Engineering Commons^™

Jet Stability And Noise Computations Using Direct Numerical Simulation, Farouk Owis

Mechanical & Aerospace Engineering Theses & Dissertations

The computations of axisymmetric jet noise with symmetric disturbances are investigated using the direct numerical simulation of the unsteady compressible Navier-Stokes equations. High order accurate numerical schemes are employed for the solution of the governing equations. The investigation shows that MacCormack schemes with operator splitting and minimum dispersion error can be used to predict noise radiated from subsonic and supersonic jets with low and high Reynolds numbers. In addition, different kinds of nonreflecting boundary conditions are used at the inflow and outflow boundaries. These boundary conditions include characteristic boundary conditions, buffer domain technique and perfectly matching layer method. The results …

Exploring Participation Processes For Technology Development: Case Studies Of Biotechnology Research And Development Projects In Thailand, Omjai Yuktavetya

Engineering Management & Systems Engineering Theses & Dissertations

There is increased awareness in the organizational and management literature that participation can make contributions in technology development. One of the problems in developing biotechnology in Thailand is that only a small portion of publicly funded research and development projects directly result in commercial success. Among the reasons cited (TDRI 1992a) is a lack of collaboration between various stakeholders; therefore, an effective technology policy to support their participation is needed. This research explores current participation processes in biotechnology research and development projects in Thailand in which there were different perspectives among various stakeholders. The quantitative and qualitative methodologies developed here …

Large Amplitude Pitching Of Supermaneuver Delta Wings Including Flow Control, Yahia A. Abdelhamid

Mechanical & Aerospace Engineering Theses & Dissertations

The unsteady, three-dimensional Navier-Stokes equations are solved to simulate and study the aerodynamic response of a delta wing undergoing large amplitude pitching motion up to 90° angle of attack. The primary model under consideration consists of a 76° swept, sharp-edged delta wing of zero thickness, initially at zero angle of attack. The freestream Mach number and Reynolds number are 0.3 and 0.45 × 106, respectively. The governing equations are solved time-accurately using the implicit, upwind, Roe flux-difference splitting, finite-volume scheme. Both laminar and turbulent flow solutions are investigated. In the laminar flow solutions, validation of the computational results is carried …

Two Approaches To Critical Path Scheduling For A Heterogeneous Environment, Guangxia Liu

Computer Science Theses & Dissertations

Advances in computing and networking technologies are making large scale distributed heterogeneous computing a reality. Multi-Disciplinary Optimization (MDO) is a class of applications that is being addressed under this paradigm. It consists of multiple heterogeneous modules interacting with each other to solve an overall design problem. An efficient implementation of such an application requires scheduling heterogeneous modules (with different computing and disk 1/0 requirements) on a heterogeneous set of resources (with different CPU, memory, disk IO specifications).

Given a set of tasks and a set of resources, an optimal schedule of the tasks on the resources is very hard to …

The Effects Of Offshore Mining Of Beach Quality Sediments On Nearshore Wave Climate, Frank R. Lonza

Civil & Environmental Engineering Theses & Dissertations

Coastal communities rely on the beaches to attract tourism, but these sources of revenue require maintenance, such as beach nourishment. In an effort to maintain these beaches without causing any detrimental results, research is conducted to determine what effects, if any, exist when mining for sand in offshore areas.

The U.S. Government is permitting the search for beach quality sands offshore but is also ensuring that such mining will not have adverse results to the nearshore wave climate. This study was conducted using a coarse grid bathymetric map to calibrate a numerical model developed by the Danish Hydraulic Institute (DHI). …

Preparation And Surface Studies Of Negative Electron Affinity Semiconductors Photocathodes, Khaled A. Elamrawi

Electrical & Computer Engineering Theses & Dissertations

Fabrication of high quantum efficiency, long lifetime negative electron affinity photocathodes is important for applications such as photomultipliers, image intensifiers, electron beam lithography, electron microscopy, and polarized electron sources. The surface cleanliness of the III-V semiconductor photocathode is crucial in obtaining high photosensitivity.

GaAs(100) and InP(100) photocathodes are prepared by atomic hydrogen cleaning. The cleaning effect on the photocathode performance is discussed. The surface degradation mechanisms which reduce the photocathode lifetime are presented. The photocathode surface cleanliness, structure, and morphology are studied using reflection high-energy electron diffraction (RHEED).

