Engineering Commons^™

Implications Of Electric Vehicles On Gasoline Tax Revenues, Florida Solar Energy Center, Kevin Schleith

FSEC Energy Research Center®

This report summarizes the results of research conducted to determine if current and near future EV sales will have an impact on gasoline (gas) tax revenues as part of the Federal Highway Trust Fund (HTF). Gasoline taxes account for $31.1 billion or about 87% of the HTF. The project results were accomplished through a review of existing industry and government reports that detail fuel tax revenues and through analysis of EV sales from 2010 to 2015.

Numerical-Analytical Assessment On Solar Chimney Power Plant, Nima Fathi, Seyed Sobhan Aleyasin, Peter Vorobieff

Nima Fathi

Direct Numerical Simulation Of Cylindrical Particle-Laden Gravity Currents, ‪Nadim Zgheib, Thomas Bonometti, S. Balachandar

Mechanical Engineering Faculty Publications and Presentations

We present results from direct numerical simulations (DNS) of cylindrical particle-laden gravity currents. We consider the case of a full depth release with monodisperse particles at a dilute concentration where particle–particle interactions may be neglected. The disperse phase is treated as a continuum and a two-fluid formulation is adopted. We present results from two simulations at Reynolds numbers of 3450 and 10,000. Our results are in good agreement with previously reported experiments and theoretical models. At early times in the simulations, we observe a set of rolled up vortices that advance at varying speeds. These Kelvin–Helmholtz (K–H) vortex tubes are …

Analysis Of Capillary Flow In Interior Corners : Perturbed Power Law Similarity Solutions, Joshua Thomas Mccraney

Dissertations and Theses

The design of fluid management systems requires accurate models for fluid transport. In the low gravity environment of space, gravity no longer dominates fluid displacement; instead capillary forces often govern flow. This thesis considers the redistribution of fluid along an interior corner. Following a rapid reduction of gravity, fluid advances along the corner measured by the column length z = L(t), which is governed by a nonlinear partial differential equation with dynamical boundary conditions. Three flow types are examined: capillary rise, spreading drop, and tapered corner. The spreading drop regime is shown to exhibit column length growth L ~ …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Georgia Southern Research Focus Prompts R2 Carnegie Designation

Mapping Chemical Selection Pathways For Designing Multicomponent Alloys: An Informatics Framework For Materials Design, Srinkant Srinivasan, Scott R. Broderick, Ruifeng Zhang, Amrita Mishra, Susan B. Sinnott, Surendra Saxena, James M. Lebeau, Krishna Rajan

Department of Mechanical and Materials Engineering

A data driven methodology is developed for tracking the collective influence of the multiple attributes of alloying elements on both thermodynamic and mechanical properties of metal alloys. Cobalt-based superalloys are used as a template to demonstrate the approach. By mapping the high dimensional nature of the systematics of elemental data embedded in the periodic table into the form of a network graph, one can guide targeted first principles calculations that identify the influence of specific elements on phase stability, crystal structure and elastic properties. This provides a fundamentally new means to rapidly identify new stable alloy chemistries with enhanced high …

Turning An Organic Semiconductor Into A Low-Resistance Material By Ion Implantation, Beatrice Fraboni, Alessandra Scidà, Piero Cosseddu, Yongqiang Wang, Michael Nastasi, Silvia Milita, Annalisa Bonfiglio

Nebraska Center for Energy Sciences Research: Publications

We report on the effects of low energy ion implantation on thin films of pentacene, carried out to investigate the efficacy of this process in the fabrication of organic electronic devices. Two different ions, Ne and N, have been implanted and compared, to assess the effects of different reactivity within the hydrocarbon matrix. Strong modification of the electrical conductivity, stable in time, is observed following ion implantation. This effect is significantly larger for N implants (up to six orders of magnitude), which are shown to introduce stable charged species within the hydrocarbon matrix, not only damage as is the case …

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

University of New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Design, Manufacturing And Control Of An Advanced High-Precision Robotic System For Microsurgery, Arezoo Ebrahimi

