Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Open Electronics For Medical Devices: State-Of-Art And Unique Advantages, Gaurav Pandey, Ankit Vora
Open Electronics For Medical Devices: State-Of-Art And Unique Advantages, Gaurav Pandey, Ankit Vora
Michigan Tech Publications
A wide range of medical devices have significant electronic components. Compared to open-source medical software, open (and open-source) electronic hardware has been less published in peer-reviewed literature. In this review, we explore the developments, significance, and advantages of using open platform electronic hardware for medical devices. Open hardware electronics platforms offer not just shorter development times, reduced costs, and customization; they also offer a key potential advantage which current commercial medical devices lack—seamless data sharing for machine learning and artificial intelligence. We explore how various electronic platforms such as microcontrollers, single board computers, field programmable gate arrays, development boards, and …
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Michigan Tech Publications
In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404 W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than $2000 USD in materials. The experimentally measured power use …
Antibacterial Properties Of Mussel-Inspired Polydopamine Coatings Prepared By A Simple Two-Step Shaking-Assisted Method, Pegah Kord Fooroshani, Elizabeth Polega, Kevin Thomson, Mohammad Saleh Akram Bhuiyan, Rattapol Pinnaratip, Mikhail Trought, Chito E. Kendrick, Yuesheng Gao, Kahryn Perrine, Lei Pan, Bruce P. Lee
Antibacterial Properties Of Mussel-Inspired Polydopamine Coatings Prepared By A Simple Two-Step Shaking-Assisted Method, Pegah Kord Fooroshani, Elizabeth Polega, Kevin Thomson, Mohammad Saleh Akram Bhuiyan, Rattapol Pinnaratip, Mikhail Trought, Chito E. Kendrick, Yuesheng Gao, Kahryn Perrine, Lei Pan, Bruce P. Lee
Michigan Tech Publications
A simple two-step, shaking-assisted polydopamine (PDA) coating technique was used to impart polypropylene (PP) mesh with antimicrobial properties. In this modified method, a relatively large concentration of dopamine (20 mg ml−1) was first used to create a stable PDA primer layer, while the second step utilized a significantly lower concentration of dopamine (2 mg ml−1) to promote the formation and deposition of large aggregates of PDA nanoparticles. Gentle shaking (70 rpm) was employed to increase the deposition of PDA nanoparticle aggregates and the formation of a thicker PDA coating with nano-scaled surface roughness (RMS = 110 …
Optimal And Decentralized Control Strategies For Inverter-Based Ac Microgrids, Michael D. Cook, Eddy H. Trinklein, Gordon Parker, Rush D. Robinett Iii, Wayne Weaver
Optimal And Decentralized Control Strategies For Inverter-Based Ac Microgrids, Michael D. Cook, Eddy H. Trinklein, Gordon Parker, Rush D. Robinett Iii, Wayne Weaver
Michigan Tech Publications
This paper presents two control strategies: (i) An optimal exergy destruction (OXD) controller and (ii) a decentralized power apportionment (DPA) controller. The OXD controller is an analytical, closed-loop optimal feedforward controller developed utilizing exergy analysis to minimize exergy destruction in an AC inverter microgrid. The OXD controller requires a star or fully connected topology, whereas the DPA operates with no communication among the inverters. The DPA presents a viable alternative to conventional P−ω/Q−V droop control, and does not suffer from fluctuations in bus frequency or steady-state voltage while taking advantage of distributed storage assets necessary for the high penetration of …
Low-Cost Open Source Ultrasound-Sensing Based Navigational Support For The Visually Impaired, Aliaksei Petsiuk, Joshua M. Pearce
Low-Cost Open Source Ultrasound-Sensing Based Navigational Support For The Visually Impaired, Aliaksei Petsiuk, Joshua M. Pearce
Michigan Tech Publications
Nineteen million Americans have significant vision loss. Over 70% of these are not employed full-time, and more than a quarter live below the poverty line. Globally, there are 36 million blind people, but less than half use white canes or more costly commercial sensory substitutions. The quality of life for visually impaired people is hampered by the resultant lack of independence. To help alleviate these challenges this study reports on the development of a low-cost, open-source ultrasound-based navigational support system in the form of a wearable bracelet to allow people with the lost vision to navigate, orient themselves in their …
Neural Network-Based Diagnostic Tool For Detecting Stator Inter-Turn Faults In Line Start Permanent Magnet Synchronous Motors, Luqman S. Maraaba, Zakariya M. Al-Hamouz, Abdulaziz S. Milhem, M. A. Abido
Neural Network-Based Diagnostic Tool For Detecting Stator Inter-Turn Faults In Line Start Permanent Magnet Synchronous Motors, Luqman S. Maraaba, Zakariya M. Al-Hamouz, Abdulaziz S. Milhem, M. A. Abido
Michigan Tech Publications
Three-phase line-start permanent magnet synchronous motors are considered among the most promising types of motors in industrial applications. However, these motors experience several faults, which may cause significant financial losses. This paper proposed a feed-forward neural network-based diagnostic tool for accurate and fast detection of the location and severity of stator inter-turn faults. The input to the neural network is a group of representative statistical and frequency-based features extracted from the steady-state three-phase stator current signals. The current signals with different numbers of shorted turns and loading conditions are captured using the developed finite element JMAG ™ model for interior …
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Michigan Tech Publications
Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm2 was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved …
Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce
Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce
Michigan Tech Publications
Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, the costs of the former and the required electricity to operate the latter limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified, and reliable lab-scale centrifuges. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class (self-replicating rapid prototyper) fused filament fabrication (FFF)- or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open …