Structures and Materials Commons^™

Aeroelastic Analysis Of Small-Scale Aircraft, Kent Roberts

Master's Theses

The structural design of flight vehicles is a balancing act between maximizing loading capability while minimizing weight. An engineer must consider not only the classical static structural yielding failure of a vehicle, but a variety of ways in which structural deformations can in turn, affect the loading conditions driving those deformations. Lift redistribution, divergence, and flutter are exactly such dynamic aeroelastic phenomena that must be properly characterized during the design of a vehicle; to do otherwise is to risk catastrophe. Relevant within the university context is the design of small-scale aircraft for student projects and of particular consideration, the DBF …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

University of New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Modal Characterization And Structural Dynamic Response Of A Crane Fly Forewing, Jose E. Rubio

University of New Orleans Theses and Dissertations

This study describes a method for conducting the structural dynamic analysis of a crane fly (family Tipulidae) forewing under different airflow conditions. Wing geometry is captured via micro-computed tomography scanning. A finite element model of the forewing is developed from the reconstructed model of the scan. The finite element model is validated by comparing the natural frequencies of an elliptical membrane with similar dimensions of the crane fly forewing to its analytical solution. Furthermore, a simulation of the fluid-structure interaction of the forewing under different airflows is performed by coupling the finite element model of the wing with a …

Boundary Layer Influences On The Subsonic Near-Wake Of A Family Of Three-Dimensional Bluff Bodies, Charles Willliam Alcorn

Mechanical & Aerospace Engineering Theses & Dissertations

A study is reported on subsonic bluff body near-wake flows. It has been determined that one family of bluff bodies, namely slanted-base ogive cylinders, can experience either a closed recirculating near-wake, or a longitudinal vortex near-wake depending on the base slant-angle and the Reynolds number. This suggests a dependence of near-wake parameters on the state of the boundary layer ahead of separation. This report addresses the influence of the boundary layer on the near-wake of slanted-base bluff bodies. Experiments were conducted in two facilities, the 6-inch Magnetic Suspension and Balance System (MSBS) at NASA Langley Research Center and the Old …