems Using Low Field Nmr, Jigneshkumar Patel

Doctoral Dissertations

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multi-components, especially for the crosslinking of rigid high-performance materials. In these reactions, miscibility is crucial for curing efficiency. This miscibility is typically enhanced by adding a third component, a plasticizer. For the reaction of the highly crystalline crosslinking agent hexamethylenetetramine (HMTA) with a strongly hydrogen-bonded phenol formaldehyde resin, furfural has been traditionally used as the plasticizer. However, the reason for its effectiveness is not clear. In this doctoral thesis work, miscibility and crosslinking efficiency of plasticizers in phenolic curing reactions are studied by thermal analysis and spectroscopic …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Asme Baja Rc Car Drivetrain, Walter Lackey

All Undergraduate Projects

The ASME Baja car is a student built radio controlled car, which will compete with other schools in a variety races. The drivetrain aspect of the car must smoothly transfer power from the motor to the rear wheels of the car. The drivetrain must be designed in collaboration with the other team member’s suspension system to avoid interference. The majority of the parts in the drivetrain are purchased parts intended for various applications. These parts were chosen based on their proximity to the optimal calculated values. Power flows from the electric motor through a single gear reduction, then through a …

Easily Verifiable Controller Design With Application To Automotive Powertrains, Mohammad Reza Amini

Dissertations, Master's Theses and Master's Reports

Bridging the gap between designed and implemented model-based controllers is a major challenge in the design cycle of industrial controllers. This gap is mainly created due to (i) digital implementation of controller software that introduces sampling and quantization imprecisions via analog-to-digital conversion (ADC), and (ii) uncertainties in the modeled plant’s dynamics, which directly propagate through the controller structure. The failure to identify and handle these implementation and model uncertainties results in undesirable controller performance and costly iterative loops for completing the controller verification and validation (V&V) process.

This PhD dissertation develops a novel theoretical framework to design controllers that are …

The Impact Of Active Aerodynamics On Motorcycles Using Computational Fluid Dynamics Simulations, Aditya Sripathi

All Graduate Theses, Dissertations, and Other Capstone Projects

Motorcycles are mostly utilized by commuters whose requirements are cheap and affordable transportation from point A to point B. Motorcycles also provide means to tour various places and have a leisure time for the majority of motorcyclists. Unfortunately, with pros also come cons such as accidents which are disabling or life-taking. According to motorcycle crash statistics produced every year, the majority of motorcycle crashes are caused due to facing unexpected obstacles in the path causing collisions due to insufficient braking time. Thus, this thesis serves as a mean to overcome this issue and provide a technological solution to the world …

Human-Assisted Fluid Power Vehicle, Aaron Huntoon

Honors Theses

The rising cost of energy has prompted industrial and technology companies to research and implement renewable or green energy sources in every aspect of their business. This green technology can consist of sources such as: solar, wind, fluid, or others to create energy from renewable sources. The use of these various sources reduces the pollution associated with standard methods of energy development, and it will ultimately drive costs down to benefit the general population. One of the largest benefactors to the use of renewable energy sources is the transportation industry. Billions of people rely on various modes of transportation every …

Integration And Testing Of An Advanced Conformable Cng Tank In A Full-Sized Light-Duty Pickup, Abayomi Famuyiwa

Dissertations, Master's Theses and Master's Reports

Michigan Technological University is collaborating with Southwestern Energy and REL Inc. to develop and integrate a compressed natural gas (CNG) matrix tank that enables efficient packaging, increases range, and reduced cost for CNG vehicle applications. The vehicle being used in this project is a light-duty pickup truck to take advantage of the open space underneath the body and bed of the vehicle. With today’s cylindrical CNG tanks consuming cargo space, a solution is to develop a tank capable of being shaping to the underbody of the truck to free cargo space. University faculty and graduate students utilizes Finite Element Analysis …

Analysis Of A Carbon Fiber Reinforced Polymer Impact Attenuator For A Formula Sae Vehicle Using Finite Element Analysis, John T. Rappolt

Master's Theses

The Hashin failure criteria and damage evolution model for laminated fiber reinforced polymers are explored. A series of tensile coupon finite element analyses are run to characterize the variables in the physical model as well as modeling techniques for using an explicit dynamic solver for a quasi-static problem. An attempt to validate the model on an axial tube crush is presented. It was found that fiber buckling was not occurring at the impactor-tube interface. Results and speculation as to why the failure initiation is incorrect are discussed. Lessons learned from the tube crush are applied successfully to the quasi-static Formula …

Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage

All Graduate Theses, Dissertations, and Other Capstone Projects

This study was conducted to create a bio-composite with a porous structure using the binder-jet printing additive manufacturing process. The samples were printed by changing the parameters such as layer thickness, roller speed, sintering time and sintering temperature of the X1-Lab binder jet additive manufacturing printer. The samples were printed 80% stainless steel 316 mixed with 20% Calcium Phosphate Tribasic by volume. Eight experiments were attempted to print according to the fractional factorial design of experiment. The effects of changing parameters on the mechanical properties of the new bio-composite was tested using ASTM E-09 compressive strength standards. The compression testing …