Engineering Commons^™

Comparison Study Between Post-Fermentation Stillage And Pre-Fermentation Mash Utilizing Acidification And Steam Explosion Techniques For Cellulose Saccharification, Daniel Mckee

Master's Theses

Pre-fermentation mash fiber and post-distillation stillage fiber were examined and compared using a variety of preparatory techniques to determine the better source for cellulose fiber saccharification. Once screened, dried, and diluted to a 10% solution, mash fiber and stillage fiber were exposed to increasing temperatures for steam explosion techniques as well as increasing acidification techniques. Both underwent enzymatic saccharification to convert the exposed cellulose to glucose and other sugars. Once the optimum steam explosion technique parameters and acidification parameters were determined to be 2.5% sulfuric acid at 127.8°C for 1 hour, a comparison of the saccharification of pre-fermentation mash fiber …

Sex Differences In Collateral Remodeling Following Hindlimb Arterial Occlusion, Laura Burckhardt

Master's Theses

Clinical evidence indicates a higher incidence of peripheral arterial occlusive disease and associated likelihood of critical limb ischemia in women, as well as worse prognosis and decreased survival post myocardial infarction. Therefore, understanding the possible differences in underlying vascular compensation mechanisms is crucial. With arterial occlusions, necrosis and tissue injury can be naturally mitigated by the collateral circulation, improving patient prognosis. Previous sex-comparison studies describing differences in vascular remodeling are inconsistent. Therefore, the aim of this study was to describe the effect of arterial occlusion on collateral remodeling in healthy male and healthy reproductive-stage female mice. At 7 days following …

Interfacing A Hirudo Medicinalis Retzius Cell With Insulated Gate Of Mosfet, Rachel M. Smith

Master's Theses

Much work has been done to study the external stimulation of nervous tissue as well as the transmission of neural signals to electronics. Peter Fromherz was one of the pioneers in this area of electrophysiology, with a series of experiments in the 1990s that aimed to characterize and optimize the interface between neural tissue and transistors. In this thesis, Kurt Sjoberg and I interfaced a Retzius cell isolated from a Hirudo medicinalis ganglion with the insulated gate of a MOSFET. The goal was to see change in membrane potential that could be related Fromherz’s original 1991 work. Our experimental setup …

Thermal-Fluid Dynamic Model Of Luge Steels, Brandon Stell

Master's Theses

Luge is an Olympic sport in which athletes ride feet-first on sleds down an ice-covered track. Competitors spring from the starting position and accelerate their sled by paddling with spiked gloves against the ice surface. Once the Luger leaves the starting section, their downhill motion is solely propelled by the effects of gravity. Athletes compete, one after the other, for the fastest time. Runs can differ by as little as a thousandth of a second, meaning that every minor sled adjustment, change of line choice, and shift of body position is critical. In the past, the sport of Luge has …

Sd-Mcan: A Software-Defined Solution For Ip Mobility In Campus Area Networks, Adam Chase Calabrigo

Master's Theses

Campus Area Networks (CANs) are a subset of enterprise networks, comprised of a network core connecting multiple Local Area Networks (LANs) across a college campus. Traditionally, hosts connect to the CAN via a single point of attachment; however, the past decade has seen the employment of mobile computing rise dramatically. Mobile devices must obtain new Internet Protocol (IP) addresses at each LAN as they migrate, wasting address space and disrupting host services. To prevent these issues, modern CANs should support IP mobility: allowing devices to keep a single IP address as they migrate between LANs with low-latency handoffs. Traditional approaches …

Smart Dc/Dc Wall Plug Design For The Dc House Project, Richard Sinclair Liu

Master's Theses

The present day duplex wall receptacle in the United States provides 120Vrms AC at 60Hz, which comes from a standard set for AC loads by the National Electrical Manufacturers Association. With a DC system, such as what is used in the DC House project currently being developed at Cal Poly, providing DC power to DC loads presents a technical challenge due to the different required DC operating voltages of the loads. This thesis entails the design and construction of a Smart DC/DC Wall Plug, which can automatically adjust its output voltage to match any required DC load voltages. In the …

