Engineering Commons^™

Separation Control On High Lift Low-Pressure Turbine Airfoils Using Pulsed Vortex Generator Jets, Ralph J. Volino, Mounir B. Ibrahim

Mechanical Engineering Faculty Publications

Boundary layer separation control has been studied using vortex generator jets (VGJs) on a very high lift, low-pressure turbine airfoil. Experiments were done under low (0.6%) freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Instantaneous velocity profile measurements were acquired in the suction surface boundary layer. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) of 25000 and 50000. Jet pulsing frequency and duty cycle were varied. In cases without …

Comparison Of 4d Phase-Contrast Mri Flow Measurements To Computational Fluid Dynamics Simulations Of Cerebrospinal Fluid Motion In The Cervical Spine, Theresia Yiallourou, Jan Robert Kroger, Nikolaos Stergiopulos, David Maintz, Bryn A. Martin, Alexander C. Bunck

Mechanical Engineering Faculty Research

Cerebrospinal fluid (CSF) dynamics in the cervical spinal subarachnoid space (SSS) have been thought to be important to help diagnose and assess craniospinal disorders such as Chiari I malformation (CM). In this study we obtained time-resolved three directional velocity encoded phase-contrast MRI (4D PC MRI) in three healthy volunteers and four CM patients and compared the 4D PC MRI measurements to subject-specific 3D computational fluid dynamics (CFD) simulations. The CFD simulations considered the geometry to be rigid-walled and did not include small anatomical structures such as nerve roots, denticulate ligaments and arachnoid trabeculae. Results were compared at nine axial planes …

Stress And Strain Adaptation In Load-Dependent Remodeling Of The Embryonic Left Ventricle, Christine Buffinton

Faculty Journal Articles

Altered pressure in the developing left ventricle (LV) results in altered morphology and tissue material properties. Mechanical stress and strain may play a role in the regulating process. This study showed that confocal microscopy, three-dimensional reconstruction, and finite element analysis can provide a detailed model of stress and strain in the trabeculated embryonic heart. The method was used to test the hypothesis that end-diastolic strains are normalized after altered loading of the LV during the stages of trabecular compaction and chamber formation. Stage-29 chick LVs subjected to pressure overload and underload at stage 21 were reconstructed with full trabecular morphology …

High Performance Low Temperature Solid Oxide Fuel Cells With Novel Electrode Architecture, Yu Chen, Qian Liu, Zhibin Yang, Fanglin Chen, Minfang Han

Faculty Publications

In this study, we have fabricated high performance low temperature solid oxide fuel cells (LT-SOFCs) with both acicular anodes and cathodes with thin Gd-doped ceria (GDC) electrolyte film. The acicular Ni-Gd_0.1Ce_0.9O_2−δ (Ni-GDC) anode was prepared using freeze drying tape casting, while the hierarchically porous cathode with nano-size Sm_0.5Sr_0.5CoO₃ (SSC) particles covering an acicular GDC skeleton was prepared by a combination of freeze drying tape casting and self-rising approaches. The acicular electrodes with 5–200 μm pores/channels enhance mass transport, while SSC particles of about 50 nm in the cathode promote …

A Building Energy Efficiency Optimization Method By Evaluating The Effective Thermal Zones Occupancy, Anna Laura Pisello, Michael Bobker, Franco Cotana

Publications and Research

Building energy efficiency is strongly linked to the operations and control systems, together with the integrated performance of passive and active systems. In new high quality buildings in particular, where these two latter aspects have been already implemented at the design stage, users’ perspective, obtained through post-occupancy assessment, has to be considered to reduce whole energy requirement during service life. This research presents an innovative and low-cost methodology to reduce buildings’ energy requirements through post-occupancy assessment and optimization of energy operations using effective users’ attitudes and requirements as feedback. As a meaningful example, the proposed method is applied to a …

Effects Of Crossflow Velocity And Transmembrane Pressure On Microfiltration Of Oil-In-Water Emulsions, Nikolai V. Priezjev, Tohid Darvishzadeh

Mechanical and Materials Engineering Faculty Publications

This study addresses the issue of oil removal from water using hydrophilic porous membranes. The effective separation of oil-in-water dispersions involves high flux of water through the membrane and, at the same time, high rejection rate of the oil phase. The effects of transmembrane pressure and crossflow velocity on rejection of oil droplets and thin oil films by pores of different cross-section are investigated numerically by solving the Navier-Stokes equation. We found that in the absence of crossflow, the critical transmembrane pressure, which is required for the oil droplet entry into a circular pore of a given surface hydrophilicity, agrees …

College Of Engineering Senior Design Competition Fall 2012, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Senior Design Experience

Part of every UNLV engineering student's academic experience, the Senior Design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. Working in teams, the senior design project encourages students to use everything learned in the engineering and computer design programs to create a practical, real world solution to an engineering challenge.

