Engineering Commons^™

Fast Measurements Of Flow Through Mitral Regurgitant Orifices With Magnetic Resonance Phase Velocity Mapping, Haosen Zhang, Sandra S. Halliburton, Richard D. White, George P. Chatzimavroudis

Chemical & Biomedical Engineering Faculty Publications

Magnetic-resonance (MR) phase velocity mapping (PVM) shows promise in measuring the mitral regurgitant volume. However, in its conventional nonsegmented form, MR-PVM is slow and impractical for clinical use. The aim of this study was to evaluate the accuracy of rapid, segmented k-spaceMR-PVM in quantifying the mitral regurgitant flow through a control volume (CV) method. Two segmented MR-PVM schemes, one with seven (seg-7) and one with nine (seg-9) lines per segment, were evaluated in acrylic regurgitant mitral valve models under steady and pulsatile flow. A nonsegmented (nonseg) MR-PVM acquisition was also performed for reference. The segmented acquisitions were …

Pre-Impact Lower Extremity Posture And Brake Pedal Force Predict Foot And Ankle Forces During An Automobile Collision, Elizabeth C. Hardin, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background: The purpose of this study was to determine how a driver’s foot and ankle forces during a frontal vehicle collision depend on initial lower extremity posture and brake pedal force. Method of Approach: A 2D musculoskeletal model with seven segments and six right-side muscle groups was used. A simulation of a three-second braking task found 3647 sets of muscle activation levels that resulted in stable braking postures with realistic pedal force. These activation patterns were then used in impact simulations where vehicle deceleration was applied and driver movements and foot and ankle forces were simulated. Peak rearfoot ground reaction …

Serviceability-Based Dynamic Loan Rating Of A Lt20 Bridge, P. Siswobusono, S.-E. Chen, S. Jones, D. Callahan, T. Grimes, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

No abstract provided.

2004 Scholars And Artists Bibliography, Michael Schwartz Library, Cleveland State University, Friends Of The Michael Schwartz Library

Scholars and Artists Bibliographies

This bibliography was created for the annual Friends of the Michael Schwartz Library Scholars and Artists Reception, recognizing scholarly and creative achievements of Cleveland State University faculty, staff and emeriti

The Non-Destructive And Nano-Microstructural Characterization Of Thermal-Barrier Coatings, Y. H. Sohn, B. Jayaraj, S. Laxman, B. Franke, J. W. Byeon, Anette M. Karlsson

Mechanical Engineering Faculty Publications

The durability of thermal barrier coatings (TBCs) plays an important role in the service reliability and maintainability of hot-section components in advanced turbine engines for aerospace and utility applications. Photostimulated luminescence spectroscopy (PSLS) and electrochemical impedance spectroscopy (EIS) are being concurrently developed as complimentary nondestructive evaluation (NDE) techniques for quality control and liferemain assessment of TBCs. This paper discusses recent achievements in understanding the residual stress, phase constituents, and electrochemical resistance (or capacitance) of TBC constituents—with an emphasis on the thermally grown oxide. Results from NDE by PSLS and EIS are correlated to the nano- and microstructural development of TBCs.

Multi-D Cfd Modeling Of Free-Piston Stirling Convertor At Nasa Grc, Scott D. Wilson, Rodger W. Dyson, Roy C. Tew, Mounir B. Ibrahim

Mechanical Engineering Faculty Publications

A high efficiency Stirling Radioisotope Generator (SRG) is being developed for possible use in long duration space science missions. NASA s advanced technology goals for next generation Stirling convertors include increasing the Carnot efficiency and percent of Carnot efficiency. To help achieve these goals, a multidimensional Computational Fluid Dynamics (CFD) code is being developed to numerically model unsteady fluid flow and heat transfer phenomena of the oscillating working gas inside Stirling convertors. Simulations of the Stirling convertors for the SRG will help characterize the thermodynamic losses resulting from fluid flow and heat transfer between the working gas and solid walls. …

Sagittal Plane Biomechanics Cannot Injure The Acl During Sidestep Cutting, Scott G. Mclean, Xuemei Huang, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background. Knee joint sagittal plane forces are a proposed mechanism of anterior cruciate ligament injury during sport movements such as sidestep cutting. Ligament force magnitudes for these movements however, remain unknown. The need to examine injury-causing events suggests elucidation via model-based investigations is possible. Using this approach, the current study determined whether sagittal plane knee loading during sidestep cutting could in isolation injure the anterior cruciate ligament.

