Engineering Commons^™

Computational Fluid Dynamics Models Of Electromagnetic Levitation Experiments In Reduced Gravity, Gwendolyn Bracker

Masters Theses

Electromagnetic levitation experiments provide a powerful tool that allows for the study of nucleation, solidification and growth in a containerless processing environment. Containerless processing allows for the study of reactive melts at elevated temperatures without chemical interactions or contamination from a container. Further, by removing the interface between the liquid and its container, this processing technique allows for greater access to the undercooled region for solidification studies. However, in these experiments it is important to understand the magnetohydrodynamic flow within the sample and the effects that this fluid flow has on the experiment.

A recent solidification study found that aluminum-nickel …

Transient Flow Analysis Of A Closing Blowout Preventer Using Computational Fluid Dynamics (Cfd), Daniel Barreca

LSU Master's Theses

Reliability of blowout preventers (BOPs) is crucial for drilling and production operations. Erosion of BOP components and hydrodynamic forces on rams may cause failure of BOP elements to seal the well. Transient computational fluid dynamics (CFD) simulations of fluids within the wellbore and BOP offer quantitative and qualitative data related to this reliability during the closure of various BOP components. Since limited research has been published in transient CFD simulations of closing BOPs, this thesis discusses challenges and solutions to simulating closing blowout preventers. Single component fluids are simulated through several BOP geometries such as annular preventers, pipe rams, and …

Fire Protection System Analysis Of Warren J. Baker Center Of Science And Mathematics, Jacob Dentici

Fire Protection Engineering: Culminating Experience Project Reports

This report analyzes the different fire protection systems and features of the Warren J. Baker Center for Science and Mathematics at the California Polytechnic State University, San Luis Obispo campus. This building is used for lectures, laboratories, study spaces, faculty spaces, and storage spaces for the students and faculty at the Cal Poly campus. Typically, there are science and math courses taught within this building. The building is a 6-story structure, that is not classified as a high-rise due to the location of fire department access and has a five-story atrium located on levels 2 through 6. There are two …

The Spheres, Justin Milne

Fire Protection Engineering: Culminating Experience Project Reports

The Spheres, an architectural masterpiece surrounded by a high-rise building complex, is in the heart of South Lake Union in Seattle, Washington. The Spheres building pushes limitations in building design on all levels. With hexecontahedron panels tessellated over the façade of its three spherical glass glaze greenhouse globes, the design affords futuristic personality, alongside energy efficacy while sustaining life within the building. While building innovations within The Spheres are certainly notable within all disciplines of Architecture, Engineering, and Construction, the contents of this report refer to fire protection engineering and code consulting elements.

In meeting The Spheres' required fire safety …

Novel Low Shear 3d Bioreactor For The Scaled Production Of High Purity Human Mesenchymal Stem Cells, Andrew Burns

KGI Theses and Dissertations

Human mesenchymal stem cells are an ideal candidate for stem cell therapies. They have been researched since the 1960’s and can differentiate into many desired functional cell types without undergoing teratogenesis. However, higher yields are needed for a marketable, successful stem cell therapy. To accomplish this, cells will have to be cultured to expand them to therapeutically relevant dosages for multiple patients. Bioreactor production is an ideal method to solve this problem.

The aim of this thesis is to test and validate a novel bioreactor for the cultivation of human mesenchymal stem cells. In this work, we investigate a novel …

Direct Numerical Simulation Of Roughness Induced Hypersonic Boundary Layer Transition On A 7° Half-Angle Cone, Tara E. Crouch

Theses and Dissertations

Direct numerical simulation (DNS) computational fluid dynamic (CFD) calculations were performed on a 30° slice of 7° half-angle cones with increasing nose radii bluntness at Mach 10 while simulating a distributed roughness pattern on the cone surface. These DNS computations were designed to determine if the non-modal transition behavior observed in testing performed at the Arnold Engineering Development Center (AEDC) Hypervelocity Wind Tunnel 9 was induced via distributed surface roughness. When boundary layer transition is dominated by second mode instabilities, an increase in nose radius delays the transition location downstream. However, blunt nose experiments indicated that as the nose radius …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Wall Model Large Eddy Simulation Of A Diffusing Serpentine Inlet Duct, Ryan J. Thompson

