Engineering Commons^™

Experimental Study Of Condensation In Different 3d Printed Regenerators In A Thermoacoustic Cooler, Aibek Bekkulov

Theses and Dissertations

Thermoacoustics (TA) deals with the conversion of heat into sound and vice versa. Device that converts heat into acoustic work is called TA heat engine, while the device that transfers energy from a low temperature reservoir to a high temperature one by utilizing acoustic work is called TA cooler. A simple construction of TA cooler includes an acoustic speaker, a resonator tube and a regenerator stack in which the temperature gradient is being imposed. Such a TA cooler has several advantages over traditional compression/expansion cooling machine such as its simplicity of the construction, high reliability and lack of toxic refrigerants. …

Development Of Flexible Photo-Mechanoluminescent Polymeric Based Systems, Carlos Hernandez

Theses and Dissertations

The project focuses on the creation of nanofiber systems with enhanced photo-mechanoluminescent response and high mechanical flexibility to further enhance promising optical applications. Lanthanide-Polyvinyl Di-Fluoride fiber systems were created using centrifugal spinning and characterized using SEM, FTIR, XPS, DSC, XRD, and PL. Fibers luminescence response was gotten when induced by ultraviolet light and the application of an impact force.

Polymeric Pvdf Fibers For Piezoelectric Applications In Energy Harvesting, Misael E. Martinez

Theses and Dissertations

This work focuses on developing and characterizing the piezoelectric response of Cerium doped Polyvinylidene Fluoride (PVDF) fine fibers and the effects of dopants and alignment on the formation of the β-phase and consequently on the piezoelectric performance. Six sets of fiber mats were prepared varying the concentration (2.5–7.5wt%) of Cerium (III) Nitrate-Hexahydrate and Ammonium-Cerium (IV) Sulfate-Dihydrate. Fiber mats were developed using the Forcespinning® technique and the angular velocity and dopant concentration were adjusted to obtain a synergy between fiber yield and fiber diameter. Fourier Transform Infrared Spectroscopy showed a significant enhancement in the PVDF β-phase and inhibition of the non-polar …

Secondary Resonances Of Electrostatically Actuated Mems Cantilevers, Christopher I. Reyes

Theses and Dissertations

In this work the behavior of micro-electromechanical (MEMS) cantilever resonators is investigated. The cantilever resonators are electrostatically actuated with hard AC voltage resulting in nine distinct resonances cases including super and subharmonic resonances. The amplitude frequency and amplitude voltage bifurcation diagrams are obtained for each of the nine resonance cases. Reduced order models (ROMs) are developed to include one and two modes of vibration. Three different methods are used to solve the ROMs namely 1) the method of multiple scales (MMS), which is a perturbation method used for one mode of vibration, 2) the homotopy analysis method (HAM), which is …

Design Of A Bedside Walker-Cane Hybrid To Aid Senior Adults Avoid Falls During Night Walks, Jorge L. Gutierrez

Theses and Dissertations

The objective of this research and development work is to design a device to help senior adults prevent fall during night walks indoors. The problem of elders falling at a night setting was found to be caused by the multiple environmental and medical conditions. The target demographic was found to be seniors from age 65 and older. Several occupational therapists and two physical therapists were consulted to gain knowledge on elders' behavior, possible improvements on current existing devices, and feedback regarding the early prototype built. Several products and patents were researched with a lack of findings on similar products that …

An Evaluation Of Wastewater Pumping Station Facilities Using Statistical Techniques In Analyzing Each For Rehabilitation Design And To Improve The Adverse Environmental Affects, Zenaida S. Guerrero

Theses and Dissertations

The objective of this research project is to develop two evaluation models, one using excel to provide a design criterion for wastewater pumping stations in collecting design parameters and information effecting efficiency and performance of the pumps. Secondly, to develop a linear regression model for these parameters giving a correlation between dependent and independent variables to verify adverse environmental aspects. This study is based in the City of Weslaco, pertaining to the north waste watershed. The parameters collected are age, efficiency, service area, total dynamic head, existing conditions, monthly sanitary sewer over flow work orders, precipitation data, population by service …

Biomechanics Of Lower Limb During The Golf Swing Using Opensim Modeling, Andrew B. Butler