Methods. Experiments were performed on subject-specific forward dynamic musculoskeletal models, generated from data obtained from 10 male and 10 female athletes. Models were optimized to simulate subject-specific cutting movements. Random perturbations …

Mushy-Zone Rayleigh Number To Describe Macrosegregation And Channel Segregate Formation During Directional Solidification Of Metallic Alloys, Surendra N. Tewari, R. Tiwari, G. Magadi

Chemical & Biomedical Engineering Faculty Publications

A recently defined mushy-zone Rayleigh number (R-aM) that includes side-branching contributions to the mushy-zone permeability has been examined for its correlation with the longitudinal macrosegregation and channel segregate formation. The Rayleigh number shows (1) a strong correlation between the extent of longitudinal macrosegregation and increase in the mushy-zone convection and (2) a good ability to predict the formation of channel segregates during directional solidification.

Power-Stepped Protocol: Enhancing Spatial Utilization In A Clustered Mobile Ad Hoc Network, Chansu Yu, Kang G. Shin, Ben Lee

Electrical and Computer Engineering Faculty Publications

While most previous studies on mobile ad hoc networks (MANETs) rely on the assumption that nodes are randomly distributed in the network coverage area, this assumption is unlikely to hold, as nodes tend to be cluttered around hot spots like the site of an accident or disaster. We refer to this as a clustered layout. Intuitively, a MANET with the clustered layout may suffer from serious performance degradation due to the excessive collisions in congested hot spots and space underutilization of sparse areas. In this paper, we propose a power-controlled network protocol, called the power-stepped protocol (PSP), that maximizes the …

Satellite Attitude Control System Design Using Reaction Wheels, Bhanu Gouda, Brian Fast, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

No abstract provided.

Controller Tuning For Dc Motor Speed Control Using Genetic Algorithms, Saurabh Jain, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

No abstract provided.

Kalman Filtering With Uncertain Noise Covariances, Srikiran Kosanam, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

In this paper the robustness of Kalman filtering against uncertainties in process and measurement noise covariances is discussed. It is shown that a standard Kalman filter may not be robust enough if the process and measurement noise covariances are changed. A new filter is proposed which addresses the uncertainties in process and measurement noise covariances and gives better results than the standard Kalman filter. This new filter is used in simulation to estimate the health parameters of an aircraft gas turbine engine.

Effect Of Gender And Defensive Opponent On The Biomechanics Of Sidestep Cutting, Scott G. Mclean, Susanne W. Lipfert, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Purpose: Anterior cruciate ligament (ACL) injuries often occur in women during cutting maneuvers to evade a defensive player. Gender differences in knee kinematics have been observed, but it is not known to what extent these are linked to abnormal neuromuscular control elsewhere in the kinetic chain. Responses to defense players, which may be gender-dependent, have not been included in previous studies. This study determined the effects of gender and defense player on entire lower extremity biomechanics during sidestepping.

Methods: Eight male and eight female subjects performed sidestep cuts with and without a static defensive opponent while 3D motion and ground …

Synchronous Motor Phase Control By Vector Addition Of Induced Winding Voltages, Daniel J. Simon, Dennis L. Feucht

Electrical and Computer Engineering Faculty Publications

We propose a simple low-cost approach to the winding-sensed control of three-phase synchronous permanent-magnet motors. Our approach results from a straightforward but elegant application of vector-based motor theory. The method therefore does not depend on the differential equations that describe the motor dynamics, and it does not depend on the particular motor parameters. The single method we derive applies to both wye- and delta-configured motors. We vectorially sum the voltage waveforms at the motor terminals in a certain way and use their zero crossings to produce a correctly phased six-step switch sequence. We discuss the implementation for both wye- and …

A Comparison Between Growth Morphology Of "Eutectic" Cells/Dendrites And Single-Phase Cells/Dendrites, Surendra N. Tewari, S. V. Raj, L. E. Locci