The Role Of Soil Stiffness In Reverse Fault Rupture Propagation, Moises I. Buelna

Master's Theses

A nonlinear Mohr-Coulomb constitutive model with a strain dependent yield surface and non-associated flow was employed to study the plastic soil properties which affect the rate of surface fault rupture propagation in reverse events. These numerical simulations show a trend for soils with higher stiffness to have a higher rate of rupture propagation. Additionally the study shows the effects of strain softening and hardening on the rate of rupture propagation. Soils which strain harden exhibiting ductile behavior typically require more basal offset to rupture to the surface than soils which strain soften exhibiting brittle behavior. These results agree with our …

Eeg Characterization During Motor Tasks That Are Difficult For Movement Disorder Patients, Adam Joshua Aslam

Master's Theses

Movement disorders are a group of syndromes that often arise due to neurological abnormalities. Approximately 40 million Americans are affected by some form of movement disorder, significantly impacting patients’ quality of life and their ability to live independently. Deep brain stimulation (DBS) is one treatment that has shown promising results in the past couple decades, however, the currently used open-loop system has several drawbacks. By implementing a closed-loop or adaptive DBS (aDBS) system, the need for expensive parameter reprogramming sessions would be reduced, side-effects may be relieved, and habituation could be avoided. Several biomarkers, for example signals or activity derived …

Manufacturing And Instrumentation Of An Open End Compressed Air Shock Tube, Josue O. Ruiz

Master's Theses

Shock tubes have been used extensively to study shock wave structures and high speed flow features. The purpose of constructing this open end shock tube was to have the ability to produce shock waves in a laboratory setting but also understand the exit flow coming out which can be applied to future studies that are beyond the scope of this work. This undertaking would require that an open end shock tube be built and instrumented with PCB Integrated Circuit Piezoelectric (ICP) Pressure Sensor Model 113B24 that would then be connected to a PCB Model 482C05 Signal Conditioner with the purpose …

A Comparison Study Of Composite Laminated Plates With Holes Under Tension, Joun S. Kim

Master's Theses

A Comparison Study of Composite Laminated Plates with Holes under Tension

A study was conducted to quantify the accuracy of numerical approximations to deem sufficiency in validating structural composite design, thus minimizing, or even eliminating the need for experimental test. Error values for stress and strain were compared between Finite Element Analysis (FEA) and analytical (Classical Laminated Plate Theory), and FEA and experimental tensile test for two composite plate designs under tension: a cross-ply composite plate design of [(0/90)4]s, and a quasi-isotropic layup design of [02/+45/-45/902]s, each with a single, centered hole of 1/8” diameter, and 1/4" diameter (four sets …

Development Of A Rotordynamic Signal Processing Matlab Interface And A Two-Disk Rotor Model, David L. Baker

Master's Theses

Using MATLAB and a National Instruments data acquisition card, a signal processing program meant to monitor the behavior of rotordynamic systems in real-time was developed and tested. By using traditional analysis methods in this field of engineering, commonly desired data representations such as bode, polar, orbit, full spectrum plots were able to be produced to a very high accuracy. Additional capabilities offered by this application are slow roll compensation, synchronous and sub-synchronous filtering, and true three dimensional plotting. The verification of this program was done by comparing the results to the ones acquired with Bently Nevada’s “Automated Diagnostics for Rotating …

Rf Front End For An Integrated Silhouette Capture And Boundary Detection Frequency Modulated Continuous Wave Ultra-Wideband Radar System For The Extension Of Independent Living, Adrian Smet

Master's Theses

Limitations of current eldercare monitoring systems leave a need for new solutions. A monitoring system based on a frequency modulated continuous wave ultra-wideband short-range radar is proposed for this application. The complete proposed monitoring system is comprised of four blocks: boundary detection, silhouette capture, human identification, and data transmission. This paper develops the RF front end hardware for the silhouette capture subsystem.

