Engineering Commons^™

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

The Effects Of Influent Debit On Hydrodynamic Characteristic Of Bojongsoang Facultative Pond: Without Wind Effects, Rositayanti Hadisoebroto, Suprihanto Notodarmojo

Makara Journal of Technology

The Effects of Influent Debit on Hydrodynamic Characteristic of Bojongsoang Facultative Pond: Without Wind Effects. The performance of facultative pond in Bojongsoang WWTP have reported to be unstable. One of the cause of the unstable performance is the hydrodynamic characteristics that not met the criterion. The improper hydrodynamic characteristics are included the existence of dead-zone, the short-circuiting, and the turbulence due to eddy current. The study was to analyze the effect of the influent debit variation on the hydrodynamic characteristics of the pond using mathematical model. The two-dimensional hydrodynamic model was built from two hydrodynamic equations which are continuity and …

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …

Modelling And Simulation Of Packed Bed Catalytic Converter For Oxidation Of Soot In Diesel Powered Vehicles Flue Gas, Mohammad Nasikin, Praswasti P.D.K. Wulan, Vita Andrianty

Makara Journal of Technology

Modelling and Simulation of Packed Bed Catalytic Converter for Oxidation of Soot in Diesel Powered Vehicles Flue Gas. Diesel vehicle is used in Indonesia in very big number. This vehicle exhausts pollutants especially diesel soot that can be reduces by using a catalytic converter to convert the soot to CO2. To obtain the optimal dimension of catalytic converter it is needed a model that can represent the profile of soot weight, temperature and pressure along the catalytic converter. In this study, a model is developed for packed bed catalytic converter in an adiabatic condition based on a kinetic study that …

Fuel Injection System For One Cylinder Motor Cycle Engine, Bambang Sugiarto

Makara Journal of Technology

Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel …

A Method For Winding Advanced Composites Of Unconventional Shapes Using Continuous And Aligned Fibers, Abraham K. Allen

Theses and Dissertations

Advanced composites are extremely strong, rigid, and light, even when compared with advanced metals. Advanced composites are replacing high-tech metals as the material of choice for aerospace engineering. However, the processes used to manufacture advanced composites generally lose some of the properties of the materials by their process limitations.

One process that keeps the theoretically awesome qualities of the composite materials in tact is filament winding. Filament wound parts are used as rocket shells, bicycle frame tubes, drive shafts, pressure vessels, etc. Filament winding is an automated process and makes reliable parts to close tolerances. If a straight tube were …

Byu Micro-Sar: A Very Small, Low-Power Lfm-Cw Synthetic Aperture Radar, Michael Israel Duersch

Theses and Dissertations

Brigham Young University has developed a low-cost, light-weight, and low power consumption SAR for flight on a small unmanned aerial vehicle (UAV) at low altitudes. This micro-SAR, or uSAR, consumes only 18 watts of power, ideal for application on a small UAV. To meet these constraints, a linear frequency modulation-continuous wave (LFM-CW) transmit signal is utilized. Use of an LFM-CW signal introduces some differences from the typical strip map SAR processing model that must be addressed in signal processing algorithms. This thesis presents a derivation of the LFM-CW signal model and the associated image processing algorithms used for the uSAR …

2004 Supplement To The Standard For Cold-Formed Steel Framing – Prescriptive Method For One And Two Family Dwellings, 2001 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Aisi Standard For Cold-Formed Steel Framing – General Provisions, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary. With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

Aisi Standard For Cold-Formed Steel Framing – Wall Stud Design, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary. With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

Standard For Cold-Formed Steel Framing – General Provisions, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

2004 Supplement To The Standard For Cold-Formed Steel Framing Prescriptive - Method For One And Two Family Dwellings, 2001 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

Commentary On The Standard For Cold-Formed Steel Framing Prescriptive Method For One And Two Family Dwellings, 2001 Edition With 2004 Supplement, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is anticipated that AISI will publish updates of …

Standard For Cold-Formed Steel Framing -- Prescriptive Method For One And Two Family Dwellings, 2001 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is anticipated that AISI will publish updates of …

Standard For Cold-Formed Steel Framing – Wall Stud Design, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

Investigation Of Disinfection Byproduct Precursors In The Wachusett Reservoir Watershed, Darleen P. Bryan

Environmental & Water Resources Engineering Masters Projects

The disinfection of drinking water with chlorine was implemented as early as 1908 in an effort to inactivate water borne pathogens. However, chlorine reacts with naturally occurring organic' matter in water to form a host of chlorination byproducts. The possible detrimental health effects from exposure to these byproducts lead to the development offederal regulations for disinfection byproducts (DBPs) in drinking water. Most recently, standards were reduced to 80 ug/L for trihalomethanes, and 60 ug/L for haloacetic acids. The drinking water supplied by the Massachusetts Water Resources Authority (MWRA) has approached and sometimes exceeded the concern level at a few locations …

