Aerodynamics and Fluid Mechanics Commons^™

Stratospheric Glider Measurements Of Atmospheric Parameters, Anisa Haghighi

Theses and Dissertations--Mechanical Engineering

In June 2021 a series of high altitude flights were conducted in Spaceport America, NM, using a balloon launched Uncrewed Aircraft System (UAS) to assess its capability to conduct measurements of various atmospheric properties and study turbulence in the troposphere and lower stratosphere. This UAS descends using an automated flight trajectory. The instruments aboard included a NASA-developed infrasonic microphone to evaluate its remote turbulence detection capabilities and a five-hole probe capable of measuring the in situ wind vector. Also on board were temperature, humidity and wind profile sensors. This document focuses on the atmospheric properties measured at high altitudes, the …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

A Decoupled Engineering Methodology For Accurate Prediction Of Ablative Surface Boundary Conditions In Thermal Protection Systems, Justin Cooper

Theses and Dissertations--Mechanical Engineering

The main objective of the present work is to demonstrate a method for prediction of aerothermal environments in the engineering design of hypersonic vehicles as an alternative to the current heritage method. Flat plate and stagnation point boundary layer theory require multiple assumptions to establish the current engineering paradigm. Chief among these assumptions is the similarity between mass and heat transfer. Origins of these assumptions are demonstrated and their relationship to conservative engineering design is analyzed, as well as conditions where they possibly break down. An alternative approach for assessing aerothermal environments from the fluid domain is presented, which permits …

Experimental Investigation Of Roughness And Blowing Effects Over Ablator-Like Surfaces, Colby Borchetta

Theses and Dissertations--Mechanical Engineering

Two separate experiments using PIV were carried out to investigate the effects of
roughness and blowing over surfaces geometrically similar to ablation materials used for atmospheric re-entry. The first, water tunnel experiments, employed a dimpled surface similar to AVCOAT, while the second set was completed in a wind tunnel with a material similar to PICA. For the first set, the flow with blowing becomes destabilized, and more disorganized. The blowing disrupts the relatively simple vorticity shedding process and significantly modifies momentum transport via interaction of detached structures. Flow structure and their modifications were examined with a sPOD analysis. The focus …

Numerical And Scaling Study On Application Of Inkjet Technology To Automotive Coating, Masoud Arabghahestani Dr.

Theses and Dissertations--Mechanical Engineering

A thorough literature review identified lack of precision control over quality of droplets generated by the currently available industrial sprayers and a growing need for higher quality droplets in the coating industry. Particularly, lack of knowledge and understanding in continuous inkjets (CIJ) and drop-on-demand (DOD) technologies is identified as significant. Motivated by these needs, this dissertation is dedicated to computational fluid dynamics (CFD) and scaling studies to improve existing inkjet technologies and develop new designs of efficient coating with single and/or multiple piezoelectric sensors to produce on-demand droplets. This dissertation study aims at developing a new DOD type coating technology, …

Modeling Thin Layers In Material Response Solvers, Christen Setters

Theses and Dissertations--Mechanical Engineering

Thermal Protection Systems (TPS) are a necessary component for atmospheric entry. Most TPS contain thin layers of various materials such as ceramic coatings, pore sealers and bonding agents. When modeling TPS, these thin layers are often neglected due to the difference in scale between the TPS (centimeters) and the thin layers (micrometers). In this study, a volume-averaging flux-conservation method is implemented in the governing equations of a finite volume material response code. The model proposes the addition of a volume and area fraction coefficient which utilizes a weighted-averaging between the amount of thin layer and heat shield material in a …

Turbulence Suppression In An Axially Rotating Pipe, Alyn J. Smith

Theses and Dissertations--Mechanical Engineering

The phenomenon of turbulence suppression in a rotating pipe flow system has been well documented by past research and experimentation. Despite this, the methods that drive this phenomenon have not yet been effectively characterized, especially at higher Reynolds numbers. While many experiments have been performed to better understand swirling turbulent pipe flow, a difficulty that arises is how to test for high levels of rotation without reducing the Reynolds number. This thesis documents the design and construction of a new pressurized pipe flow system at the University of Kentucky aimed at achieving high Reynolds numbers without causing a reduction in …

Measurements Of Wind Turbine Wake Evolution And Trajectory During Morning Boundary Layer Transition And Under Wake Steering Conditions Via Unmanned Aerial Vehicles, Stewart Nelson

Theses and Dissertations--Mechanical Engineering

In July of 2019, a flight campaign was conducted using semi-autonomous Unmanned Aerial Vehicles (UAVs) at the Port Alma Kruger Energy wind farm in Ontario, Canada, to study various aspects of wind turbine wake evolution. Horizontal transects across the wakes were measured using modified fixed-wing aircraft fitted with a five-hole probe to measure the wind velocity vector. Reference boundary layer conditions were measured by an octocopter with an assortment of mounted sensors flying vertical profiles upstream of the turbines. Three experiments were conducted during the campaign, which consisted of a study on wake behavior during the morning boundary layer transition, …

