Engineering Commons^™

Preparation Of Glass-Ceramics Largely Using Steelmaking Slags And Study On The Effect Of Iron Content On Properties Of Glass-Ceramics, Huan Feng

Huan Feng

Glass-ceramics were prepared using steelmaking industry waste containing high iron content based on powder sintering and crystallization method. Anthracite was used in varying amounts as the reducing agent to recover iron in raw materials. X-ray diffraction analysis (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscope (SEM) coupled with Energy Dispersive X-ray spectrometer (EDX) were used to study the microstructure of glass-ceramics formed. Bending strength and micro-harness of the samples were compared. When 12g of anthracite was used, ionic iron (Fe 2+ /Fe 3+ ) content was reduced to 4.7% and total iron content was reduced to 8.0% in …

Mechatronics Education At Kettering University: Development Of Learning- Specific Hardware And Software, Jeffrey Hargrove, Theodore J. Stokes

Jeffrey Hargrove

A series of learning-specific electronic circuit boards and associated software has been developed to support mechatronics education in the Mechanical Engineering Department at Kettering University. The boards are designed to interface to the Toshiba TLCS-900H Microprocessor Trainer and Evaluation Board. The purpose of these boards is to provide mechanical engineering students of mechatronics with robust hardware that readily permits interfacing of sensors and actuators to microcontrollers used in mechatronic applications. Further, the boards feature signal conditioning circuits for use in conjunction with sensors, and driver circuits for operating high-current actuating devices. Supporting software has been written to permit ready use …

Development And Implementation Of Mechatronics Education At Kettering University, Jeffrey Hargrove

Jeffrey Hargrove

The Mechanical Engineering Department at Kettering University has completed development of a significant new component of education in mechatronics. The work began in the fall of 1997 as the principal part of an award for “Instrumentation and Laboratory Improvement” by the Division of Undergraduate Education of the National Science Foundation. It has culminated with the successful implementation of two undergraduate courses in mechatronics, two mechatronics laboratories and a website to support the educational endeavors of the mechatronics students. As will be described in this paper, the first course and its laboratory exercises are designed specifically to provide the students with …

Potential Economic Impacts Of Allocating More Land For Bioenergy Biomass Production In Virginia, Thomas O. Ochuodho, Janaki R. R. Alavalapati, Pankaj Lal, Domena A. Agyeman, Bernabas Wolde, Pralhad Burli

Pankaj Lal

The growing attention to renewable energy and rural development has created greater demand for production of biomass feedstock for bioenergy. However, forest growth rates and the amount of land in most existing forests may not be sufficient to sustainably supply the forest biomass required to support existing forest products industries and the expanding bioenergy industry. Additionally, concerns about agricultural land use competition have dampened expansion of biomass production on agricultural land base. One of the ways to meet the growing forest biomass feedstock demand for bioenergy production is by allocating currently marginal non-forested land for growing bioenergy feedstocks. In Virginia, …

Transparent Solar Windows From Labs To Industry, Towards Smart Cities - Encyclopedia- Oct 2019.Pdf, Mohammad Nur-E-Alam, Mikhail Vasiliev, Kamal Alameh

Mikhail Vasiliev

Performance, Workload, And Usability In A Multiscreen, Multi-Device, Information-Rich Environment, Jason J. Saleem, Dustin T. Weiler

Jason Saleem

Potential benefits of multiscreen and multiple device environments were assessed using three different computing environments. A single factor, within-subject study was conducted with 18 engineering students in a laboratory experiment. Three levels for the computing environment factor included one with a desktop computer with a single monitor (control, condition A); one with a desktop with dual monitors, as well as a single tablet computer (condition B); and one with a desktop with a single monitor, as well as two tablet computers (condition C). There was no statistically significant difference in efficiency or workload when completing scenarios for the three computing …

Ambulatory Clinic Exam Room Design With Respect To Computing Devices: A Laboratory Simulation Study, Dustin T. Weiler, Tyler Satterly, Shakaib U. Rehman, Maury A. Nussbaum, Neale R. Chumbler, Gary M. Fischer, Jason J. Saleem