Electronic Theses and Dissertations

Microsurgeries like ophthalmic surgery confront many challenges like limited workspace and hand motion, steady hand movements, manipulating delicate thin tissues, and holding the instrument in place for a long time. New developments in robotically-assisted surgery can highly benefits this field and facilitate those complicated surgeries. Robotic eye surgery can save time, reduce surgical complications and inspire more delicate surgical procedures that cannot be done currently by surgeon’s hands. In this thesis work, the requirements for ophthalmic surgeries were studied and based on that a robotic system with 6 DOF is proposed and designed. This robotic

system is capable of handling …

Developing And Testing An Anguilliform Robot Swimming With Theoretically High Hydrodynamic Efficiency, John B. Potts Iii

University of New Orleans Theses and Dissertations

An anguilliform swimming robot replicating an idealized motion is a complex marine vehicle necessitating both a theoretical and experimental analysis to completely understand its propulsion characteristics. The ideal anguilliform motion within is theorized to produce ``wakeless'' swimming (Vorus, 2011), a reactive swimming technique that produces thrust by accelerations of the added mass in the vicinity of the body. The net circulation for the unsteady motion is theorized to be eliminated.

The robot was designed to replicate the desired, theoretical motion by applying control theory methods. Independent joint control was used due to hardware limitations. The fluid velocity vectors in the …

A General-Purpose Multiphase/Multispecies Model To Predict The Spread, Percutaneous Hazard, And Contact Dynamics For Nonporous And Porous Substrates And Membranes, Homayun K. Navaz, Ali R. Zand, Amir Gat, Theresa S. Atkinson

Mechanical Engineering Publications

A computational model to solve the coupled transport equations with chemical reaction and phase change for a liquid sessile droplet or the contact and spread of a sessile droplet between two approaching porous or non-porous surfaces, is developed. The model is general therefore it can be applied to toxic chemicals (contact hazard), drug delivery through porous organs and membranes, combustion processes within porous material, and liquid movements in the ground. The equation of motion and the spread of the incompressible liquid available on the primary surface for transfer into the contacting surface while reacting with other chemicals (or water) and/or …

Electronic Musical Instrument To Generate Musical Tones To Imitate A Stringed Instrument, Mizuki Nakagawa, Ikuo Tanaka, Shun Takai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Provided are an electronic musical instrument, computer storage device, and method for generating tone. A sound source in an electronic musical instrument generates a first tone at a first pitch in response to a first tone generation instruction received by an input device of the electronic musical instrument. A second tone generation instruction is received to generate a second tone at a second pitch while generating the first tone at the sound source. A determination is made of a pitch difference of the first and the second pitches. The sound source is controlled to generate the second tone and to …

Guided Wave Based Integrated Structural Health Monitoring And Nondestructive Evaluation, Zhenhua Tian

Theses and Dissertations

Damage detection and health monitoring are critical for ensuring the structural safety in various fields, such as aerospace, civil and nuclear engineering. Structural health monitoring (SHM) performs online nondestructive evaluation (NDE) and can predict the structural remaining life through appropriate diagnosis and prognosis technologies. Among various SHM/NDE technologies, guided ultrasonic waves have shown great potential for fast and large area SHM/NDE, due to their sensitivity to small defects and capability to propagate long distances. Recent advances in guided wave based SHM/NDE technologies have demonstrated the feasibility of detecting damage in simple structures such as metallic plates and pipes. However, there …

Wavelet Analysis Of Periodic Error In Heterodyne Interferometry, Chao Lu

Theses and Dissertations

Heterodyne displacement measuring interferometry provides important metrology for applications requiring high resolution and accuracy. Heterodyne Michelson interferometers use a two-frequency laser source and separate the two optical frequencies into one fixed length and one variable length path via polarization. Ideally these two beams are linearly polarized and orthogonal so that only one frequency is directed toward each path. An interference signal is obtained by recombining the light from the two paths; this results in a measurement signal at the heterodyne (split) frequency of the laser source. This measurement signal is compared to the optical reference signal. Motion in the measurement …

