Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 5 of 5

Full-Text Articles in Engineering

Controlled Release Of Corrosion Inhibitors: Zinc And Magnesium Containing Sodium Chromate, Andrew Thomas Jan 2019

Controlled Release Of Corrosion Inhibitors: Zinc And Magnesium Containing Sodium Chromate, Andrew Thomas

Williams Honors College, Honors Research Projects

Corrosion can be combated by multiple methods, where the primary purpose is to minimize degradation of metal surfaces. Corrosion inhibitors are one of the most effective methods of corrosion protection. Inhibitors are substances that minimize corrosion in aggressive environments, with only a low concentration required. The inhibitors are chemically adsorbed on the surface of the metal and a protective thin film is formed . The mechanism of the inhibitors could be described as anodic, cathodic, or a mix of the two. Anodic inhibitors, also known as passivation inhibitors, alter an anode reaction. Corrosion potential of the metal is shifted to more ...


Cataloging The Degree Of Sensitization Via Electrochemical Reactivation For Studying The Corrosion Behavior Of Inconel 718, Austenitic, And Duplex Stainless Steels, Bradley Lynes Jan 2019

Cataloging The Degree Of Sensitization Via Electrochemical Reactivation For Studying The Corrosion Behavior Of Inconel 718, Austenitic, And Duplex Stainless Steels, Bradley Lynes

Williams Honors College, Honors Research Projects

Corrosion resistant materials can be expensive, but usually reduce the life cycle cost of metallic assets. However, negligent sensitization of these materials can lead to aggressive, intergranular corrosion. Using the methodology of the double loop electrochemical potentiokinetic reactivation (DL-EPR), this project investigates different steel reinforced bars and Inconel to determine the degree of sensitization after a heat treatment of 900°C for 2 hours. The purpose of this research is to validate and determine the appropriate test parameters for performing further DL-EPR test in the future. Additionally, the kinetics observed for each sample during the DL-EPR test will be analyzed ...


Development Of Cardanol-Based Epoxy Coating, Nicholas Pottschmidt Jan 2019

Development Of Cardanol-Based Epoxy Coating, Nicholas Pottschmidt

Williams Honors College, Honors Research Projects

The purpose of this project was to determine the suitability of cardanol glycidyl ether (CGE) as a substitute for trimethylolpropane triglycidyl ether (TMPGE) as the reactive diluent in epoxy coatings. CGE may be a naturally-derived alternative to TMPGE, which is a commonly-used petroleum-derived reactive diluent. Epoxy coatings were formulated with CGE replacing increasing amounts of TMPGE in the formulation. Corrosion protection provided by the coatings was evaluated with electrochemical impedance spectroscopy (EIS). Mechanical properties of the coatings (hardness, flexibility, adhesion, and impact resistance) were evaluated with applicable ASTM standards.

EIS results revealed the coating formulated with only CGE had superior ...


Stress Corrosion Cracking Of Stainless-Steel Reinforced Concrete, Nathan Frye Jan 2019

Stress Corrosion Cracking Of Stainless-Steel Reinforced Concrete, Nathan Frye

Williams Honors College, Honors Research Projects

Stainless steel rebar is one of the most corrosion resistant reinforcing methods for concrete structures. Stainless steel is used for its chromium content and its ability to form a passive oxide corrosion resistant layer. The presence of chloride is one of the largest attackers of this passive film and able to penetrate concrete due to its porous characteristics. This study evaluates the mechanical performance of different stainless steels relative to their changing environments. It is expected that as chloride concentration values increase, mechanical properties will decrease. This will be tested by performing tensile tests on stainless steel rebar sample that ...


Benefits Of Aluminum: Comparing The Common Materials In The Bar Grating Industry, Joanthan Geiser Jan 2019

Benefits Of Aluminum: Comparing The Common Materials In The Bar Grating Industry, Joanthan Geiser

Williams Honors College, Honors Research Projects

The main aim of this project is to study the wholistic behavior of the 6xxx series of aluminum for use in the bar grating industry for a waste water treatment environment. This project will study the comparison of certain aluminum 6xxx series alloys to steel, stainless steel, and glass fiber-reinforced plastic. While comparing these materials, it will look at the mechanical properties such as modulus of elasticity, yield strength, and ultimate tensile strength. In addition, the available corrosion test of the 6xxx series aluminum alloys will be examined to find a generalization of the corrosion behavior for this series. A ...