Jason Saleem

Background—Challenges persist regarding how to integrate computing effectively into the exam room, while maintaining patient-centered care. Purpose—Our objective was to evaluate a new exam room design with respect to the computing layout, which included a wall-mounted monitor for ease of (re)-positioning. Methods—In a lab-based experiment, 28 providers used prototypes of the new and older “legacy” outpatient exam room layouts in a within-subject comparison using simulated patient encounters. We measured efficiency, errors, workload, patient-centeredness (proportion of time the provider was focused on the patient), amount of screen sharing with the patient, workflow integration, and provider situation awareness. Results—There were no statistically …

Smart Shrinkage: Better Planning And Decision-Making For Legacy Cities, Michael P. Johnson Jr.

Michael P. Johnson

Informs Seattle Dei Final 191020.Pdf, Michael P. Johnson Jr.

Michael P. Johnson

Learning Streams: A Case Study In Curriculum Integration, Mani Mina, Arun K. Somani, Akhilesh Tyagi, Diane T. Rover, Matthew Feldmann, Mack C. Shelley

Diane Rover

During 2004-2005, the Departments of Electrical and Computer Engineering and Mechanical Engineering at Iowa State University in collaboration with educational colleagues in the Research Institute for Studies in Education piloted a new curricula model to improve student learning through vertical integration of educational activities using new program structures. We offered an experimental course sequence during Fall 2004 and Spring 2005, defined as a “learning stream.” A learning stream is a basic element of a novel program structure designed specifically to vertically integrate subject matter across courses. A learning stream merges and re-organizes material to more effectively present and reinforce key …

Work In Progress - Preparation Creating Effective Faculty Of Engineering: A Technological Literacy Approach, Mani Mina, Diane T. Rover, Mack C. Shelley

Diane Rover

This paper reviews the framework and provides new result for the implementation of a new program designed to develop more effective future faculty in engineering. The core of the proposed program will be based on our efforts regarding the recently developed Minor in Engineering Studies (MES). This program will team up effective engineering faculty to train, mentor, and evaluate a select group of graduate students to teach classes in our MES program. The goal is to help the engineering graduate students (the graduate educators) become better communicator and better educators by training non-engineering students in technological literacy classes. This practice …

Connected Home Security Systems Market Is Expected To Reach Us$ 32.5 Bn By 2026.Pdf, Johnson Paul

Johnson Paul

Uncertainty Theory Based Reliability-Centric Cyber-Physical System Design, Houbing Song, Ya Jiang, Mingzhe Wang, Xun Jiao, Hui Kong, Rui Wang, Yongxin Liu, Jian Wang, Jiaguang Sun

Houbing Song

Cyber-physical systems (CPSs) are built from, and depend upon, the seamless integration of software and hardware components. The most important challenge in CPS design and verification is to design CPS to be reliable in a variety of uncertainties, i.e., unanticipated and rapidly evolving environments and disturbances. The costs, delays and reliability of the designed CPS are highly dependent on software-hardware partitioning in the design. The key challenges in partitioning CPSs is that it is difficult to formalize reliability characterization in the same way as the uncertain cost and time delay.

In this paper, we propose a new CPS design paradigm …

Data‐Enabled Cognitive Modeling: Validating Student Engineers’ Fuzzy Design‐Based Decision‐Making In A Virtual Design Problem, Golnaz Arastoopour Irgens, Naomi C. Chesler, Jeffrey Linderoth, David Williamson Shaffer

Golnaz Arastoopour Irgens

The ability of future engineering professionals to solve complex real‐world problems depends on their design education and training. Because engineers engage with open‐ended problems in which there are unknown parameters and multiple competing objectives, they engage in fuzzy decision‐making, a method of making decisions that takes into account inherent imprecisions and uncertainties in the real world. In the design‐based decision‐making field, few studies have applied fuzzy decision‐making models to actual decision‐making process data. Thus, in this study, we use datasets on student decision‐making processes to validate approximate fuzzy models of student decision‐making, which we call data‐enabled cognitive modeling. The results …