Quantum efficiencies of ∼14% and 8% are obtained for GaAs and InP, …

Stratal Architecture In A Prograding Shoreface Deposit, Eastern Shore, Va: Relationship To Grain Size, Permeability, And Facies Distribution, Andrew C. Miller

OES Theses and Dissertations

A fundamental concern of the stratigrapher is to develop predictive models of stratigraphic organization. In sedimentology one of the most significant problems that has yet to be resolved is the fact that there is a lack of quantitative information regarding the relationship between geometry of beds, thickness of beds, grain size and sedimentary structures in sandy environments, especially shallow marine deposits. Scientists have also realized the need to correlate quantitative permeability to sedimentary structures and scales of stratigraphic organization. The purpose of the study is to investigate the scales of stratigraphic organization that control the variation of grain size and …

Direct Current Glow Discharges In Atmospheric Air, Robert H. Stark, Karl H. Schoenbach

Bioelectrics Publications

Direct current glow discharges have been operated in atmospheric air by using 100 μm microhollow cathode discharges as plasma cathodes. The glow discharges were operated at currents of up to 22 mA, corresponding to current densities of 3.8 A/cm² and at average electric fields of 1.2 kV/cm. Electron densities in the glow are in the range from 10¹² to 10¹³  cm⁻³. Varying the current of the microhollow cathode discharge allows us to control the current in the atmospheric pressure glow discharge. Large volume atmospheric pressure air plasmas can be generated by operating microhollow cathode discharges …

Computation Of Flame Base Height Of A Turbulent Diffusion Flame Resulting From A Methane Jet, A. S. Kheireddine, S. K. Chaturvedi, T. O. Mohieldin

Mechanical & Aerospace Engineering Faculty Publications

This work summarizes numerical results for a diffusion flame formed from a cylindrical tube fuel injector, issuing a gaseous methane jet vertically in a quiescent atmosphere. The primary objective is to predict the flame base height and other flame characteristics as a function of the fuel jet velocity. A finite volume scheme is used to discretize the time-averaged Navier-Stokes equations for the reacting flow resulting from the turbulent fuel jet motion. The turbulent stresses, and heat and mass fluxes are computed from a Reynolds stress turbulence model. A chemical kinetics model involving two-step chemistry is employed for the oxidation of …

Time-Resolved Reflection High-Energy Electron Diffraction Study Of The Ge(111)-C(2×8)-(1×1) Phase Transition, Xinglin Zeng, Bo Lin, Ibrahim El-Kholy, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The dynamics of the Ge(111)-c(2×8)-(1×1) phase transition is investigated by 100-ps time-resolved reflection high-energy electron diffraction. A laser pulse heats the surface while a synchronized electron pulse is used to obtain the surface diffraction pattern. Slow heating shows that the adatoms in Ge(111)-c(2×8) start to disorder at ∼510 K and are converted to a disordered adatom arrangement at 573 K. For heating with 100-ps laser pulses, the Ge(111)-c(2×8) reconstructed adatom arrangement starts to disorder at 584±16K, well above the onset temperature of ∼510 K for the disordering of Ge(111)-c(2×8) observed for slow …

Elasto-Plastic Responses Of Buried Pipeline Systems Under Wave Propagation, Yuean-Chen Lau

Civil & Environmental Engineering Theses & Dissertations

The purpose of this research is to study the elastic and inelastic behavior of buried pipeline system under arbitrary seismic wave propagation. Both continuous and segmented pipes with joints and junctions are included. The surrounding soil is simulated by a series of elasto-plastic springs uniformly distributed longitudinally and laterally along the pipes. To the joints, elasto-plastic longitudinal springs and bilinear rotational springs are adopted. It is assumed that the pipes remain linearly elastic. The effects of soil liquefaction and fault movement are not considered.