Beyond the classroom ...

Because of the requirement to work in teams, students also build good communication skills, presentation skills and even business writing skills. They also have to …

Integrating Qplm And Biomedical Test Data With An Anisotropic Fiber Distribution Model And Predictions Of Tgf-Β1 And Igf-1 Regulation Of Articular Cartilage Fiber Modulus, Michael E. Stender, Christopher B. Raub, Kevin A. Yamauchi, Reza Shirazi, Pasquale Vena, Robert L. Sah, Scott J. Hazelwood, Stephen M. Klisch

Mechanical Engineering

A continuum mixture model with distinct collagen (COL) and glycosaminoglycan elastic constituents was developed for the solid matrix of immature bovine articular cartilage. A continuous COL fiber volume fraction distribution function and a true COL fiber elastic modulus ( Ef) were used. Quantitative polarized light microscopy (qPLM) methods were developed to account for the relatively high cell density of immature articular cartilage and used with a novel algorithm that constructs a 3D distribution function from 2D qPLM data. For specimens untreated and cultured in vitro, most model parameters were specified from qPLM analysis and biochemical assay results; consequently, Ef was …

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

Me-Em Enewsbrief, December 2012, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

Loss Enhanced Transmission And Collimation In Anisotropic Epsilon-Near-Zero Metamaterials, L. Sun, S. Feng, Xiaodong Yang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We verify the extraordinary transmission enhancement and collimation induced by the material loss in anisotropic epsilon-near-zero metamaterials, and reveal the physical mechanism of this exotic electromagnetic phenomenon via the iso-frequency contour analysis. In addition, we demonstrate the possibility in realization of such loss enhanced transmission of Gaussian beam in realistic silver-germanium multilayered structures by applying full-wave numerical simulations.

Energy Trapping Of Thickness-Shear And Thickness-Twist Modes In A Partially Electroded At-Cut Quartz Resonator, Huijing He, Guoquan Nie, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

The thickness-shear and thickness-twist vibrations of a finite and partially electroded AT-cut quartz resonator are investigated. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the free vibration resonant frequencies, mode shapes, and energy trapping are calculated and examined.

Sustainability For Die Manufacturing: Comparative Study Of Wedm And Milling, Matthew S. Kalus

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Sustainability is more important in today's culture due to the increasing demand for a more eco-friendly society. Concentrations in minimizing and reducing environmental impacts, energy and natural resources have been forthcoming in industry. The tool, mold and die industries are the most well known industries that machine harder materials using mills and WEDM. The objective of this thesis was to compare the sustainability differences in both of these machines utilizing the accepted standards for evaluating the manufacturing process performance for sustainability. These standards include the evaluation of the process parameters, raw materials, power, tools and fluids which all contribute to …

A Study Of Hdpe In High Pressure Of Hydrogen Gas—Measurement Of Permeation Parameters And Fracture Criteria, Sompong Prachumchon

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The permeation parameters of hydrogen gas in high density polyethylene (HDPE) system are sought by comparison with a diffusion model. The method of Green’s functions is used to obtain solutions for the diffusion model. Permeation parameters are found from transient experimented data during two processes; pressurization followed by depressurization. The mechanical compression of HDPE during the pressurization process resulted in lower diffusivity coefficient values and higher solubility values. The results show that the diffusivity coefficient value in the pressurization process is 37% of that during the depressurization process. At the start of the depressurization process, a short-duration fast flow rate …

Rotor Model Updating And Validation For An Active Magnetic Bearing Based High-Speed Machining Spindle, Adam C. Wroblewski, Jerzy T. Sawicki, Alexander H. Pesch

Mechanical Engineering Faculty Publications

This paper presents an experimentally driven model updating approach to address the dynamic inaccuracy of the nominal finite element (FE) rotor model of a machining spindle supported on active magnetic bearings. Modeling error is minimized through the application of a numerical optimization algorithm to adjust appropriately selected FE model parameters. Minimizing the error of both resonance and antiresonance frequencies simultaneously accounts for rotor natural frequencies as well as for their mode shapes. Antiresonance frequencies, which are shown to heavily influence the model’s dynamic properties, are commonly disregarded in structural modeling. Evaluation of the updated rotor model is performed through comparison …

Modular Joystick Design For Virtual Reality Surgical Skills Training, Michael Head

