Engineering Commons^™

Open Electronics For Medical Devices: State-Of-Art And Unique Advantages, Gaurav Pandey, Ankit Vora

Michigan Tech Publications

A wide range of medical devices have significant electronic components. Compared to open-source medical software, open (and open-source) electronic hardware has been less published in peer-reviewed literature. In this review, we explore the developments, significance, and advantages of using open platform electronic hardware for medical devices. Open hardware electronics platforms offer not just shorter development times, reduced costs, and customization; they also offer a key potential advantage which current commercial medical devices lack—seamless data sharing for machine learning and artificial intelligence. We explore how various electronic platforms such as microcontrollers, single board computers, field programmable gate arrays, development boards, and …

Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce

Michigan Tech Publications

In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404 W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than $2000 USD in materials. The experimentally measured power use …

Antibacterial Properties Of Mussel-Inspired Polydopamine Coatings Prepared By A Simple Two-Step Shaking-Assisted Method, Pegah Kord Fooroshani, Elizabeth Polega, Kevin Thomson, Mohammad Saleh Akram Bhuiyan, Rattapol Pinnaratip, Mikhail Trought, Chito E. Kendrick, Yuesheng Gao, Kahryn Perrine, Lei Pan, Bruce P. Lee

Michigan Tech Publications

A simple two-step, shaking-assisted polydopamine (PDA) coating technique was used to impart polypropylene (PP) mesh with antimicrobial properties. In this modified method, a relatively large concentration of dopamine (20 mg ml⁻¹) was first used to create a stable PDA primer layer, while the second step utilized a significantly lower concentration of dopamine (2 mg ml⁻¹) to promote the formation and deposition of large aggregates of PDA nanoparticles. Gentle shaking (70 rpm) was employed to increase the deposition of PDA nanoparticle aggregates and the formation of a thicker PDA coating with nano-scaled surface roughness (RMS = 110 …

Optimal And Decentralized Control Strategies For Inverter-Based Ac Microgrids, Michael D. Cook, Eddy H. Trinklein, Gordon Parker, Rush D. Robinett Iii, Wayne Weaver

Michigan Tech Publications

This paper presents two control strategies: (i) An optimal exergy destruction (OXD) controller and (ii) a decentralized power apportionment (DPA) controller. The OXD controller is an analytical, closed-loop optimal feedforward controller developed utilizing exergy analysis to minimize exergy destruction in an AC inverter microgrid. The OXD controller requires a star or fully connected topology, whereas the DPA operates with no communication among the inverters. The DPA presents a viable alternative to conventional P−ω/Q−V droop control, and does not suffer from fluctuations in bus frequency or steady-state voltage while taking advantage of distributed storage assets necessary for the high penetration of …

Low-Cost Open Source Ultrasound-Sensing Based Navigational Support For The Visually Impaired, Aliaksei Petsiuk, Joshua M. Pearce

Michigan Tech Publications

Nineteen million Americans have significant vision loss. Over 70% of these are not employed full-time, and more than a quarter live below the poverty line. Globally, there are 36 million blind people, but less than half use white canes or more costly commercial sensory substitutions. The quality of life for visually impaired people is hampered by the resultant lack of independence. To help alleviate these challenges this study reports on the development of a low-cost, open-source ultrasound-based navigational support system in the form of a wearable bracelet to allow people with the lost vision to navigate, orient themselves in their …

Electro-Optic Modulator, Microwave Photonic Link Including An Electro-Optic Modulator, And Method Of Communicating A Signal With An Electro-Optic Modulator, Christopher T. Middlebrook, Arash Hosseinzadeh

Michigan Tech Patents

An electro-optic modulator coupled to an optical source providing an optical power and a radio frequency source providing a radio frequency power. The electro-optic modulator includes a waveguide to receive the optical power, a first ring resonator modulator, and a second ring resonator modulator. The first ring resonator modulator and the second ring resonator modulator receives the radio frequency power, and are coupled to the waveguide for modulating the optical power with the radio frequency power. The first ring resonator modulator and the second ring resonator modulator, with the waveguide, substantially suppress third order intermodulation distortion of a combined power. …

