Engineering Commons^™

Medical Dental Device: Biogeneric Implant Prototype, Ibeth Erazo, Aneeza Hussain, Renata Budny, Gaffar Gailani

Publications and Research

Teeth are lost due to tooth decay, injury, disease, or other causes. Today, dental implants extend the range of care to a variety of patients undergoing necessary prosthodontic rehabilitation. If the benefits of such treatments are to be maximized, then implants must be selected on logical basis and placed within the context of the full range of treatment modalities. However, modern dental implant systems are based on multiple components often leading to micro-movements which cause stress on the bone or bacterial infections, both of which compromise the success of osseointegration and consequently jeopardize the whole implant adaptation. Thus, a new …

Stretchable Piezoelectric Power Generators Based On Zno Thin Films On Elastic Substrates, Ioana Voiculescu, Fang Li, Glen Kowach, Nicolas Mistou, Russell Kastberg

Publications and Research

The paper describes a stretchable, microfabricated power generator that will be attached on the skin and will produce energy based on the movements of the human body. The device was fabricated on a polymeric, elastomeric, poly(dimethylsiloxane) (PDMS) sheet. It consists of a piezoelectric thin film of ZnO sandwiched between two stretchable gold electrodes. An innovative technique was used for the deposition of ZnO thin film on the gold electrode-coated polymeric substrate at low temperatures below 150C. This is the first attempt to use a uniform film of ZnO, for energy harvesting. The ZnO film had the thickness at the submicron …

Quantification Of Heat Flows Through Building Entrance Doors On A Winter Day, Daeho Kang

Publications and Research

The current methods for the prediction of the heat flow through building entrance doors have been used for years while involved with a certain degree of uncertainty. This paper describes an experimental method that accurately quantified such heat flow. The experiment monitored local environmental parameters in a college building on a cold winter day. The results of the experiment demonstrated that the experimental method is viable to accurately estimate the heat flow throughout the entrance doors and the presence of a vestibule moderated heat losses from the conditioned area. The results will be used for validating the existing methods.

Competence Of A Spray Passive Down-Draft Evaporative Cooling (Pdec) System For Space Cooling, Daeho Kang, Richard K. Strand

Publications and Research

A spray PDEC system has been relatively less considered than other passive cooling strategies as one of the viable low-energy solutions in the cooling of buildings while having a great potential in energy savings. This study is intended to evaluate the capability of a spray PDEC system for space cooling. It comprises four simulation scenarios to see the system response and influence of indoor thermal environment when a spray PDEC system is adopted as a primary cooling system in two different climates. The simulation results show that a spray PDEC system causes a substantial variation in the indoor thermal environment …

Analysis Of The System Response Of A Spray Passive Downdraft Evaporative Cooling System, Daeho Kang, Richard K. Strand

Publications and Research

A spray Passive Downdraft Evaporative Cooling (PDEC) system achieves great savings for space cooling and improves indoor environmental quality by supplying a large amount of fresh outdoor air. As previous studies heavily focused on the energy saving capability of a spray PDEC system due to lack of methods for a detailed analysis, the influence of cool humid supply air from a spray PDEC system in a space in buildings has not been comprehensively studied. This study is intended to evaluate the competence of a spray PDEC system as a primary cooling system in typical spaces in a primary school building …

Restore-L Satellite Servicing Internship Final Report, Giovanni Campos

Publications and Research

This paper reviews the Restore-L mission purpose and the necessary research and simulations to meet mission specification for the Propellant Transfer Subsystem (PTS). It is essential the PTS undergoes functionality testing, environmental testing, and calculations to understand the capabilities of the system. For the testing of components from PTS, a proper test setup is required. It is vital for test hardware, such as hoses and valves, to stay in place while the test is being performed. For the test hardware to operate correctly, positioning, orientation, and alignment are critical as well. In addition to the testing, calculations for pressure drop …

Wrinkling Of Membrane And Thin Film Under Torsion, Tingting Chen

Dissertations and Theses

Membranes and thin film structures are widely used in modern technologies. Applications include solar sails and sunshields in space missions, biological membranes and flexible circuit boards. Wrinkling of membrane or a stiff film on a soft substrate may occur in either desired or unwanted patterns. This work tries to obtain some understanding on the wrinkling phenomenon and provide guidance in avoiding wrinkling or effectively controlling the wrinkle patterns.

Many works have been published about wrinkling in the thin sheets since the 20^th century. However, there is no simple analytical way to systematically characterize the wrinkling in these studies. In …

The Influence Of Size And Progression Of Intra-Cerebral Hematoma On The Lateral Ventricles, Muhammad J. Ashraf

Dissertations and Theses

Cerebrovascular diseases like intra cerebral hemorrhage are quite deadly and may disturb functioning of the brain, expanding and resulting in formation of an intra cerebral hematoma(ICH). It is imperative to comprehend how hematoma and its expansion inside the brain endangers human life. One of the influences of an ICH inside brain tissue is on the Lateral Ventricles(LV). When the hemorrhage occurs close enough to the lateral ventricles, filled with cerebrospinal fluid(CSF), it disrupts the balance of fluid in LV. A minor pressure change in LV can negatively influence the production of CSF as well as an increase in intracranial pressure. …

Void Fraction Measurements In Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensor And Pressure Transducers- Effect Of Sparger, Afolabi Gabriel Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

System Dynamics And Control, Benjamin Liaw

Open Educational Resources

Model development with applications to mechanical engineering systems. First and higher order system responses. Laplace transform, transfer functions and block diagrams. Frequency response and vibration. Introduction to feedback control. Concepts of PID control, tuning and compensation. Routh-Hurwitz stability. Control analysis and design using various graphical methods such as root locus, Bode diagram, Nyquist plot and Nichols chart. Hands-on experiments include dynamics and controls of mechanical, servo motor, fluid level/flow, pneumatic and temperature processing systems and vibration of various degree-of-freedom systems.

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Void Fraction Measurements In A Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensors And Pressure Transducers: Effect Of Spargers, Afolabi G. Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Development Of Electromagnetic Friction Dampers For Improving Seismic Performance Of Civil Structures, Mohsen Amjadian

Dissertations and Theses

Energy dissipation is critical to limiting damage to civil structures subjected to extreme natural events such as earthquakes. Friction is one of the most reliable mechanisms of energy dissipation that has been utilized extensively in friction dampers to improve seismic performance of civil structures. Friction dampers are well-known for having a highly nonlinear hysteretic behavior caused by stick-slip motion at low velocities, a phenomenon that is inherent in friction and increases the acceleration response of the structure under control unfavorably, in spite of the fact that the displacement is generally reduced because of the energy dissipation. This increase in acceleration …