A Multiphysics Modeling Of Solid Oxide Metal-Air Redox Battery, Md Ahsan Uddin

Theses and Dissertations

Cost-effective and large scale energy storage is essential for the growth of the future’s ‘‘green energy’’ infrastructure. Among the energy storage technologies currently being used, rechargeable batteries represent a class of advanced electrical energy storage (EES) mechanisms that can be valuable for the future renewable integration and smart grid. Rechargeable batteries have innumerous advantages over the conventional pumped hydro and compressed-air energy storage system. Now days, There are various types of rechargeable batteries available to work as an energy storage device in a smart grid but it still needs many breakthroughs to become commercially viable for stationary energy storage. First …

Bio-Inspired Design Of Mechanical Band Pass Sensor With The Ability To Scavenge Energy, Md Riaz Uddin Ahmed

Theses and Dissertations

Primary objective of this work is to introduce the multi-scale computational model for the bio-inspired acousto-ultrasonic band pass sensor that are capable of mechanically sense and/or filter wide range user defined frequencies. Selecting a particular and/or a distinct band of frequencies is essential for many applications in science engineering and technologies. For example design of sensors in chemical, biomedical and biological applications; device application for acoustic modulation by breaking the acoustic reciprocity and the sensors used in precision manufacturing applications requires sensing and/or filtering of wide range of acousto-ultrasonic frequencies. Presently, electronic devices are widely employed in commercial applications for …

Towards The Development Of A Wearable Tremor Suppression Glove, Yue Zhou

Electronic Thesis and Dissertation Repository

Patients diagnosed with Parkinson’s disease (PD) often associate with tremor. Among other symptoms of PD, tremor is the most aggressive symptom and it is difficult to control with traditional treatments. This thesis presents the assessment of Parkinsonian hand tremor in both the time domain and the frequency domain, the performance of a tremor estimator using different tremor models, and the development of a novel mechatronic transmission system for a wearable tremor suppression device. This transmission system functions as a mechatronic splitter that allows a single power source to support multiple independent applications. Unique features of this transmission system include low …

Engineering Design: Representation And Reasoning, Clive Dym, David Brown

David C. Brown

This text demonstrates that symbolic representation, and related problem-solving methods, offer significant opportunities to clarify and articulate concepts of design to give a better framework for design research and education. This edition includes recent work on design reasoning, computational design, AI in design, and design cognition, with pointers to the current literature.

A Framework For Control Of Robots With Energy Regeneration, Hanz Richter

Hanz Richter

This paper focuses on robot control problems where energy regeneration is an explicit consideration, and it proposes a methodology for modeling and control design of regenerative motion control systems. The generic model consists of a robotic manipulator where some joints are actively controlled and the remaining joints are energetically self-contained and semi-actively controlled. The model can capture various electromechanical and hydraulic actuator configurations for industrial robots and powered human-assist devices. The basic control approach consists of three steps. First, a virtual control design is conducted by any suitable means. Then, virtual control inputs are enacted by a matching law for …

Motion Control Of A Container With Slosh: Constrained Sliding Mode Approach, Hanz Richter

Hanz Richter

A constrained sliding mode control methodology developed by the author is applied to the motion control of an open container filled with liquid. The objective is to control the position of the container to meet the performance and robustness requirements, and to specify a safe operating set, i.e., the set of initial conditions from which the system can be operated without exceeding a prescribed liquid level and additional constraints. A conventional sliding mode regulator is designed first to address nominal performance in the sliding mode. Then, a robustly invariant cylinder formed as the Cartesian product of an ellipsoid, and a …

Muscle Synergies Improve Estimation Of Knee Contact Forces During Walking, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

This study investigates whether use of subject-specific muscle synergies can improve optimization predictions of muscle excitation patterns and knee contact forces during walking. Muscle synergies describe how a small number of neural commands generated by the nervous system can be linearly combined to produce the broad range of muscle electromyographic (EMG) signals measured experimentally. By quantifying the interdependence of individual EMG signals, muscle synergies provide dimensionality reduction for the neural control redundancy problem. Our hypothesis was that use of subjectspecific muscle synergies to limit muscle excitation patterns would improve prediction of muscle EMG patterns at the hip, knee, and ankle …

