Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 4 of 4

Full-Text Articles in Engineering

Quantifying Restoration Costs In The Aftermath Of An Extreme Event Using System Dynamics And Dynamic Mathematical Modeling Approaches, Akhilesh Ojha Jan 2019

Quantifying Restoration Costs In The Aftermath Of An Extreme Event Using System Dynamics And Dynamic Mathematical Modeling Approaches, Akhilesh Ojha

Doctoral Dissertations

"Extreme events such as earthquakes, hurricanes, and the like, lead to devastating effects that may render multiple supply chain critical infrastructure elements inoperable. The economic losses caused by extreme events continue well after the emergency response phase has ended and are a key factor in determining the best path for post-disaster restoration. It is essential to develop efficient restoration and disaster management strategies to ameliorate the losses from such events. This dissertation extends the existing knowledge base on disaster management and restoration through the creation of models and tools that identify the relationship between production losses and restoration costs. The ...


The Tabu Ant Colony Optimizer And Its Application In An Energy Market, David Donald Haynes Jan 2019

The Tabu Ant Colony Optimizer And Its Application In An Energy Market, David Donald Haynes

Doctoral Dissertations

"A new ant colony optimizer, the 'tabu ant colony optimizer' (TabuACO) is introduced, tested, and applied to a contemporary problem. The TabuACO uses both attractive and repulsive pheromones to speed convergence to a solution. The dual pheromone TabuACO is benchmarked against several other solvers using the traveling salesman problem (TSP), the quadratic assignment problem (QAP), and the Steiner tree problem. In tree-shaped puzzles, the dual pheromone TabuACO was able to demonstrate a significant improvement in performance over a conventional ACO. As the amount of connectedness in the network increased, the dual pheromone TabuACO offered less improvement in performance over the ...


Power System Planning In Disparate Systems: Modeling Sustainability And Electricity Access, Destenie Nock Jan 2019

Power System Planning In Disparate Systems: Modeling Sustainability And Electricity Access, Destenie Nock

Doctoral Dissertations

Electricity goals around the world tend to focus on increasing social benefit through one of two avenues: (1) increasing overall system sustainability or (2) increasing access to electricity. These goals guide the transition of the power system. In pursuit of these goals decision makers will need modeling tools that can inform decisions, in a way that is flexible enough to include a wide range of preferences and goals. It is clear that the future generation mix of the power system will change, but the most sustainable solution, will change based on a country's goals. This dissertation will explore the ...


Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li Jan 2019

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.