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A modular control interface and simulated virtual reality environment was designed and created in order to determine how the kinematic architecture of a control interface affects minimally invasive surgery. A user is able to selectively determine how many, the type, and location of degrees of freedom they require for the specific surgical simulation through the use of modular joints and constraint components. Furthermore, passive locking was designed and implemented through the use of inflated latex tubing around rotational degree of freedom joints. It is believed these features will have the ability to effectively simulate a variety of surgical simulations and …

Cable Median Barrier Failure Analysis And Remediation, Cody S. Stolle

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

On divided roadways, cross-median fatalities are disproportionately overrepresented in fatal and serious injury crashes. Many state DOTs sought to mitigate cross-median crash risk by installing cable median barriers. Despite increased crash rates, studies evaluating crash rates before and after cable median barriers were installed indicated excellent improvement in overall safety.

Although cable median barriers are intended to prevent serious cross-median crashes, cable barriers can also contribute to serious injury and fatality crashes which would not have otherwise occurred, including penetration and rollover crashes. In order to reduce the frequency of undesirable penetration and rollover crashes occurring with cable median barriers …

Predicting Vehicle Dynamics For Roadside Safety Using Multibody Systems Simulations, Brett D. Schlueter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Accurate means for predicting vehicle dynamics is required in the design and testing of roadside safety hardware. Past research has used finite element (FE) modeling to this end, but multibody systems (MBS) modeling may provide a more efficient way to solve these problems. MBS modeling using Adams/Car was investigated by first compiling an introduction to the program, then performing basic vehicle dynamics simulations using a supplied model. Next, a model of a 2270 kg pickup was created and validated against physical test data involving impact with a speed bump. Finally, pickup trajectories in 4H:1V and 6H:1V V-ditches were predicted for …

Compression Transmission Collar For Fastening, David Lecronier, Patrick Atkinson

Mechanical Engineering Patents

A compression transmission collar apparatus for implantation into a bone with a hole having a hole wall comprising an intramedullary nail defining a bore and a threaded fastener and a compression transmission collar including an exterior face and a top edge and a bottom edge and a first end interstcting the top edge at an acute angle and the bottom edge at an obtuse angle and a second end intersecting the top edge at an obtuse angle and the bottom edge at an acute angle and the first end partially overlapping and opposing the second end to define a slit …

Can Silver Be A Reliable Current Collector For Electrochemical Tests?, Yunhui Gong, Changyong Qin, Kevin Huang

Faculty Publications

The true functionality of a current collector employed in electrochemical cells is to ensure a low- resistance steady electrons flow between the cell and instrumentation without involving in any local electrochemical reactions of the electrode. In this study, we investigated the effect of curing temperature of a common current collector, silver, on the polarization area specific resistance (ASR) of a cathode. The results explicitly showed that at least one order of magnitude lower ASR for a cathode with Ag cured at 800°C than that cured at 650°C of the same cathode configuration. Microscopic analysis of the 800°C-cured cells revealed a …

Chemical Vapor-Deposited Carbon Nanofibers On Carbon Fabric For Supercapacitor Electrode Applications, Yang Gao, Gaind P. Pandey, James Turner, Charles R. Westgate, Bahgat Sammakia

Mechanical Engineering Faculty Scholarship

Entangled carbon nanofibers (CNFs) were synthesized on a flexible carbon fabric (CF) via water-assisted chemical vapor deposition at 800A degrees C at atmospheric pressure utilizing iron (Fe) nanoparticles as catalysts, ethylene (C2H4) as the precursor gas, and argon (Ar) and hydrogen (H-2) as the carrier gases. Scanning electron microscopy, transmission electron microscopy, and electron dispersive spectroscopy were employed to characterize the morphology and structure of the CNFs. It has been found that the catalyst (Fe) thickness affected the morphology of the CNFs on the CF, resulting in different capacitive behaviors of the CNF/CF electrodes. Two different Fe thicknesses (5 and …

Experimental Studies And Dynamics Modeling Analysis Of The Swimming And Diving Of Whirligig Beetles (Coleoptera: Gyrinidae), Zhonghua Xu, Scott C. Lenaghan, Benjamin E. Reese, Xinghua Jia, Mingjun Zhang

Faculty Publications and Other Works -- Mechanical, Aerospace and Biomedical Engineering

Whirligig beetles (Coleoptera, Gyrinidae) can fly through the air, swiftly swim on the surface of water, and quickly dive across the air-water interface. The propulsive efficiency of the species is believed to be one of the highest measured for a thrust generating apparatus within the animal kingdom. The goals of this research were to understand the distinctive biological mechanisms that allow the beetles to swim and dive, while searching for potential bio-inspired robotics applications. Through static and dynamic measurements obtained using a combination of microscopy and high-speed imaging, parameters associated with the morphology and beating kinematics of …

Cost Effectiveness Of Home Energy Retrofits In Pre-Code Vintage Homes In The United States, Florida Solar Energy Center, Philip Fairey

FSEC Energy Research Center®

This study investigates the cost effectiveness of a large number of potential home energy retrofit measures using pre-code home archetypes that can be considered typical in a range of climates throughout the United States.