A Computational Fluid-Structure Interaction Method For Simulating Supersonic Parachute Inflation, Jonathan Boustani

Theses and Dissertations--Mechanical Engineering

Following the successful landing of the Curiosity rover on the Martian surface in 2012, NASA/JPL conducted the low-density supersonic decelerator (LDSD) missions to develop large diameter parachutes to land the increasingly heavier payloads being sent to the Martian surface. Unexpectedly, both of the tested parachutes failed far below their design loads. It became clear that there was an inability to model and predict loads that occur during supersonic parachute inflation. In this dissertation, a new computational method that was developed to provide NASA with the capability to simulate supersonic parachute inflation is presented and validated. The method considers the loose …

Flame Stabilization Of A Premixed Jet In Vitiated Coflow, Tyler Owens

Theses and Dissertations--Mechanical Engineering

Premixed staged combustion in gas turbine engines can reduce emissions by lowering peak flame temperatures but can also lead to different stability characteristics when compared to traditional combustors. High pressure ratio and subsequently high temperatures can lead to conditions suitable for both autoignition and premixed flame propagation in an environment where spatial fuel/air variations are present.

An experimental facility which issues a premixed jet into a coflowing vitiated mixture was studied to examine the stability behavior, resulting in a lifted flame. The effective ignition delay observed flame was much greater than homogeneous ignition delay calculations for the same conditions. It …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Intermittency Effects On The Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah Falih Habeeb Alhamdi

Theses and Dissertations--Mechanical Engineering

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions of external wall-bounded flow.

Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length-scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions, due to the imperfect characterization of the upper bound of the inertial cascade by the integral length-scale. When a length-scale based on Townsend's …

Wing-Tip Vortex Evolution In Turbulence, Hari Charan Ghimire

Theses and Dissertations--Mechanical Engineering

Planar and stereo particle image velocimetry measurements were conducted of a wing-tip vortex decaying in free-stream turbulence in order to understand the evolution of a vortex and its decay mechanism. The vortex decayed faster in the presence of turbulence. The decay of the circulation was found to be almost entirely due to a decrease in circulation of the vortex core, caused by the relative decrease in peak tangential velocity without a corresponding increase in core radius. These events were found to be connected with the stripping of core fluid from the vortex core. The increased rate of decay of the …

Verification And Validation Studies For The Kats Aerothermodynamics And Material Response Solver, Olivia Schroeder

Theses and Dissertations--Mechanical Engineering

Modeling the atmospheric entry of spacecraft is challenging because of the large number of physical phenomena that occur during the process. In order to study thermal protection systems, engineers rely on high fidelity solvers to provide accurate predictions of both the thermochemical environment surrounding the heat shield, and its material response. Therefore, it is necessary to guarantee that the numerical models are correctly implemented and thoroughly validated. In recent years, a high-fidelity modeling tool has been developed at the University of Kentucky for the purpose of studying atmospheric entry. The objective of this work is to verify and validate this …

Multiphase Interaction In Low Density Volumetric Charring Ablators, Ali D. Omidy

Theses and Dissertations--Mechanical Engineering

The present thesis provides a description of historical and current modeling methods with recent discoveries within the ablation community. Several historical assumptions are challenged, namely the presence of water in Thermal Protection System (TPS) materials, presence of coking in TPS materials, non-uniform elemental production during pyrolysis reactions, and boundary layer gases, more specifically oxygen, interactions with the charred carbon interface.

The first topic assess the potential effect that water has when present within the ablator by examining the temperature prole histories of the recent flight case Mars Science Laboratory. The next topic uses experimental data to consider the instantaneous gas …

Data-Driven Adaptive Reynolds-Averaged Navier-Stokes K - Ω Models For Turbulent Flow-Field Simulations, Zhiyong Li

Theses and Dissertations--Mechanical Engineering

The data-driven adaptive algorithms are explored as a means of increasing the accuracy of Reynolds-averaged turbulence models. This dissertation presents two new data-driven adaptive computational models for simulating turbulent flow, where partial-but-incomplete measurement data is available. These models automatically adjust (i.e., adapts) the closure coefficients of the Reynolds-averaged Navier-Stokes (RANS) k-ω turbulence equations to improve agreement between the simulated flow and a set of prescribed measurement data.

The first approach is the data-driven adaptive RANS k-ω (D-DARK) model. It is validated with three canonical flow geometries: pipe flow, the backward-facing step, and flow around an airfoil. For all 3 test …

Comparisons Of Ablator Experimental Performance To Response Modeling And Effects Of Water Phase Transition In Porous Tps Materials, David L. Smith

Theses and Dissertations--Mechanical Engineering

The Mars Science Laboratory Entry Descent and Landing Instrumentation (MEDLI) project performed extensive arc jet tests for development, qualification, and calibration of instrumented heat shield plugs. These plugs each contained several thermocouples for recording near-surface and in-depth temperature response of the Phenolic Impregnated Carbon Ablator (PICA) heat shield. The arc jet test results are entered into a comprehensive database so that broad trends across the test series can be compared. One method of analysis is to compare with ablator material response calculations and solve the in-depth heat conduction equations. Using the near-surface thermocouple measurements as a boundary condition in numerical …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Experimental Investigation Of Wall Shear Stress Modifications Due To Turbulent Flow Over An Ablative Thermal Protection System Analog Surface, Jacob Helvey