Forensicloud: An Architecture For Digital Forensic Analysis In The Cloud, Cody Miller, Dae Glendowne, David Dampier, Kendall Blaylock

David Dampier

The amount of data that must be processed in current digital forensic examinations continues to rise. Both the volume and diversity of data are obstacles to the timely completion of forensic investigations. Additionally, some law enforcement agencies do not have the resources to handle cases of even moderate size. To address these issues we have developed an architecture for a cloud-based distributed processing platform we have named Forensicloud. This architecture is designed to reduce the time taken to process digital evidence by leveraging the power of a high performance computing platform and by adapting existing tools to operate within this …

Competing Magnetic Phases And Itinerant Magnetic Frustration In Srco2 As2, Bing Li, Benjamin G. Ueland, W. T. Jayasekara, D. L. Abernathy, N. S. Sangeetha, David C. Johnston, Qing-Ping Ding, Yuji Furukawa, Peter P. Orth, Andreas Kreyssig, Alan I. Goldman, Robert J. Mcqueeney

A. I. Goldman

Whereas magnetic frustration is typically associated with local-moment magnets in special geometric arrangements, here we show that SrCo2As2 is a candidate for frustrated itinerant magnetism. Using inelastic neutron scattering (INS), we find that antiferromagnetic (AF) spin fluctuations develop in the square Co layers of SrCo2As2 below T approximate to 100 K centered at the stripe-type AF propagation vector of (1/2, 1/2), and that their development is concomitant with a suppression of the uniform magnetic susceptibility determined via magnetization measurements. We interpret this switch in spectral weight as signaling a temperature-induced crossover from an instability toward ferromagnetism ordering to an instability …

Guest Editorial Special Issue On Toward Securing Internet Of Connected Vehicles (Iov) From Virtual Vehicle Hijacking, Yue Cao, Houbing Song, Omprakash Kaiwartya, Sinem Coleri Ergen, Jaime Lloret, Naveed Ahmad

Houbing Song

Today’s vehicles are no longer stand-alone transportation means, due to the advancements on vehicle-tovehicle (V2V) and vehicle-to-infrastructure (V2I) communications enabled to access the Internet via recent technologies in mobile communications, including WiFi, Bluetooth, 4G, and even 5G networks. The Internet of vehicles was aimed toward sustainable developments in transportation by enhancing safety and efficiency. The sensor-enabled intelligent automation of vehicles’ mechanical operations enhances safety in on-road traveling, and cooperative traffic information sharing in vehicular networks improves traveling efficiency.

Design Of Personnel Big Data Management System Based On Blockchain, Houbing Song, Jian Chen, Zhihan Lv

Houbing Song

With the continuous development of information technology, enterprises, universities and governments are constantly stepping up the construction of electronic personnel information management system. The information of hundreds of thousands or even millions of people’s information are collected and stored into the system. So much information provides the cornerstone for the development of big data, if such data is tampered with or leaked, it will cause irreparable serious damage. However, in recent years, electronic archives have exposed a series of problems such as information leakage, information tampering, and information loss, which has made the reform of personnel information management more and …

Adaboost‑Based Security Level Classifcation Of Mobile Intelligent Terminals, Feng Wang, Houbing Song, Dingde Jiang, Hong Wen

Houbing Song

With the rapid development of Internet of Things, massive mobile intelligent terminals are ready to access edge servers for real-time data calculation and interaction. However, the risk of private data leakage follows simultaneously. As the administrator of all intelligent terminals in a region, the edge server needs to clarify the ability of the managed intelligent terminals to defend against malicious attacks. Therefore, the security level classification for mobile intelligent terminals before accessing the network is indispensable. In this paper, we firstly propose a safety assessment method to detect the weakness of mobile intelligent terminals. Secondly, we match the evaluation results …