System requirements are derived for the silhouette capture subsystem. An architecture for the RF front end is designed, and required individual component specifications are determined. Components are selected off the shelf or custom designed for each socket. Full …

Genealogy Extraction And Tree Generation From Free Form Text, Timothy Sui-Tim Chu

Master's Theses

Genealogical records play a crucial role in helping people to discover their lineage and to understand where they come from. They provide a way for people to celebrate their heritage and to possibly reconnect with family they had never considered. However, genealogical records are hard to come by for ordinary people since their information is not always well established in known databases. There often is free form text that describes a person’s life, but this must be manually read in order to extract the relevant genealogical information. In addition, multiple texts may have to be read in order to create …

Whitespace Exploration, Jason Lloyd Daniel

Master's Theses

As engineering systems grow in complexity so too must the design tools that we use evolve and allow for decision makers to efficiently ask questions of their model and obtain meaningful answers. The process of whitespace exploration has recently been developed to aid in engineering design and provide insight into a design space where traditional design exploration methods may fail. In an effort to further the research and development of whitespace exploration algorithms, a software package called Thalia has been created to allow for automated data collection and experimentation with the whitespace exploration methodology.

In this work, whitespace exploration is …

Computer-Aided Diagnoses (Cad) System: An Artificial Neural Network Approach To Mri Analysis And Diagnosis Of Alzheimer's Disease (Ad), Berizohar Padilla Cerezo

Master's Theses

Alzheimer’s disease (AD) is a chronic and progressive, irreversible syndrome that deteriorates the cognitive functions. Official death certificates of 2013 reported 84,767 deaths from Alzheimer’s disease, making it the 6th leading cause of death in the United States. The rate of AD is estimated to double by 2050. The neurodegeneration of AD occurs decades before symptoms of dementia are evident. Therefore, having an efficient methodology for the early and proper diagnosis can lead to more effective treatments.

Neuroimaging techniques such as magnetic resonance imaging (MRI) can detect changes in the brain of living subjects. Moreover, medical imaging techniques are the …

Alternative Mission Concepts For The Exploration Of Outer Planets Using Small Satellite Swarms, Andrew Gene Blocher

Master's Theses

Interplanetary space exploration has thus far consisted of single, expensive spacecraft missions. Mission costs are particularly high on missions to the outer planets and while invaluable, finite budgets limit our ability to perform extensive and frequent investigations of the planets. Planetary systems such as Jupiter and Saturn provide extremely complex exploration environments with numerous targets of interest. Exploring these targets in addition to the main planet requires multiple fly-bys and long mission timelines. In LEO, CubeSats have changed the exploration paradigm, offering a fast and low cost alternative to traditional space vehicles. This new mission development philosophy has the potential …

Sex Differences And The Effects Of Exercise Training On Functional Vasodilation Following Arterial Occlusion In The Balb/C Mouse Spinotrapezius, Britta Nelson

Master's Theses

Peripheral arterial occlusive disease (PAOD) often presents as intermittent claudication, which may be caused by impaired vasodilation. Impairment of resistance vessels may contribute to the pathogenesis of PAOD, and explain the poor correlation between resting blood flow and limb function. Collateral function following arterial occlusion is not well defined, however collaterals and arterialized collateral capillaries (ACCs) in male and female animal models exhibit impaired vasodilation following arterial occlusion, which can potentially be improved with exercise training. Furthermore, resistance vessels in the ischemic tree and stem are likely involved in the pathogenesis of PAOD, however the relative importance of each is …

Effects Of Support Structure Geometry On Slm Induced Residual Stresses In Overhanging Features, Ryan Baskett

Master's Theses

Selective laser melting (SLM) is a new and rapidly developing manufacturing method for producing full-density, geometrically complex metal parts. The SLM process is time and cost effective for small-scale production; however, wide-spread adoption of this technique is severely limited by residual stresses that can cause large deformations and in-process build failures. The issues associated with residual stress accumulation are most apparent in parts with overhanging features. Due to the complexity of the SLM process, the accumulation of residual stresses is difficult to assess a priori. The deformations and in-process failures caused by residual stress accumulation often lead to an expensive …