Theses and Dissertations

The modeling focus on serpentine inlet ducts (S-duct), as with any inlet, is to quantify the total pressure recovery and ow distortion after the inlet, which directly impacts the performance of a turbine engine fed by the inlet. Accurate prediction of S-duct ow has yet to be achieved amongst the computational fluid dynamics (CFD) community to improve the reliance on modeling reducing costly testing. While direct numerical simulation of the turbulent ow in an S-duct is too cost prohibitive due to grid scaling with Reynolds number, wall-modeled large eddy simulation (WM-LES) serves as a tractable alternative. US3D, a hypersonic research …

Influence Of Leading Edge Oscillatory Blowing On Time-Accurate Dynamic Store Separation, Ryan G. Saunders

Theses and Dissertations

The primary objective of this research is to support the static and dynamic characterization and the time-accurate dynamic load data acquisition of store separation from a cavity with leading edge oscillatory blowing. Developing an understanding of, and potentially controlling, pitch bifurcation of a store release is a motivation for this research. The apparatus and data acquisition system was used in a two-part experiment to collect both static and dynamic testing data in the AFIT low speed wind tunnel in speeds of 60, 100, and 120 mph, from Reynolds numbers varying from 5.5x10⁴ to 4.6x10⁵, depending on reference …

Schlieren Imaging And Flow Analysis On A Cone/Flare Model In The Afrl Mach 6 Ludwieg Tube Facility, David A. Labuda

Theses and Dissertations

High-speed Schlieren photography was utilized to visualize flow in the Air Force Research Laboratory Mach 6 Ludwieg tube facility. A 7° half-angle cone/flare model with variable nosetip radius and flare angle options was used in the study. Testing was performed at two driver tube pressures, generating freestream Reynolds numbers of 10.0x10⁶ and 19.8x10⁶ per meter. The variable-angle flare portion of the model provided a method for adjusting the intensity of the adverse pressure gradient at the cone/flare junction. As expected from existing literature, boundary layer separation along the cone frustum occurred further upstream as the magnitude of the …

Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung

Theses and Dissertations

A recent research effort, sponsored by the Air Force Office of Scientific Research, numerically investigated the unsteady aerodynamic flow field around an oscillating, straked, delta wing. The study was centered on determining the importance of the unsteady aerodynamic forces acting as a driver for a nonlinear motion known as limit cycle oscillations. The current effort focused on creating a computational model to compare to the results of previous tests and modeling efforts and discover new information regarding the onset of LCO. The computational model was constructed using the Cartesian overset capabilities of the CREATE-AV™ fixed wing fluid dynamics solver Kestrel. …

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt

Theses and Dissertations

Wind tunnels play an indispensable role in the process of aircraft design, providing a test bed to produce valuable, accurate data that can be extrapolated to actual flight conditions. Historically, time-averaged data has made up the bulk of wind tunnel research, but modern flight design necessitates the use of dynamic wind tunnel testing to provide time-accurate data for high frequency motion. This research explores the use of a 6 degree of freedom (DOF) motion test apparatus (MTA) in the form of a robotic arm to allow models inside a subsonic wind tunnel to track prescribed trajectories to obtain time-accurate force …

Quantifying The Performance Of The Protodune Single Phase Neutrino Detector Using Computational Fluid Dynamics, Dillon Pedersen

Electronic Theses and Dissertations

The goal of this research is to provide scientifically-valid computationally generated data of the flow, thermal, and impurity data of the ProtoDUNE single phase detector. Results are compared and validated against an actual detector that is currently being utilized to collect temperature and impurity data. This research will investigate the flows inside these detection chambers using computational fluid dynamics to find approximate solutions to the governing equations of fluid mechanics. Impurity and flow data will allow researchers to determine if results collected are being obstructed by high levels of impurity. Novel approaches have been developed to strike a balance between …