Initial Field Testing Results From Building-Integrated Solar Energy Harvesting Windows Installation In Perth, Australia, Mikhail Vasiliev, Mohammad Nur-E-Alam, Kamal Alameh

Mikhail Vasiliev

An Under-Hand Steering Wheel Grasp Produces Significant Risk To The Upper Extremity During Airbag Deployment, Patrick J. Atkinson, Prem Hariharan, Shresta Mari-Gowda, Paul Telehowski, Sidney Martin, Jack Van Hoof, Cynthia Bir, Theresa Atkinson

Theresa Atkinson

Recent laboratory investigations suggest that a deploying airbag may fracture the forearm. These studies positioned the arm in an overhand grasp placing the forearm over the airbag module. However, there is little published data on how drivers grip the steering wheel and the general proximity of the upper extremity to the airbag module. The objective of the current study was to identify 'real world' upper extremity positions and to correlate these with accident and experimental data. A survey of the National Automotive Sampling System (NASS) for the years 1995-99 revealed an increase in the number of forearm fractures due to …

Crash Safety In The Introductory Physics Lab, Daniel Ludwigsen, Janet Brelin-Fornari, Joseph Neal

Daniel Ludwigsen

Crash Safety in the Introductory Physics Lab Abstract In the field of vehicle occupant protection and crash safety, the Deceleration Sled offers researchers a controlled, repeatable, and relatively cost-effective means to test interior parts such as safety restraint systems. The sled can accelerate a 2000 lb payload to achieve a speed of 40 mph before a hydraulically controlled deceleration models the deformation of the vehicle structure during a crash. Understanding the dynamics of the sled and interpreting test results incorporates many of the core concepts of a first course in introductory physics. This application of physics principles is the inspiration …

Crash Safety In The Introductory Physics Lab, Daniel Ludwigsen, Janet Brelin-Fornari, Joseph Neal

Daniel Ludwigsen

Crash Safety in the Introductory Physics Lab Abstract In the field of vehicle occupant protection and crash safety, the Deceleration Sled offers researchers a controlled, repeatable, and relatively cost-effective means to test interior parts such as safety restraint systems. The sled can accelerate a 2000 lb payload to achieve a speed of 40 mph before a hydraulically controlled deceleration models the deformation of the vehicle structure during a crash. Understanding the dynamics of the sled and interpreting test results incorporates many of the core concepts of a first course in introductory physics. This application of physics principles is the inspiration …

Evaluating Impact Attenuator Performance For A Formula Sae Vehicle, Jason Fahland, Craig Hoff, Janet Brelin-Fornari

Craig Hoff

Formula SAE® is one of several student design competitions organized by SAE International. In the Formula SAE events undergraduate and graduate students are required to conceive, design, fabricate and compete with a small, formula-style, race car. Formula SAE safety rules dictate a 7 m/s (or approximately 15.65 mph) frontal crash test for nose mounted impact attenuators. These rules are outlined in section B3.21 of the Formula SAE rule book. Development and testing methods of these energy absorbing devices have varied widely among teams. This paper uses real world crash sled results to research methods for predicting the performance of aluminum …

Immobilization Of The Influenza A M2 Transmembrane Peptide In Virus Envelope−Mimetic Lipid Membranes: A Solid-State Nmr Investigation, Wenbin Luo, Sarah D. Cady, Mei Hong

Sarah Cady

The dynamic and structural properties of membrane proteins are intimately affected by the lipid bilayer. One property of membrane proteins is uniaxial rotational diffusion, which depends on the membrane viscosity and thickness. This rotational diffusion is readily manifested in solid-state NMR spectra as characteristic line shapes and temperature-dependent line narrowing or broadening. We show here that this whole-body uniaxial diffusion is suppressed in lipid bilayers mimicking the composition of eukaryotic cell membranes, which are rich in cholesterol and sphingomyelin. We demonstrate this membrane-induced immobilization on the transmembrane peptide of the influenza A M2 (AM2-TM) proton channel protein. At physiological temperature, …