Muscle Synergy Constraints Improve Prediction Of Knee Contact Force During Gait, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

Knowledge of patient-specific muscle and joint contact forces during activities of daily living could improve the treatment of movement-related disorders (e.g., osteoarthritis, stroke, cerebral palsy, Parkinson’s disease). Unfortunately, it is currently impossible to measure these quantities directly under common clinical conditions, and calculation of these quantities using computer models is limited by the redundant nature of human neural control (i.e., more muscles than theoretically necessary to actuate the available degrees of freedom in the skeleton). Walking is a particularly important task to understand, since loss of mobility is associated with increased morbidity and decreased quality of life. Though numerous musculoskeletal …

Evaluation Of Different Optimal Control Problem Formulations For Solving The Muscle Redundancy Problem, Friedl De Groote, Allison Kinney, Anil Rao, Benjamin Fregly

Allison Kinney

This study evaluates several possible optimal control problem formulations for solving the muscle redundancy problem with the goal of identifying the most efficient and robust formulation. One novel formulation involves the introduction of additional controls that equal the time derivative of the states, resulting in very simple dynamic equations. The nonlinear equations describing muscle dynamics are then imposed as algebraic constraints in their implicit form, simplifying their evaluation. By comparing different problem formulations for computing muscle controls that can reproduce inverse dynamic joint torques during gait, we demonstrate the efficiency and robustness of the proposed novel formulation.

Material Properties And Microstructural Characterization Of Specimens, T.J. Silverman, Allison Kinney, B. South, W. Yong, J.H. Koo

Allison Kinney

The HiQ upgrade to the 3D Systems Vanguard selective laser sintering (SLS) machine incorporates a revised thermal calibration system and new software. This paper quantifies differences in mechanical and morphological properties of specimens built first using a Vanguard HS (high-speed) system and again using the same system with the HiQ upgrade applied. Standard specimens are built from DuraForm PA material and tested for tensile modulus, tensile strength, elongation at break, flexural modulus and Izod impact strength. The design of the specimen battery, the conduction of the tests and the significance of the results are discussed. The upgrade is found to …

Synergies Controls Improve Prediction Of Knee Contact Forces And Muscle Excitations During Gait, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

This study investigates whether use of muscle excitation controls constructed from subjectspecific muscle synergy information can improve optimization prediction of knee contact forces and muscle excitations during walking. Muscle synergies quantify how a large number of experimental muscle electromyographic (EMG) signals can be reconstructed by linearly mixing a much smaller number of neural commands generated by the nervous system. Our hypothesis was that controlling all muscle excitations with a small set of experimentally calculated neural commands would improve prediction of knee contact forces and leg muscle excitations compared to using independently controlled muscle excitations.

Comparison Of Material Properties And Microstructure Of Specimens Built Using The 3d Systems Vanguard Hs And Vanguard Hiq+Hs Sls Systems, T.J. Silverman, Allison Kinney, W. Yong, J.H. Koo

Allison Kinney

The HiQ upgrade to the 3D Systems Vanguard selective laser sintering (SLS) machine incorporates a revised thermal calibration system and new control software. The paper compares the tensile modulus, tensile strength, elongation at break, flexural modulus, Izod impact resistance and microstructure of two batteries of standard specimens built from recycled Duraform PA (Nylon 12). The first set is built on a Vanguard HS system and the second on the same system with the HiQ upgrade installed. The upgrade reduces user intervention, decreases total build time and improves surface finish. However, using the default processing parameters, tensile, flexure and impact properties …

Comparing Mathematical And Heuristic Approaches For Scientific Data Analysis, Aparna Varde, Shuhui Ma, Mohammed Maniruzzaman, David Brown, Elke Rundensteiner, Richard Sisson