Identifying And Reducing Variability, Improving Scaffold Morphology, And Investigating Alternative Materials For The Blood Vessel Mimic Lab Electrospinning Process, Evan M. Dowey

Master's Theses

The work of the Cal Poly Tissue Engineering Lab is primarily focused on the fabrication, characterization, and improvement of “Blood Vessel Mimics” (BVMs), tissue engineered constructs used to evaluate cellular response to vascular medical devices. Currently, cells are grown onto fibrous, porous tubes made using an in-house electrospinning process from PLGA, a biocompatible co-polymer. The adhesion and proliferation of cells in a BVM is reliant on the micro-scale structure of the PLGA scaffold, and as such it is of great importance for the electrospinning process to consistently produce scaffolds of similar morphologies. Additionally, it has been shown that cell proliferation …

Early Empirical Evidence For The Effects Of Adaptive Ramp Metering On Measures Of Travel Time Reliability, Travis Charles Low

Master's Theses

Adaptive ramp metering (ARM) is a critical component of smart freeway corridors under an active traffic management portfolio. While improving capacity through smart corridors and application of proactive traffic management solutions is less costly and easier to deploy than freeway widening, conversion to smart corridors still represents a sizable investment for a state department of transportation. Early evidence of improvements following these projects can be valuable to agencies. However, in the U.S. there have been limited evaluations, of smart corridors in general and ARM in particular, based on real operational data. This thesis explores travel time reliability measures for the …

Removal Of Nitrates From Stormwater Using Nanoclays, Rubia Siddiqi

Master's Theses

Creeks and rivers are often polluted as a result of stormwater runoff that carries various contaminants in to open water bodies, causing adverse environmental and health effects. Low impact development (LID) techniques are currently employed to treat this runoff prior to discharge. Nitrate, however, is not consistently removed by these LID techniques. This study analyzed the ability of several nanoclays to remove nitrate in runoff and determined the feasibility of using them as a soil supplement for LID implementation. Six different nanoclays and HCl-treated clays were compared (pre-modified trimethyl stearyl ammonium nanoclay, pre-modified dimethyl dialkyl amine nanoclay, unmodified hydrophilic bentonite, …

Iota: Internet Of Things Assistant, Brandon M. Okumura

Master's Theses

The Internet of Things is the networking of electronic devices, or “Things”, that enables them to collect and share data, as well as interact with their physical surround- ings. Analyzing this collected data allows us to make smarter economic decisions. These interconnected networks are usually driven by low-powered micro-controllers or cheap CPUs that are designed to function optimally with very little hardware. As scale and computational requirements increase, these micro-controllers are unable to grow without being physically replaced.

This thesis proposes a system, IoTA, that assists the Internet of Things by pro- viding a shared computational resource for endpoint devices. …

Microwave Interferometry Diagnostic Applications For Measurements Of Explosives, Loren A. Kline

Master's Theses

Microwave interferometry (MI) is a Doppler based diagnostic tool used to measure the detonation velocity of explosives, which has applications to explosive safety. The geometry used in existing MI experiments is cylindrical explosives pellets layered in a cylindrical case. It is of interest to Lawrence Livermore National Labs to measure additional geometries that may be overmoded, meaning that the geometries propagate higher-order transverse electromagnetic waves. The goal of my project is to measure and analyze the input reflection from a novel structure and to find a good frequency to use in an experiment using this structure. Two methods of determining …

Measurement And Analysis Of The Physical And Climatic Distribution Environment For Air Package Shipment, David Guadagnini

Master's Theses

The modern air parcel distribution industry has significantly grown to become one of the most commonly employed methods to quickly transport goods throughout the world. Although it comes with many benefits, including higher speed, greater reliability, and tighter security, the multimodal transport system within it can expose packages to a wide variety of climatic and physical distribution hazards. In a single route of transportation, packages could be included in different types of small delivery vans, large commercial semi trucks, cargo dollies, feeder aircraft, and high altitude commercial jetliners. The varying hazard level presented during distribution could directly weaken the packaging …