Neural Network-Based Diagnostic Tool For Detecting Stator Inter-Turn Faults In Line Start Permanent Magnet Synchronous Motors, Luqman S. Maraaba, Zakariya M. Al-Hamouz, Abdulaziz S. Milhem, M. A. Abido

Michigan Tech Publications

Three-phase line-start permanent magnet synchronous motors are considered among the most promising types of motors in industrial applications. However, these motors experience several faults, which may cause significant financial losses. This paper proposed a feed-forward neural network-based diagnostic tool for accurate and fast detection of the location and severity of stator inter-turn faults. The input to the neural network is a group of representative statistical and frequency-based features extracted from the steady-state three-phase stator current signals. The current signals with different numbers of shorted turns and loading conditions are captured using the developed finite element JMAG ™ model for interior …

Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications

Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm² was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved …

Open Source Completely 3-D Printable Centrifuge, Salil S. Sule, Aliaksei Petsiuk, Joshua M. Pearce

Michigan Tech Publications

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, the costs of the former and the required electricity to operate the latter limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified, and reliable lab-scale centrifuges. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class (self-replicating rapid prototyper) fused filament fabrication (FFF)- or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open …

Enhancing The Resolution Of Imaging Systems By Spatial Spectrum Manipulation, Wyatt Adams

Dissertations, Master's Theses and Master's Reports

Much research effort has been spent in the 21st century on superresolution imaging techniques, methods which can beat the diffraction limit. Subwavelength composite structures called ``metamaterials" had initially shown great promise in superresolution imaging applications in the early 2000s, owing to their potential for nearly arbitrary capabilities in controlling light. However, for optical frequencies they are often plagued by absorption and scattering losses which can decay or destroy their interesting properties. Similar issues limit the application of other superresolution devices operating as effective media, or metal films that can transfer waves with large momentum by supporting surface plasmon polaritons. In …

Electro-Optic Antenna Elements For Passive Phased Array Radar, Evan Gawron

Dissertations, Master's Theses and Master's Reports

Passive phased antenna arrays are utilized in military and civilian radar systems to determine the received signal origination. Phased array placement for optimal reception is challenging due to the required supporting electronic hardware and the associated coaxial cabling that typically accompanies each antenna channel. Low noise amplifiers and frequency conversion hardware add size and complexity, limiting possible positions for phased array placement. Eliminating required phased array electronic subcomponents without sacrificing function would allow placement onto smaller agile platforms, such as unmanned systems and rapid deployment networks. Electro-optic (EO) antenna elements utilize an optical waveguide embedded between the antenna and ground …

Community Detection In Complex Networks And Application To Dense Wireless Sensor Networks Localization, Sakineh Yazdanparast

Dissertations, Master's Theses and Master's Reports

Complex network analysis is applied in numerous researches. Features and characteristics of complex networks provide information associated with a network feature called community structure. Naturally, nodes with similar attributes will be more likely to form a community. Community detection is described as the process by which complex network data are analyzed to uncover organizational properties, and structure; and ultimately to enable extraction of useful information. Analysis of Wireless Sensor Networks (WSN) is considered as one of the most important categories of network analysis due to their enormous and emerging applications. Most WSN applications are location-aware, which entails precise localization of …

Estimation Of Multi-Directional Ankle Impedance As A Function Of Lower Extremity Muscle Activation, Lauren Knop

Dissertations, Master's Theses and Master's Reports

The purpose of this research is to investigate the relationship between the mechanical impedance of the human ankle and the corresponding lower extremity muscle activity. Three experimental studies were performed to measure the ankle impedance about multiple degrees of freedom (DOF), while the ankle was subjected to different loading conditions and different levels of muscle activity. The first study determined the non-loaded ankle impedance in the sagittal, frontal, and transverse anatomical planes while the ankle was suspended above the ground. The subjects actively co-contracted their agonist and antagonistic muscles to various levels, measured using electromyography (EMG). An Artificial Neural Network …

Online Learning Of The Spatial-Temporal Channel Variation In Underwater Acoustic Communication Networks, Wensheng Sun