David C. Brown

Scientific data is often analyzed in the context of domain-specific problems, for example, failure diagnostics, predictive analysis, and computational estimation. These problems can be solved using approaches such as mathematical models or heuristic methods. In this paper we compare a heuristic approach based on mining stored data with a mathematical approach based on applying state-of-the-art formulae to solve an estimation problem. The goal is to estimate results of scientific experiments given their input conditions. We present a comparative study based on sample space, time complexity, and data storage with respect to a real application in materials science. Performance evaluation with …

U.S. Billion-Ton Update: Biomass Supply For A Bioenergy And Bioproducts Industry, Robert D. Perlack, Laurence M. Eaton, Anthony F. Turhollow Jr., Matt H. Langholtz, Craig C. Brandt, Mark E. Downing, Robin L. Graham, Lynn L. Wright, Jacob M. Kavkewitz, Anna M. Shamey, Richard G. Nelson, Bryce J. Stokes, William L. Rooney, David J. Muth Jr., J. Richard Hess, Jared M. Abodeely, Chad Hellwinckel, Danial De La Torre Ugarte, Daniel C. Yoder, James P. Lyon, Timothy G. Rials, Timothy A. Volk, Thomas S. Buchholz, Lawrence P. Abrahamson, Robert P. Anex, Thomas B. Voigt, William Berguson, Don E. Riemenschneider, Douglas Karlen, Jane M. F. Johnson, Robert B. Mitchell, Kenneth P. Vogel, Edward P. Richard Jr., John Tatarko, Larry E. Wagner, Kenneth E. Skog, Patricia K. Lebow, Dennis P. Dykstra, Marilyn A. Buford, Patrick D. Miles, D. Andrew Scott, James H. Perdue, Robert B. Rummer, Jamie Barbour, John A. Stanturf, David B. Mckeever, Ronald S. Zalesny Jr., Edmund A. Gee, P. Daniel Cassidy, David Lightle

Douglas L Karlen

The Report, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply (generally referred to as the Billion-Ton Study or 2005 BTS), was an estimate of “potential” biomass within the contiguous United States based on numerous assumptions about current and future inventory and production capacity, availability, and technology. In the 2005 BTS, a strategic analysis was undertaken to determine if U.S. agriculture and forest resources have the capability to potentially produce at least one billion dry tons of biomass annually, in a sustainable manner—enough to displace approximately 30% of the country’s present petroleum …

Probing The Roles Of Polymeric Separators In Lithium-Ion Battery Capacity Fade At Elevated Temperatures, Jianchao Chen, Yongda Yan, Tao Sun, Yue Qi, Xiaodong Li

Xiaodong Li

The high temperature mechanical property of separators is very important for safety of lithium-ion batteries. However, the mechanical integrity of polymeric separators in lithium-ion batteries at elevated temperatures is still not well characterized. In this paper, the temperature dependent micro-scale morphology change of PP (polypropylene)-PE (polyethylene)-PP sandwiched separators (Celgard 2325) was studied by in-situ high temperature surface imaging using an atomic force microscope (AFM) coupled with power spectral density (PSD) analysis and digital image correlation (DIC) technique. Both PSD and DIC analysis results show that the PP phase significantly closes its pores by means of dilation of the nanofibrils surrounding …

Probing The Roles Of Polymeric Separators In Lithium-Ion Battery Capacity Fade At Elevated Temperatures, Jianchao Chen, Yongda Yan, Tao Sun, Yue Qi, Xiaodong Li

Xiaodong Li

The high temperature mechanical property of separators is very important for safety of lithium-ion batteries. However, the mechanical integrity of polymeric separators in lithium-ion batteries at elevated temperatures is still not well characterized. In this paper, the temperature dependent micro-scale morphology change of PP (polypropylene)-PE (polyethylene)-PP sandwiched separators (Celgard 2325) was studied by in-situ high temperature surface imaging using an atomic force microscope (AFM) coupled with power spectral density (PSD) analysis and digital image correlation (DIC) technique. Both PSD and DIC analysis results show that the PP phase significantly closes its pores by means of dilation of the nanofibrils surrounding …