Theses and Dissertations

The purpose of this research is to investigate the biomechanics of the lower-limb using an inverse dynamics model. Experimental data, recorded by an integrated Motion Analysis – Force Plate System in the UTRGV Biomechanics Laboratory, is used to determine ground reaction forces and marker trajectories. OpenSim, a graphical musculoskeletal and computational platform, is used to model the body in three dimensions. The human body is modeled as a 12-segment linkage, consisting of 23 degrees-of-freedom and 92 muscles. The experimental data for the Biomechanics Laboratory is imported in OpenSim. Then, joint angles, generalized coordinates & accelerations of lower-limb segments, muscle forces, …

Dehumidification Water Quality Analysis Of The South Texas Gulf Of Mexico, Erik Esteban Castillo

Theses and Dissertations

This project is to introduce a new methodology for environmental research that analyzes humidity from a water treatment perspective. This is done by using a household dehumidifier, which extracts the excess humidity in a given space, to harvest the samples. The dehumidifier was used outside to act as an Atmospheric Water Generator (AWG), which is the process of extracting water from the atmosphere. When AWG is placed near shoreline, then it's classified as a Desalinated Atmospheric Water Generator (DAWG) since it extracts distilled seawater water-vapors. The methodology for DAWG analyzed turbidity in the humidity on SPI, indicating to meet {<.15} TCEQ turbidity water quality standard. The turbidity also showed to have an adverse relation to weather conditions. There is an open market in research on this topic, where the methodology for DAWG can offer answers. This project identifies DAWG as being a sustainable source of potable water for a municipality.

Security Assessment Of Select Computer Systems Under Distributed Denial Of Service Attacks Performed By Botnets, Hugo Armando Herrera Martinez

Theses and Dissertations

With the passage of time Internet connectivity has been found on more electronic devices than in previous decades. This continuous development may be perceived as a double-edged sword. While the world becomes more Internet-connected and quality of life increases, the lack of proper security protocols in some of these electronic devices permits illegitimate parties to take control of them for their own malicious purposes.

This thesis studies the impact of compromised Internet-connected devices on commonly used server operating systems: Microsoft’s Windows Server 2012 R2 Datacenter, Windows Server 2016 Datacenter, and Apple’s macOS 10.13.6 High Sierra deployed on Apple’s Mac Pro …

Exploring The Compactability And Workability Of Rap, Elizabeth Poblete

Civil Engineering Undergraduate Honors Theses

Despite its economic and environmental benefits, the widespread use of Cold In-Place Recycling (CIR) is currently inhibited, to some degree, by a lack of laboratory testing and evaluation, specifically in the areas of compactability and workability of the reclaimed mixture stabilized with asphalt emulsion. The purpose of this study was to explore the influence of admixtures in CIR using modified Superpave Gyratory Compactor (SGC) compaction metrics. The primary stabilization technique considered in this research was asphalt emulsion, an application in which asphalt binder is suspended in water, allowing it to be stored and applied at ambient temperature, rather than the …

Radiative Heat Transfer Analysis Of Railroad Bearings For Wayside Thermal Detector Optimization, James Alexandro Aranda

Theses and Dissertations

Wayside hot-box detectors (HBDs) are devices that are currently used to evaluate the health of railcar components including bearings, axles, and brakes by monitoring their temperatures. While HBDs have been instrumental in reducing some train derailments in the past few decades, the number of non-verified bearing removals has increased significantly. In general, HBDs tend to underestimate bearing temperatures in both field service and in laboratory testing, which is not surprising considering the simple two-point calibration method that is used to calibrate these devices. Because of this, different calibrations were compared and analyzed including two-point, three-point, and multi-point calibrations. Analysis of …

Synthesis And Design Of Metals Sulfide/Carbon Composite-Fibers Anodes For Lithium Ion Batteries, Jorge Lopez

Theses and Dissertations

In this study, Forcespinning is used to produce Titanium sulfide (TiS2)/carbon composite fibers for use as lithium-ion battery anodes. The high surface area to volume ratio of the composite fibers can have a high impact on the ionic and electronic conductivity of the active materials leading to improved electrochemical performance of the battery. TiS2 nanoparticles were chosen as the active materials to produce Metal-Li-alloys/C composite fibers due to their high theoretical capacity and low volume change during charge/discharge cycles. The use of a 2-D layered structure of TiS2 nanoparticles in the carbon fiber matrix can greatly accommodate more Li-ions between …