Chemical & Biomedical Engineering Faculty Publications

Directionally solidified (DS) intermetallic and ceramicbased eutectic alloys with an in-situ composite microstructure microstructure containing finely distributed, long aspect ratio, fiber, or plate reinforcements are being seriously examined for several advanced aero-propulsion applications. In designing these alloys, additional solutes need to be added to the base eutectic composition in order to improve their high temperature strength, and provide for adequate toughness and resistance to environmental degradation. Solute addition, however, promotes instability at the planar liquid-solid interface resulting in the formation of two-phase eutectic “colonies.”[1–4] Because morphology of eutectic colonies is very similar to the single-phase cells and dendrites, the stability …

Heat Transfer In A Thin Liquid Film In The Presence Of An Electric Field, Rama Subba Reddy Gorla, Jorge E. Gatica, Bahman Ghorashi, Pijarn Ineure, Larry W. Byrd

Chemical & Biomedical Engineering Faculty Publications

Heat transfer enhancement in an evaporating thin liquid film utilizing a electric field under isothermal interfacial condition is presented. A new mathematical model subjected to van der Waals attractive forces, capillary pressure, and an electric field is developed to describe the heat transfer enhancement in the evaporating thin liquid film. The effect of the electrostatic field on the curvature of the thin film, evaporative flux, pressure gradient distribution, heat flux, and heat transfer coefficient in the thin film is presented. The results show that applying an electric field can enhance heat transfer in a thin liquid film significantly. in addition, …

Cavitation Effects On The Stability Of A Submerged Journal Bearing, Jerzy T. Sawicki, T. V. V. L. N. Rao

Mechanical Engineering Faculty Publications

A computational procedure for the mechanism of shear between the liquid sublayer and air cavity in the cavitation zone of a submerged journal bearing is presented here. Using the mass conservation principle, Elrod's universal equation is modified to take into consideration the shear of the air cavity in the cavitation region. Results of steady state and transient response for the submerged journal bearing using the present approach are compared with the universal equation based on the striated flow in the cavitation region. At steady state, the angular extent of cavitation region predicted by the present approach is higher than that …

Foot And Ankle Forces During An Automobile Collision: The Influence Of Muscles, Elizabeth C. Hardin, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Muscles have a potentially important effect on lower extremity injuries during an automobile collision. Computational modeling can be a powerful tool to predict these effects and develop protective interventions. Our purpose was to determine how muscles influence peak foot and ankle forces during an automobile collision. A 2-D bilateral musculoskeletal model was constructed with seven segments. Six muscle groups were included in the right lower extremity, each represented by a Hill muscle model. Vehicle deceleration data were applied as input and the resulting movements were simulated. Three models were evaluated: no muscles (NM), minimal muscle activation at a brake pedal …

Data Smoothing And Interpolation Using Eighth-Order Algebraic Splines, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

A new type of algebraic spline is used to derive a filter for smoothing or interpolating discrete data points. The spline is dependent on control parameters that specify the relative importance of data fitting and the derivatives of the spline. A general spline of arbitrary order is first formulated using matrix equations. We then focus on eighth-order splines because of the continuity of their first three derivatives (desirable for motor and robotics applications). The spline's matrix equations are rewritten to give a recursive filter that can be implemented in real time for lengthy data sequences. The filter is lowpass with …

Effect Of Supplementary Cementitious Materials On The Compressive Strength And Durability Of Short-Term Cured Concrete, H. Toutanji, Norbert Delatte, S. Aggoun, R. Duval, A. Danson

Civil and Environmental Engineering Faculty Publications

This research focuses on studying the effect different supplementary cementitious materials (silica fume, fly ash, slag, and their combinations) on strength and durability of concrete cured for a short period of time—14 days. This work primarily deals with the characteristics of these materials, including strength, durability, and resistance to wet and dry and freeze and thaw environments. Over 16 mixes were made and compared to the control mix. Each of these mixes was either differing in the percentages of the additives or was combinations of two or more additives. All specimens were moist cured for 14 days before testing or …

Collapse Of 2000 Commonwealth Avenue: Punching Shear Case Study, Suzanne King, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