Theses and Dissertations--Mechanical Engineering

Modifications were made to the turbulent channel flow facility to allow for fully developed rough quasi-2D Poiseuille flow with flow injection through one surface and flow suction through the opposing surface. The combination of roughness and flow injection is designed to be analogous to the flow field over a thermal protection system which produces ablative pyrolysis gases during ablation. It was found that the additional momentum through the surface acted to reduce skin friction to a point below smooth-wall behavior. This effect was less significant with increasing Reynolds number. It was also found that the momentum injection modified the wake …

Modeling Of Spallation Phenomenon In An Arc-Jet Environment, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical Engineering

Space vehicles, while entering the planetary atmosphere, experience high loads of heat. Ablative materials are commonly used for a thermal protection system, which undergo mass removal mechanisms to counter the heat rates. Spallation is one of the ablative processes, which is characterized by the ejection of solid particles from the material into the flow. Numerical codes that are used in designing the heat shields ignore this phenomenon. Hence, to evaluate the effectiveness of spallation phenomenon, a numerical model is developed to compute the dynamics and chemistry of the particles. The code is one-way coupled to a CFD code that models …

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Experimental Characterization Of Roughness And Flow Injection Effects In A High Reynolds Number Turbulent Channel, Mark A. Miller

Theses and Dissertations--Mechanical Engineering

A turbulent channel flow was used to study the scaling of the combined effects of roughness and flow injection on the mean flow and turbulence statistics of turbulent plane Poiseuille flow. It was found that the additional momentum injected through the rough surface acted primarily to enhance the roughness effects and, with respect to the mean flow, blowing produced similar mean flow effects as increasing the roughness height. This was not found to hold for the turbulence statistics, as a departure from Townsend’s hypothesis was seen. Instead, the resulting outer-scaled streamwise Reynolds stress for cases with roughness and blowing deviated …

Near Wall Shear Stress Modification Using An Active Piezoelectric Nanowire Surface, Christopher R. Guskey

Theses and Dissertations--Mechanical Engineering

An experimental study was conducted to explore the possible application of dynamically actuated nanowires to effectively disturb the wall layer in fully developed, turbulent channel flow. Actuated nanowires have the potential to be used for the mixing and filtering of chemicals, enhancing convective heat transfer and reducing drag. The first experimental evidence is presented suggesting it is possible to manipulate and subsequently control turbulent flow structures with active nanowires. An array of rigid, ultra-long (40 μm) TiO₂ nanowires was fabricated and installed in the bounding wall of turbulent channel flow then oscillated using an attached piezoelectric actuator. Flow velocity …

A Filter-Forcing Turbulence Model For Large Eddy Simulation Incorporating The Compressible "Poor Man's" Navier--Stokes Equations, Joshua Strodtbeck

Theses and Dissertations--Mechanical Engineering

A new approach to large-eddy simulation (LES) based on the use of explicit spatial filtering combined with backscatter forcing is presented. The forcing uses a discrete dynamical system (DDS) called the compressible ``poor man's'' Navier--Stokes (CPMNS) equations. This DDS is derived from the governing equations and is shown to exhibit good spectral and dynamical properties for use in a turbulence model. An overview and critique of existing turbulence theory and turbulence models is given. A comprehensive theoretical case is presented arguing that traditional LES equations contain unresolved scales in terms generally thought to be resolved, and that this can only …

Aerodynamics And Control Of A Deployable Wing Uav For Autonomous Flight, Michael Thamann

Theses and Dissertations--Mechanical Engineering

UAV development and usage has increased dramatically in the last 15 years. In this time frame the potential has been realized for deployable UAVs to the extent that a new class of UAV was defined for these systems. Inflatable wing UAVs provide a unique solution for deployable UAVs because they are highly packable (some collapsing to 5-10% of their deployed volume) and have the potential for the incorporation of wing shaping. In this thesis, aerodynamic coefficients and aileron effectiveness were derived from the equations of motion of aircraft as necessary parameters for autonomous flight. A wind tunnel experiment was performed …

Low Reynolds Number Flow Field Modification Via Travelling Wave Actuation Of A Vertically Aligned Wire Array Surface, John C. Calhoun

Theses and Dissertations--Mechanical Engineering

Experiments were conducted to observe the effects of an active wire surface on low-Reynolds number Poiseuille flow. The objective was to evaluate the feasibility of actuating piezoelectric nanowires into a travelling wave motion in order to reduce wall shear stress in turbulent flows. Studies have shown that travelling wave motions introduced into the bounding wall of turbulent flow can reduce wall shear stress by disrupting the formation of drag-inducing coherent vortical structures. A Reynolds number scaled flow facility was designed to represent the near-wall region of turbulent flow. A wire surface was installed in the bounding wall and dynamically actuated …