Boron Nitride Thin-Film Deposited By Rf Magnetron Sputtering, Jesus A. Valladares Gonzalez

Theses and Dissertations

Cubic Boron Nitride is considered a superhard material, its thermochemical stability makes it suitable for applications with corrosive environments and high temperatures. C-BN is grown by PDV on Si substrates. The plasma is energized via an RF source to sputter the target. The ion species in the plasma can be described by the classic electrodynamic expression . Plasma temperature is given by T = (6.2836*E/8*k). The sputter is given by the ratio of the heat transfer to the enthalpy of formation , of the target. The Hall Measurement is performed as recommended by NIST. The measurement was performed on a …

Improving Thermal-Hydraulic Performance Of Flat-Tube Louver-Fin Heat Exchangers By Eliminating Louver Gap Condensate Bridges, Alan L. Jones

Theses and Dissertations

The air side performance of heat exchangers is a well studied subject. Flat-tube louver-fin heat exchangers experience a decrease in performance when operating in dehumidifying conditions. As water vapor is pulled from the air, water condensate may create blockages between louvers. Flat-tube louver-fin heat exchanger may experience a drop in thermal-hydraulic performance by up to 50% due to blockages. The aim of this study is to make macro scale geometric changes to louver dimensions and eliminate louver condensate bridges. By eliminating louver condensate blockages, the heat exchanger should see an overall gain in thermal performance when compared to current fin …

Aligning Anatomical Knee Model With Kinematic Experimental Data To Investigate Squat Exercise, Jose Mario Salinas

Theses and Dissertations

A two-dimensional inverse dynamics anatomical model of the human knee was developed by aligning anatomical structures of the knee (taken from x-rays) with kinematic experimental data (collected from motion capture cameras). The mathematical model was used to study the forces related to the tibiofemoral and patellofemoral joints during the squat and knee extension exercises. Forces calculated by the model included: tibiofemoral contact force, patellofemoral contact force, forces generated by cruciate ligaments, quadriceps force, and patellar tendon force. Bone alignment consisted of superimposing the geometric center of the lateral femoral condyle (from x-rays) with the relative instantaneous center of rotation of …

A Systematic Approach To High Blood Pressure Risk Analysis And Healthcare Cost Reduction In Young Adults [Metodología Sistemática Para El Análisis De Riesgo Y Reducción De Costos De Servicios Médicos De Hipertensión En Adultos Jóvenes], Francisco Rafael Torres Diaz

Theses and Dissertations

The purpose of this research is to utilize publicly available data to estimate the current rate of occurrence of undiagnosed High Blood Pressure (HBP) in young adults (18 to 24 years old) and the out-of-pocket healthcare expenses associated with complications of HBP, to provide feasible alternatives to mitigate the effects on a region's economy. This has been done by building a Risk Factor Simulation Model that utilizes known HBP risk factors’ correlation to HBP, insurance coverage data, and rate of diagnosis to formulate the average Risk Factor Value for a region, which through an Annual Expected Cost Function estimates the …

Achieving Universal Liaisons And Healthcare Contact Center Centralization Through The Use Of Decision Support Tools, Jared S. Fiacco

Graduate Dissertations and Theses

Healthcare contact centers often experience a large volume of calls and traditional standardized guidelines can be difficult to follow during an active call. While more common workflows can be memorized, they change often because Healthcare is a dynamic field. Constant updates to workflows, an abundance of different processes and provider preferences, and a fast paced environment can lead Customer Service Liaisons (CSLs) to handle patient inquiries incorrectly. Active decision support tools enable a CSL to follow an updated workflow without needing to navigate through complex guidelines and emails. This research shows that contact center centralization through the use of decision …

Analysis Of Flash In Injection Molding Using Flow Simulation And Design Of Experiments, Claudia Lizette Lopez

Theses and Dissertations

This study presents a method of detecting flash by using flow simulation along with the mold processing conditions and the DOE analysis values from all input and output parameters that will be calculated. All of this would be completed in order to compare and verify the DOE and simulation results and find out if it can be applied to an actual live production molded part, in this case, the Leap char ribbon. This paper will also describe the scrap issue that is presently happening on this molded part, and what are the options that there is in order to find …