Simulation Of Evapotranspiration And Rainfall-Runoff For The Stillwater River Watershed In Central Massachusetts, Kavitha M. Ambikadevi

Environmental & Water Resources Engineering Masters Projects

Preliminary studies were conducted on the application of the TOPMODEL to the 3.1.6 me Stillwater River watershed in the Wachusett reservoir basin. TOPMODEL is a physically based - semi distributed hydrological model, which simulates rainfall runoff at a daily or sub-daily time steps. TOPMODEL, version 95.02 was used for the modeling studies. This version of TOPMODEL assumes an exponential transmissivity function for the soil and a first order hyperbolic recession curve for the baseflow. TOPMODEL estimates runoff as the sum of base flow, inflltration "excess overland flow and saturation excess overland flow. Inflltration excess overland flow is modeled using the …

My Life With Polymer Science: Scientific And Personal Memoirs, Otto Vogl

Emeritus Faculty Author Gallery

My "life story" will begin with my formative years, my childhood and student days at the University of Vienna, including my dissertation. It will be followed by my teaching appointment as an Instructor at the II. Chemical Institute of the University of Vienna. The urge to see other lands, learn other languages and scientific methods led to the Wandering Years that brought me to the United States. After three years spent as a Research Associate at the University of Michigan and at Princeton University I spent more than 13 years in an industrial career at the Du Pont Company in …

Characterization Of Porous Media And Refractory Materials, Xin Chen

Doctoral Dissertations

Because of its unique advantages on energy savings and casting complex shaper, Lost Foam Casting (LFC) has been widely used as a replacement to the conventional techniques (sand and investment castings). In order to continuously improve the quality of the Lost Foam Casting process for reducing scrap rate and increasing energy savings, the US Department of Energy through its National Industrial Competitiveness through Energy, Environment, and Economics (NICEEE) program sponsored the present study to develop new characterization techniques for enhancing the understanding of the fundamental properties of the refractory materials used in The Lost Foam Casting process. In this study, …

An Adaptive Tool-Based Telerobot Control System, Ge Zhang

Doctoral Dissertations

Modern telerobotics concepts seek to improve the work efficiency and quality of remote operations. The unstructured nature of typical remote operational environments makes autonomous operation of telerobotic systems difficult to achieve. Thus, human operators must always remain in the control loop for safety reasons. Remote operations involve tooling interactions with task environment. These interactions can be strong enough to promote unstable operation sometimes leading to system failures. Interestingly, manipulator/tooling dynamic interactions have not been studied in detail. This dissertation introduces a human-machine cooperative telerobotic (HMCTR) system architecture that has the ability to incorporate tooling interaction control and other computer assistance …

Convergence And Robustness Issues In Computational Fluids, Xiaoqiang Zeng

Doctoral Dissertations

The present research develops two methods to improve the convergence and robustness of CFL algorithm, the triple time method and error- limited time step ramping method.

A general formulation of the triple time scheme is developed by introducing three pseudo time-marching steps to control three preconditionings for artificial dissipation, non-linear equation iteration convergence and linear equation iteration convergence separately. It is proven that the triple time method can be degenerated to the single time method and the multiple DDLGS iteration method at special cases.

Stability analysis is used to choose the optimum combination of three preconditionings from the steady preconditioning, …

High Accuracy Distributed Target Detection And Classification In Sensor Networks Based On Mobile Agent Framework, Xiaoling Wang

Doctoral Dissertations

High-accuracy distributed information exploitation plays an important role in sensor networks. This dissertation describes a mobile-agent-based framework for target detection and classification in sensor networks. Specifically, we tackle the challenging problems of multiple- target detection, high-fidelity target classification, and unknown-target identification.

In this dissertation, we present a progressive multiple-target detection approach to estimate the number of targets sequentially and implement it using a mobile-agent framework. To further improve the performance, we present a cluster-based distributed approach where the estimated results from different clusters are fused. Experimental results show that the distributed scheme with the Bayesian fusion method have better performance …

Synthesis And Ordering Of Nanostructures Using Laser Light, Yingfeng Guan

Doctoral Dissertations

This dissertation focuses on the formation of 1-D and 2-D nanoscale structures induced by the KrF excimer UV laser irradiation of silicon (λ=248 nm). Relatively low laser energy density (E_d<=1 J/cm²) is required to produce nanostructures. Alignment of 2-D nanoripple structures and nanoprotrusions has been realized by using Lloyd’s mirror configuration.