Characterization Of Flexible Hybrid Electronics Using Stretchable Silver Ink And Ultra-Thin Silicon Die, Joshua A. Ledgerwood

Master's Theses

Flexible Hybrid Electronics (FHEs) offer many advantages to the future of wearable technology. By combining the dynamic performance of conductive inks, and the functionality of ultra-thinned, traditional IC technology, new FHE devices allow for development of applications previously excluded by relying on a specific type of electronics technology.

The characterization and reliability analysis of stretchable conductive inks paired with ultra-thin silicon die in theµm range was conducted. A silver based ink designed to be stretchable was screen printed on a TPU substrate and cured using box oven, conveyor convection oven, and photonic curing processes. Reliability tests were conducted including a …

Design And Construction Of 1800w Modular Multiple Input Single Output Non-Isolated Dc-Dc Converters, Angelo Miguel Asuncion Gallardo

Master's Theses

This thesis report details the design and construction of non-isolated DC-DC converters to create a Multiple Input Single Output (MISO) converter for combining multiple renewable energy sources into one single output. This MISO uses the four-switch buck-boost topology to output a single 48V from multiple nominal 24V inputs. The MISO converter implements a modular approach to deliver 1800W output power. Each module in the MISO is rated at 600W and they share the output power equally. Hardware results show that the converter produces 1800W of output power from three sources with 96.4% efficiency. Each module also demonstrates equal sharing feature …

Preliminary Investigations Into Selective Laser Melting, David Takeo Otsu

Master's Theses

Selective laser melting is a promising metallic additive manufacturing process with many potential applications in a variety of industries. Through a gracious donation made by Lawrence Livermore National Laboratory, California Polytechnic State University received and installed an SLM 125 HL selective laser melting machine in February 2017. As part of the initial setup effort, a preliminary machine verification study was conducted to evaluate the general print quality of the machine with default parameter settings. Coincidentally, the as-printed microstructure of SLM components was evaluated through nil strength fracture surface examination, an alternative to conventional polish-and-etch metallography. A diverse set of components …

Code Decomposition: A New Hope, Nupur Garg

Master's Theses

Code decomposition (also known as functional decomposition) is the process of breaking a larger problem into smaller subproblems so that each function implements only a single task. Although code decomposition is integral to computer science, it is often overlooked in introductory computer science education due to the challenges of teaching it given limited resources.

Earthworm is a tool that generates unique suggestions on how to improve the decomposition of provided Python source code. Given a program as input, Earthworm presents the user with a list of suggestions to improve the functional decomposition of the program. Each suggestion includes the lines …

A Data-Driven Approach To Cubesat Health Monitoring, Serbinder Singh

Master's Theses

Spacecraft health monitoring is essential to ensure that a spacecraft is operating properly and has no anomalies that could jeopardize its mission. Many of the current methods of monitoring system health are difficult to use as the complexity of spacecraft increase, and are in many cases impractical on CubeSat satellites which have strict size and resource limitations. To overcome these problems, new data-driven techniques such as Inductive Monitoring System (IMS), use data mining and machine learning on archived system telemetry to create models that characterize nominal system behavior. The models that IMS creates are in the form of clusters that …

Atomic Oxygen Considerations For Leo De-Orbit Trajectories Using Solar Sails, Daniel A. Fugett

Master's Theses

Solar sails have the potential to benefit many future space exploration missions, but they lack the heritage required for present-day use. To grow confidence in solar sail technology, they could be deployed on LEO satellites higher than 600 km to help de-orbit the satellite within 25 years upon mission termination. To determine how atomic oxygen would affect the solar sail, material from Lightsail-2 was tested in a thermal-energy, isotropic, atomic oxygen vacuum chamber based in the space environments laboratory in California Polytechnic State University. The sail material, aluminized Mylar, was tested for its survivability on both the coated and uncoated …