Multiple Path Particle Dosimetry For Prediction Of Mouse Lung Deposition Of Nanoaerosol Particles, Mohammed Ali

Mohammed Ali

Nanoaerosolized particle (dia.<200 >nm) antibiotic inhalation therapy was tested to treat pneumonic tularemia in mice caused by Francisella novicida infection. Very limited experimental techniques are available to properly estimate inhaled doses and distribution of the drug inside the mouse lungs. To overcome this problem, computational simulation of particle deposition based on the Multiple Path Particle Dosimetry (MPPD) model was employed to simulate in vivo experimental conditions which included nasal breathing with whole body exposure to the antibiotic in the form of nano-aerosolized medicine. The deposition results were compared with several in vivo experimental data reported in literature; and satisfactory agreements …

Effects Of Three Dry Powder Inhalers On Deposition Of Aerosolized Medicine In The Human Oral-Pharyngeal-Laryngeal Regions, Mohammed Ali

Mohammed Ali

The dry powder inhaler (DPI) is a popular, effective and convenient drug delivery device for inhalation therapy to treat asthma. However, a large quantity (approximately 54%) of inhaled aerosols deposit in the oropharyngeal region. Deposition in this region is undesirable because it provides minimum therapeutic benefits and has adverse localized or systemic side effects. This study reports a method of examining electrostatic charge effects on deposition of three DPI aerosols (Spiriva^™ Handihaler, Advair Diskus^™, and Pulmicort^™ Turbohaler) in a cadaver-based cast of the human oral-pharyngeal-laryngeal (OPL) regions. Experimental aerosols were generated from the three commercially available …

Drainage Water Quality Impacts Of Agricultural Management Practices: Effectof Manure Application Timing And Cover Crops, Brian Dougherty, Carl Pederson, Matt Helmers, Michelle Soupir, Dan Andersen, Antonio Mallarino, John Sawyer

John E. Sawyer

A primary objective of this study is to evaluate the impact of various cropping and nutrient management systems on crop yields and drainage water quality. This progress report only includes the first-year corn grain yield results. Treatment comparisons include the impact of early fall vs. late fall vs. spring application of liquid swine manure, nitrification inhibitor with late fall swine manure application, cereal rye cover crop, and gypsum application. These comparisons will be conducted for multiple years and used to develop appropriate manure and nutrient management practices to minimize water contamination potential and enhance the use of swine manure as …

Research Toward A Partially-Automated, And Crime Specific Digital Triage Process Model, Gary Cantrell, David Dampier, Yoginder S. Dandass, Nan Niu, Chris Bogen

David Dampier

The digital forensic process as traditionally laid out begins with the collection, duplication, and authentication of every piece of digital media prior to examination. These first three phases of the digital forensic process are by far the most costly. However, complete forensic duplication is standard practice among digital forensic laboratories.

The time it takes to complete these stages is quickly becoming a serious problem. Digital forensic laboratories do not have the resources and time to keep up with the growing demand for digital forensic examinations with the current methodologies. One solution to this problem is the use of pre-examination techniques …

Salinity Gradient Power (Sgp): A Developmental Roadmap Covering Existing Generation Technologies And Recent Investigative Results Into The Feasibility Of Bipolar Membrane-Based Salinity Gradient Power Generation, Clifford R. Merz, Wilfrido A. Moreno, Marilyn Barger, Stephen M. Lipka

Clifford Merz

Besides wind and solar-based renewable energy technologies, marine sources are being actively discussed. Sources of marine renewable energy traditionally have included ocean currents, ocean waves, tides, thermal gradients, and salinity gradients. Salinity gradient power (SGP) is an attractive marine renewable resource because it possesses not only the largest energy potential but likely the largest total available resource as well. SGP is instantly available when diluted and concentrated ionic solutions are mixed; is renewable, sustainable, and produces no CO₂ emissions or other significant effluents that may interfere with global climate. The ultimate challenge is in the economics of the recovery …