Dissertations, Master's Theses and Master's Reports

Influenced by environmental conditions, underwater acoustic (UWA) communication channels exhibit spatial and temporal variations, posing significant challenges for UWA networking and applications. This dissertation develops statistical signal processing approaches to model and predict variations of the channel and relevant environmental factors. Firstly, extensive field experiments are conducted in the Great Lakes region. Three types of the freshwater river/lake acoustic channels are characterized in the aspects of statistical channel variations and sound propagation loss, including stationary, mobile and under-ice acoustic channels. Statistical data analysis shows that relative to oceanic channels, freshwater river/lake channels have larger temporal coherence, higher correlation among densely …

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Estimation And Prediction Of The Human Gait Dynamics For The Control Of An Ankle-Foot Prosthesis, Guilherme Aramizo Ribeiro

Dissertations, Master's Theses and Master's Reports

With the growing population of amputees, powered prostheses can be a solution to improve the quality of life for many people. Powered ankle-foot prostheses can be made to behave similar to the lost limb via controllers that emulate the mechanical impedance of the human ankle. Therefore, the understanding of human ankle dynamics is of major significance. First, this work reports the modulation of the mechanical impedance via two mechanisms: the co-contraction of the calf muscles and a change of mean ankle torque and angle. Then, the mechanical impedance of the ankle was determined, for the first time, as a multivariable …

Modeling And Control Of Maximum Pressure Rise Rate In Rcci Engines, Aditya Basina

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) is a combustion strategy that burns fuel at lower temperatures and leaner mixtures in order to achieve high efficiency and near zero NOx emissions. Since the combustion happens at lower temperatures it inhibits the formation of NOx and soot emissions. One such strategy is Reactivity Controlled Compression Ignition (RCCI). One characteristic of RCCI combustion and LTC com- bustion in general is short burn durations which leads to high Pressure Rise Rates (PRR). This limits the operation of these engines to lower loads as at high loads, the Maximum Pressure Rise Rate (MPRR) hinders the use of …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Lithium-Ion Battery Degradation Evaluation Through Bayesian Network Method For Residential Energy Storage Systems, Khalid Khan

Dissertations, Master's Theses and Master's Reports

Batteries continue to infiltrate in innovative applications with the technological advancements led by Li-ion chemistry in the past decade. Residential energy storage is one such example, made possible by increasing efficiency and decreasing the cost of solar PV. Residential energy storage, charged by rooftop solar PV is tied to the grid, provides household loads. This multi-operation role has a significant effect on battery degradation. These contributing factors especially solar irradiation and weather conditions are highly variable and can only be explained with probabilistic analysis. However, the effect of such external factors on battery degradation is approached in recent literature with …

Effect Of Sensor Errors On Autonomous Steering Control And Application Of Sensor Fusion For Robust Navigation, Shuvodeep Bhattacharjya

Dissertations, Master's Theses and Master's Reports

Autonomous steering control is one the most important features in autonomous vehicle navigation. The nature and tuning of the controller decides how well the vehicle follows a defined trajectory. A poorly tuned controller can cause the vehicle to oversteer or understeer at turns leading to deviation from a defined path. However, controller performance also depends on the state–feedback system. If the states used for controller input are noisy or has bias / systematic error, the navigation performance of the vehicle is affected irrespective of the control law and controller tuning. In this report, autonomous steering controller analysis is done for …

Development Of The Coil Volume Method For Time-Domain Simulation Of Internal Faults In Transformers, Elizaveta Egorova

Dissertations, Master's Theses and Master's Reports

A power transformer is a very important and expensive asset for a utility. As for any other power equipment, the transformer is subject to internal faults. The extent of transformer damage depends on the fault duration. Therefore, the protective relays should provide for sensitivity, selectivity, and speed of operation to minimize the effects of damaging conditions. High sensitivity of the relay allows it to identify internal faults quickly. However, the relay should not jeopardize the normal operation of the transformer. To determine desirable relay settings, a transformer model for simulation of internal faults is required.

Transformer models, shown in the …