Engineering Commons^™

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Reactive Archey Target Design Team "Mimic", Brandon Croyle, Jacob Boss, David Rodgers, Austin Wivell

Williams Honors College, Honors Research Projects

This design project will aim to provide archery hunters with a platform to simulate shooting at string jumping deer. String jumping refers to a spooked deer hearing the snap of a bow string and instintivly ducking up to ten inches. This often results in wounded or missed deer. We will design and build a control system that uses the sound of a bow string as a trigger to operate a mechanical target system. A sound sensor will mimic a deer’s hearing in close range hunting and then send a signal to the mechanical system to replicate the dropping motion of …

Center Lift Trailer Support Structure, Carson Corle, Anthony M. Hayes, Bryan A. Truax

Williams Honors College, Honors Research Projects

Center lift pontoon trailers have a high center of gravity, therefore have the potential for the pontoon and trailer to tip while cornering. There is need for a component to stabilize the pontoon on the trailer while towing. Different concepts of a support system were sketched to determine the best option. The characteristics that were deemed important for the support system were narrowed down to determine the best concept and the connections of the best design were sketched in greater detail. The forces that the support system would have to withstand to stabilize the pontoon on the trailer were calculated. …

Testing Of A Human Powered Vehicle, Bailey Conard, Marlee Reynolds

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, manufacturing, and testing.

The …

Recumbent Bicycle Balancing Aid, James Hager

Williams Honors College, Honors Research Projects

For our senior design project, our team will be consulting to create a balancing aid system intended for the recumbent bicycle shown below in Figure 1. The owner of the bicycle is Robert Henderson, a former United States Navy sailor from Northeast Ohio who picked up biking and skiing while he was stationed in Maine in the late 80’s. While there, he took to the mountains on the rugged terrain and brought this passion of biking back home to share with his wife, Johanna once he completed his service to his country. Biking became an integral part of the …

Carbon Fiber Racing Wheel, Megan Sanok, Melissa Furdak, Sydney Schipani

Williams Honors College, Honors Research Projects

Industry today thrives off of competition; everybody wants their product to be the best. Across almost every field of manufacturing and design, there is a pattern of factors that companies strive for when producing their specialized products. The most effective companies can create a commodity that is relatively inexpensive, easy to manufacture, and has the ability to meet high standards. As engineers, it is ingrained in us that there is always room for improvement, and that we have been given the tools to make it happen.

When evaluating what needed to be improved in our daily lives, the SAE Zips …

Design And Mechanical Characterization Of 3d Printed Gradient Porosity Poly(Propylene Fumarate) Scaffolds, Andrea Felicelli

Williams Honors College, Honors Research Projects

Worldwide incidence of bone disorders and conditions, an already prevalent problem, is expected to double by 2020 from the rate in 2013 due to factors such as higher life expectancies and lower levels of physical activity. Every year in the United States, over half a million patients receive bone defect repairs, with costs greater than $2.5 billion. Current repairs are typically done with bone grafts, which are often costly and can result in added complications in the donor surgical site. Tissue engineering, a growing field that seeks to assist and enhance tissue defect repairs through the use of synthetic materials, …

Sae Baja Custom Caliper And Upright Design, Katelynn R. Kise

Williams Honors College, Honors Research Projects

The Zips Baja Off-Road Racing team had a successful 2018 season however some aspects of the car needed to be updated and improved for the 2019 season. This reports captures the design cycle performed to improve the cost, integration, and reliability of the front braking caliper and upright.

Metric Coil Car, Abigail Eberly

Williams Honors College, Honors Research Projects

Coil cars are a vital part of many steel mills. They allow mills to easily transfer a coil from one location to another without the use of a crane, manual labor, or other extraneous forces. Steel Equipment Specialists, or SES, gets multiple orders every year for coil cars. While the general functions and goals of the cars remains consistent, the details, such as the size of the car, the distance between rails, and the weight/ size of the coils differs between each place. Due to this variety, SES has requested a coil car that can easily be manipulated and produced …

Carbon Fiber Monocoque, Dan Brown, Leland Hoffman

Williams Honors College, Honors Research Projects

The University of Akron’s Human Powered Vehicle Team designed a high performing, fully functioning vehicle that is safe, efficient, and practical for the 2018-2019 season. These objectives were the main priorities when it came to the initial stages of designing the vehicle. In addition, the vehicle was designed in accordance with the ASME 2019 Human Powered Vehicle Challenge guidelines to satisfy all the rules and requirements. Additional priorities have been created to teach practical engineering skills and techniques to the students participating in the project through different points in the production process including research, vehicle design, construction, and testing.

The …

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Power Wheelchair Canopy, Mohamed F. Battah, Joshua D. Brown, Dujuan J. Mcclendon, Gavin M. Francisco

Williams Honors College, Honors Research Projects

Some power wheelchair users can not drive and independently hold an umbrella at the time because they do not have much upper body strength. Therefore, users are unprotected from the rain and are getting soaking wet. One of the members of this group is in a wheelchair and faces this problem. He has previously searched for something to protect him from rain, but could not found something he could independently use. What users need is a powered umbrella that attaches to their power wheelchair. There is no such umbrella available in the market. In this project, the solution to this …