Droplet Spray Behavior Of An Atomization-Based Cutting Fluid (Acf) System For Machining Of Titanium Alloys, Chandra Nath, Shiv G. Kapoor, Anil K. Srivastava, Jon Iverson

Manufacturing & Industrial Engineering Faculty Publications and Presentations

The aim of this research is to study droplet spray characteristics of an atomization-based cutting fluid (ACF) spray system including droplet entrainment angle and flow development regions with respect to three ACF spray parameters, viz., droplet and gas velocities, and spray distance. ACF spray experiments are performed by varying droplet and gas velocities. The flow development behavior is studied by modeling the droplets entrainment mechanism, and the density and distribution of the droplets across the jet flare. Machining experiments are also performed in order to understand the effect of the droplet spray behavior on the machining performances, viz., tool life/wear, …

Managing The Drivers Of Airflow And Water Vapor Transport In Existing Single-Family Homes (Revised), Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

Air and water vapor are transported into and within single-family homes as a result of pathways and driving forces. Without pathways, no air or water vapor transport could occur. Likewise, without driving forces, little or no air or water vapor transport will occur. Homes always have pathways and driving forces. This report focuses on managing the driving forces that move air and water vapor across the building envelope.

Work In Progress: Outreach Assessment: Measuring Engagement, Lizabeth Schlemer, John Oliver, Katherine Chen, Sophia Rodriguez Mata, Eric Kim

Industrial and Manufacturing Engineering

The Learn By Doing Lab (LBDL) at Cal Poly, San Luis Obispo is an on-campus laboratory where 5th through 8th grade students are taught by undergraduates who may be planning a careers in teaching. The two populations - elementary students and undergraduates - are equally important in the process. Since 2008, the lab has seen over 4000 elementary and junior high students and over 100 undergrads have participated. In most outreach assessment the number of individuals participating is an important metric, but this last Spring we experimented with a more in depth measure of effectiveness. As in any learning experience …

Multi-Objective Optimization Of Wind Farm Layouts Under Energy Generation And Noise Propagation, Cristina Amon, Wing Yin Kwong, Joaquin Moran, Michael Morgenroth, David Romeo, Peter Y. Zhang

Publications and Scholarship

Wind farm design deals with the optimal placement of turbines in a wind farm. Past studies have focused on energymaximization, cost-minimization or revenue-maximization objectives. As land is more extensively exploited for onshore wind farms, wind farms are more likely to be in close proximity with human dwellings. Therefore governments, developers, and landowners have to be aware of wind farms’ environmental impacts. After considering land constraints due to environmental features, noise generation remains the main environmental/health concern for wind farm design. Therefore, noise generation is sometimes included in optimization models as a constraint. Here we present continuous-location models for layout optimization …

2012 (Fall) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the fall of 2012.

Designing For Success: Developing Engineers Who Consider Universal Design Principles, Kimberly Edginton Bigelow

Mechanical and Aerospace Engineering Faculty Publications

Engineers must design for a diverse group of potential users of their products; however, engineering curricula rarely include an emphasis on universal design principles. This research article details the effectiveness of a design project implemented in a first-year engineering course in an effort to raise awareness of the need for engineers to be more inclusive when designing. Students were asked to apply universal design principles to redesign an engineering laboratory to make it more usable to all, including individuals with disabilities who use the room. A representative from the university’s disability services staff, as well as individuals with first-hand experience …

Enhancing The Engineering Curriculum: Defining Discovery Learning At Marquette University, Jay R. Goldberg, Mark L. Nagurka

Biomedical Engineering Faculty Research and Publications

This paper summarizes the results of our investigation into the feasibility of increasing the level of discovery learning in the College of Engineering (COE) at Marquette University. We review the education literature, document examples of discovery learning currently practiced in the COE and other schools, and propose a Marquette COE-specific definition of discovery learn-ing. Based on our assessment of the benefits, costs, and tradeoffs associated with increasing the level of discovery learning, we pre-sent several recommendations and identify resources required for implementation. These recommendations may be helpful in enhancing engineering education at other schools.