On January 25, 1971, two thirds of a 16-story apartment building collapsed while under construction at 2000 Commonwealth Avenue, Boston, Massachusetts. Four workers died after a failure on the roof instigated a progressive collapse all the way to the basement, where the men were found. Fortunately, the collapse occurred slowly enough for most of the other workers to run to safety. An investigation, conducted by a commission assembled by the Mayor of Boston, painted a picture of a troubled project, with considerable confusion about responsibility for structural safety. The surviving workers’ descriptions of the failure provide a textbook definition of …

On The Microstructural Development In Platinum-Modified Nickel-Aluminide Bond Coats, S. Darzens, Anette M. Karlsson

Mechanical Engineering Faculty Publications

A numerical procedure for simulating the distortions exhibited by a thermally grown oxide (TGO) upon temperature cycling has been adapted to incorporate the microstructure of the bond coat. The focus is on the dual phase β/γ′ microstructure that develops upon oxidation of a system with a Pt-aluminide bond coat. The results reveal that the presence of the γ′-phase next to the TGO reduces its distortion locally, because of the superior high-temperature strength of γ′, relative to β. Conversely, in regions where the β-phase exists adjacent to the TGO, it distorts and the TGO propagates downward, while simultaneously lengthening. These results …

Analysis And Implementation Of A Synchronous Buck Converter Used As An Intermediate Stage Of An Hid Ballast, Sergey V. Vernyuk

ETD Archive

The contribution of this thesis is the analysis of a Synchronous Buck converter, used as the second stage (which controls the current through the lamp, and consequently, the lamp power) in a 3-stage High-Intensity Discharge (HID) ballast. Where previously standard Buck converters were used, this new application of the Synchronous Buck converter to a medium-power lighting ballast improves efficiency by operating the converter in a new, modified critical-conduction mode to achieve soft-switching and improve efficiency significantly. The converter and 2-loop controller will be analyzed in the three HID lamp modes of operation: open circuit, short circuit, and power control mode. …

Undergraduate Summer Research In Structural Engineering, Norbert J. Delatte

Civil and Environmental Engineering Faculty Publications

For the last seven years, a summer Research Experiences for Undergraduates site in structural engineering, funded by the National Science Foundation, has operated at the University of Alabama at Birmingham. During this time, 33 students from 22 colleges and universities have participated in the site. Participants are recruited nationally and have come from as far away as California and Puerto Rico. The program is intended to provide students interested in graduate studies with an introduction to research methods, and to provide students who will not continue their studies past a bachelor of science in civil engineering with a better understanding …

Retention And Viability Characteristics Of Mammalian Cells In An Acoustically Driven Polymer Mesh, Zhaowei Wang, Paul Grabenstetter, Donald L. Feke, Joanne M. Belovich

Chemical & Biomedical Engineering Faculty Publications

A processing approach for the collection and retention of mammalian cells within a high porosity polyester mesh having millimeter-sized pores has been studied. Cell retention occurs via energizing the mesh with a low intensity, resonant acoustic field. The resulting acoustic field induces the interaction of cells with elements of the mesh or with each other and effectively prevents the entrainment of cells in the effluent stream. Experiments involving aqueous suspensions of polystyrene particles were used to provide benchmark data on the performance of the acoustic retention cell. Experiments using mouse hybridoma cells showed that retention densities of over 1.5 × …

A Nonlinear Model For Prediction Of Dynamic Coefficients In A Hydrodynamic Journal Bearing, Jerzy T. Sawicki, T.V.V.L. N. Rao

Mechanical Engineering Faculty Publications

This paper investigates the variation of nonlinear stiffness and damping coefficients in a journal orbit with respect to equilibrium position. The journal orbit is obtained by the combined solution of equations of motion and Reynolds equation. In the linearized dynamic analysis, dynamic pressure is written as a perturbation of static pressure and pressure gradients at equilibrium position. However, in order to obtain nonlinear dynamic coefficients about equilibrium position, the dynamic pressure gradients in the orbit are also written as the first order perturbation of static pressure gradients and higher order pressure gradients for displacement and velocity perturbations. The dynamic coefficients …