Design And Qualification Of A Robust Polyurethane Based Conformal Coating Process For Sodimms, Rajat Dhiman

Graduate Dissertations and Theses

Conformal coatings protect printed circuit board assemblies, including the electronic components that the assemblies are populated with. A variety of materials and application methods can be used to conformally coat assemblies. The process setup is crucial to repeatable process reliability. The manual spray based conformal coating is widely used. This method of application was selected due to its compatibility, affordability, and efficiency with the required application. Polyurethanes, one of the families of conformal coatings, provide resistance against abrasion, heat, and chemicals while reducing the risk of tin whiskers. In order to minimize the need for rework and create an efficient, …

Using Multifactor Inputs Bp Neural Network To Make Power Consumption Prediction, Hao Song

Graduate Dissertations and Theses

With the development of modern information and technology (IT), smart grids became one of the major components of smart cities, to take full advantage of the smart grid, the capability of intelligent scheduling and planning of electricity delivery is essential. For this purpose, researchers have investigated methodologies for power consumption prediction and demand side management (DSM). In addition, conducting a comprehensive analysis and obtaining an accurate evaluation of power consumption are the premise and basis for a more robust and efficient power grid design and transformation. Therefore, it is meaningful to explore forecasting models that are able to reflect the …

Forcespinning Of Metal Oxides And Metal Sulfides And Their Applications As Alternative Anode Materials For Lithium-Ion And Sodium-Ion Batteries, Alejandra Valdez

Theses and Dissertations

Molybdenum-Oxide/Carbon (MoO2/C) composite nanofibers were synthesized using Forcespinning method and subsequent heat treatment, for use as anode materials for lithium-ion batteries. Due to the layered structure of MoO2, the composite nanofibers are very promising for use as anode material for LIBs. The MoO2/C composite fiber anodes exhibit good electrochemical performance and cycling stability.

Multi-Objective Design Optimization Of Reverse Total Shoulder Arthroplasty To Maximize Range Of Motion And Joint Stability, Josie A. Elwell

Graduate Dissertations and Theses

Reverse total shoulder arthroplasty was developed to restore range of motion (ROM) and joint stability to patients with pre-operative conditions that are not addressed by conventional replacements. Although reverse total shoulder arthroplasty is the current gold standard for treating a range of indications, the effects of varying its design on functional outcomes of the procedure are still not well understood.

To that end, it is not yet clear which configurations, in terms of both design and surgical placement parameters, maximize range of motion and stability of the joint. It was hypothesized that there is trade-off between the two. These types …

Use Of A Triboelectric Generator For A Tunable Wideband Energy Harvester And A Threshold Shock Sensor, Daniel S. Nelson

Graduate Dissertations and Theses

The prevalence of triboelectricity as a transduction mechanism has increased rapidly in recent years. We will discuss two uses for triboelectric generators. One design is a tunable wideband energy harvester. An axial force and amplitude limiter work together to create an energy harvester that can accommodate various frequency sources and have a large operating bandwidth. The addition of the compressive axial force also softens the system, which allows for higher voltage outputs. A proof of concept of a threshold shock sensor is proposed that incorporates bi-stability along with the triboelectric effect. A clamped-clamped buckled beam will switch stable states when …

Antimicrobial Properties And Characterization Of Polymer/Composite Nanofibers, David De La Garza

Theses and Dissertations

Pathogenic bacteria have been the cause of many illnesses worldwide due to their rapid growth and reproduction in food and water. Bacteria-resistant antibiotics and kidney complications due to overuse of antibiotics has remained a large public health concern. The goal of this research project was to find an alternative by producing nanofibers that inhibit microbial growth utilizing Forcespinning technology. The Forcespinning of poly(acrylic acid) (PAA) with Single Wall Carbon Nanotubes functionalized with OH (SWCNT-OH) and Ag + flakes were carried out on solutions with different concentrations. Scanning electron microscopy was used to view fiber morphology and investigate the average nanofiber …

Computational Fluid Dynamics Modeling And In Situ Physics-Based Monitoring Of Aerosol Jet Printing Toward Functional Assurance Of Additively-Manufactured, Flexible And Hybrid Electronics, Roozbeh (Ross) Salary