Laser-generated silicon microcone arrays were used as templates for the growth of nanocolumns. The formation mechanism of the microstructure is reviewed, and the origin and growth of nanocolumns are discussed. The formation mechanism of nanocolumns requires highly localized melting, which explains why they fail to form on …

A Study Of The Evolution Of Laser-Induced Periodic Surface Microstructures On Silicon And Electronic Transport In Composite Carbon Nanotube Networks, Stephen Jesse

Doctoral Dissertations

This dissertation addresses two main topics, the formation of micron-scale surface structures on single crystal silicon by irradiation with a KrF (248 nm) pulsed excimer laser source, and an investigation into electronic transport through composites of polymer (PMMA) and single-walled carbon nanotubes. It is shown that the spacing between laser-generated surface structures is determined primarily by the melt time and that the crystal orientation of the substrate can determine whether surface structures will form at all and also influence the shape of individual surface structures. During the melt/solidification cycle, the shape of liquid-vapor interface in modified by surface tension, and …

Fundamental Studies Of X-Ray And Secondary Electron Spectroscopy, Staya Prasad Mulapudi

Doctoral Dissertations

Microanalysis of submicron particles in the Scanning Electron Microscope (SEM) is only possible by using low incident electron beam energies due to smaller interaction volume and suppressed beam induced charging. Such low beam energies must use L- and M- lines rather than the familiar K-lines. The information about the fundamental parameters of X-ray emission and transport at low energies is limited, so the use of L- and M- lines is problematic. The rate of generation of X-rays from an element irradiated at some energy E depends on the product of the ionization cross-section (E) and the fluorescent yield . Unfortunately …

Modeling And Source Apportionment Of Primary And Secondary Pm2.5 In The Atmosphere, Prakash Doraiswamy

Doctoral Dissertations

Source apportionment of PM_2.5 is important to identify the source categories that are responsible for the concentrations observed at a particular receptor. Although receptor models have been used to do source apportionment, they do not fully take into account the chemical reactions (including photochemical reactions) involved in the formation of secondary fine particles. Secondary fine particles are formed from photochemical and other reactions involving precursor gases such as sulfur dioxide (SO₂), oxides of nitrogen (NO_x), ammonia (NH₃) and volatile organic compounds (VOC). The purpose of this research work was to model primary and …

Standard Penetration Test-Based Probabilistic And Deterministic Assessment Of Seismic Soil Liquefaction Potential, K. Onder Cetin, Raymond B. Seed, Armen Der Kiureghian, Kohji Tokimatsu, Leslie F. Harder, Jr., Robert E. Kayen, Robb E. S. Moss

Civil and Environmental Engineering

This paper presents new correlations for assessment of the likelihood of initiation (or “triggering”) of soil liquefaction. These new correlations eliminate several sources of bias intrinsic to previous, similar correlations, and provide greatly reduced overall uncertainty and variance. Key elements in the development of these new correlations are (1) accumulation of a significantly expanded database of field performance case histories; (2) use of improved knowledge and understanding of factors affecting interpretation of standard penetration test data; (3) incorporation of improved understanding of factors affecting site-specific earthquake ground motions (including directivity effects, site-specific response, etc.); (4) use of improved methods for …

Attenuation Of Ultrasonic Waves In Rolled Metals, Liyong Yang, Joseph A. Turner

Nebraska Center for Materials and Nanoscience: Faculty Publications

Scattering of ultrasonic waves in polycrystals with texture is studied in this article. The attenuations of the three wave modes are determined as a function of dimensionless frequency and propagation direction, respectively, for given orientation distribution coefficients (ODCs). The calculation is done in the case of a statistically orthorhombic sample made up of cubic crystallites. The wave propagation and scattering model is formulated by the Dyson equation using an anisotropic Green’s function approach.Within the limits of the first-order smoothing approximation, the Dyson equation is solved in the spatial Fourier transform domain. The results presented are shown to be directional dependent, …

A Template-Based Conceptual Modeling Infrastructure For Simulation Of Physical Security Systems, Ashu Guru, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

Although simulation is one of the most innovative and cost-effective tools for modeling and analyzing a system, simulation studies often fail to provide any useful results. One reason is attributed to the fact that model formulation depends on the skills of the analyst. This paper describes a research to develop a conceptual modeling infrastructure to assist a simulation analyst in specifying components for studying physical security systems. The modeling framework has been programmed as an internet-based web application. Using the application, the successful development and implementation of a physical security simulation model will be aided by a defined scientific methodology …

Flight Physician - December, 2004, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A twenty page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.