Graduate Dissertations and Theses

Aerosol jet printing (AJP)—a direct-write, additive manufacturing technique—has emerged as the process of choice particularly for the fabrication of flexible and hybrid electronics. AJP has paved the way for high-resolution device fabrication with high placement accuracy, edge definition, and adhesion. In addition, AJP accommodates a broad range of ink viscosity, and allows for printing on non-planer surfaces. Despite the unique advantages and host of strategic applications, AJP is a highly unstable and complex process, prone to gradual drifts in machine behavior and deposited material. Hence, real-time monitoring and control of AJP process is a burgeoning need. In pursuit of this …

Development Of Collagen-Based Scaffolds For Differentiation Of Induced Pluripotent Stem Cells, Siteng Fang

Graduate Dissertations and Theses

Collagen hydrogel has been broadly studied and applied in engineering 3D scaffold materials in tissue engineering. A collagen hydrogel can provide cells with a porous and soft environment to proliferate and differentiate. However, lacking mechanical stiffness and shrinkage resistance made it a challenge to sustain shape and size during a long stem cell differentiation process. In addition, a cytocompatible scaffold for human induced pluripotent stem cell (iPSC)-laden culture has not been fully investigated. The goal of this study is to develop stable and biocompatible collagen-based scaffolds that are suitable for direct seeding and lineage progression of iPSCs. In this work, …

Assessing The Tensile And Fatigue Behavior Of Aerosol Jet Printed Nano Silver Particle Traces On Polyimide Substrates, Roshan Muralidharan

Graduate Dissertations and Theses

Flexible interconnects are integral to flexible hybrid electronics. Aerosol jet, inkjet or screen printing offer various advantages and disadvantages compared to electroplating, but the behavior of printed metal traces under various types of loading is very different and not yet well understood. This thesis presents an assessment of the electromechanical behavior of aerosol jet printed Nano silver particles on two common polyimide substrates, Upilex and Kapton.

There are many different aspects to electromechanical testing of flexible interconnects, but this work focuses on the effects of tension and cyclic loading. In comparison to the much more widely researched electroplated copper or …

Design And Synthesis Of Novel Nanometallic Catalysts And Electrode Materials For Green Fuel Cells, Jing Zhang

Graduate Dissertations and Theses

The United Nations formally adopted 17 sustainable development goals (SDGs) at its 2015 summit. Many of these goals addressed issues such poverty, hunger, health, education, climate-change, gender equality, water, sanitation, energy, urbanization, environment and social justice. The seventh SDG seeks to ensure access to affordable, reliable, sustainable and modern energy for all. So among all renewable forms of energy, fuel cells with high efficiency have attracted a lot of attention recently. In particular, the direct ethanol fuel cells (DEFCs) and microbial fuel cells (MFCs) are significant due to their green fuel, less waste generated and environmental friendliness. Hence the overall …

Mechanical Reinforcement Of Polyacrylamide Hydrogels Using Pristine Single-Walled Carbon Nanotubes, Wuxiang Feng

Graduate Dissertations and Theses

Hydrogels have great promise as an innovative biomedical material possessing many advantages such as high water content, porous structure, and excellent biocompatibility. Although hydrogels have been used to develop some successful applications, they commonly do not have sufficient mechanical strength required for artificial soft tissues. Here, the author fabricated reinforced PAAm hydrogels using single-walled carbon nanotubes as reinforcing materials. The fusion of SWCNTs and the PAAm matrix successfully generated SWCNTs/PAAm hybrid gels with improved mechanical strength. Moreover, the aqueous dispersion of SWCNTs used for engineering the hybrid gels remained excellent stability after two months. SEM images from previous research and …

Multifunctional Carbon Systems (Interlaminated Carbon Nanofiber Mats/ Carbon Nanotubes Polymer Composites), Homero Gonzalez Guardiola

Theses and Dissertations

Carbon nanomaterials have been an attractive topic within diverse industrial sectors given their outstanding properties for decades. One of the properties that has been calling attention is it’s shielding effectiveness (SE) for electromagnetic interference (EMI), because of the constant race of improving portable electronic and wireless communication devices among other applications. The present study, analyzes the properties of interlaminated Carbon Nanofiber (CNF) mats/Carbon Nanotubes (CNT) polymer composites, emphasizing in its capability to shield EMI. The CNF mats were developed with Polyvinyl alcohol (PVA) as a precursor and by means of the Forcespinning® technology which uses centrifugal force to create fibers …