Since the dynamic effect has been found to be negligible, a quasi-static analysis is adopted in …

Computational Modeling Of Airborne Noise Demonstrated Via Benchmarks, Supersonic Jet, And Railway Barrier, Moumen Idres

Mechanical & Aerospace Engineering Theses & Dissertations

In the last several years, there has been a growing demand for mobility to cope with the increasing population. All kinds of transportation have responded to this demand by expanding their networks and introducing new ideas. Rail transportation introduced the idea of high-speed trains and air transportation introduced the idea of high-speed civil transport (HSCT). In this expanding world, the noise legislation is felt to inhibit these plans. Accurate computational methods for noise prediction are in great demand.

In the current research, two computational methods are developed to predict noise propagation in air. The first method is based on the …

Continuous Adjoint Sensitivity Analysis For Aerodynamic And Acoustic Optimization, Kaveh Ghayour

Mechanical & Aerospace Engineering Theses & Dissertations

A gradient-based shape optimization methodology based on continuous adjoint sensitivities has been developed for two-dimensional steady Euler equations on unstructured meshes and the unsteady transonic small disturbance equation. The continuous adjoint sensitivities of the Helmholtz equation for acoustic applications have also been derived and discussed.

The highlights of the developments for the steady two-dimensional Euler equations are the generalization of the airfoil surface boundary condition of the adjoint system to allow a proper closure of the Lagrangian functional associated with a general cost functional and the results for an inverse problem with density as the prescribed target. Furthermore, it has …

A Qfd Decision Model For Selecting Service, Teaching, And Research Opportunities, Paul Kauffmann, Abel Fernandez, Charles Keating

Engineering Management & Systems Engineering Faculty Publications

New faculty are confronted with a barrage of information reiterating the importance of performance in the "big three" areas: teaching, service, and research / publications. From the provost to the department head, an untenured faculty member faces strong and sometimes conflicting pressures to become involved in activities ranging from committee assignments to participation in department or university research programs. Often these opportunities come with little guidance, advice, or obvious linkage to long term success in the three pillar areas and ultimately tenure. New faculty are confronted with a complex decision problem for which there is unstructured information available to develop …

Réalisation De Couches Minces De Cualse² Par Recuit De Feuilllets Superposés Cu/Al/Se/Al…, Étude De Conditions De Dépôt, C.O. El Moctar, S. Marsillac, J. C. Bernede, A. Conan, K. Benchouk, A. Khelil

Electrical & Computer Engineering Faculty Publications

Thin layers of Cu/Al/Se/Al/Cu/Al/Se/…/Al/Se sequentially deposited have been annealed half an hour at 855 K. CuAlSe₂ thin films crystallized in the chalcopyrite structure are obtained. The films being contaminated by oxygen, the experimental deposition conditions of the aluminum layer have been improved in order to decrease the atomic concentration of oxygen below 5 at%. Such results can be obtained in vacuum of 10^-4 Pa, when the aluminum deposition rate is 1 nm/s and when the layer is immediately covered after deposition. Films obtained in such a way are nearly stoichiometric with lattice parameters in accordance with the expected …

Direct Current High-Pressure Glow Discharges, Robert H. Stark, Karl H. Schoenbach

Bioelectrics Publications

Stabilization and control of a high-pressure glow discharge by means of a microhollow cathode discharge has been demonstrated. The microhollow cathode discharge, which is sustained between two closely spaced electrodes with openings of approximately 100 μm diam, serves as plasma cathode for the high-pressure glow. Small variations in the microhollow cathode discharge voltage generate large variations in the microhollow cathode discharge current and consequently in the glow discharge current. In this mode of operation the electrical characteristic of this system of coupled discharges resembles that of a vacuum triode. Using the microhollow cathode discharge as plasma cathode it was possible …

Smart Objects, Dumb Archives: A User-Centric, Layered Digital Library Framework, Kurt Maly, Michael L. Nelson, Mohammad Zubair

Computer Science Faculty Publications

Discusses digital libraries, interoperability, and interfaces to access them, and proposes one universal protocol for communication for simple archives based on the hypertext transfer protocol (http). Describes the creation of a special class of digital objects called buckets, archives based on a NASA collection, and a set of digital library services. (Author/LRW)

A Digital Library For The National Advisory Committee For Aeronautics, Michael L. Nelson

Computer Science Faculty Publications

We describe the digital library (DL) for the National Advisory Committee for Aeronautics (NACA), the NACA Technical Report Server (NACATRS). The predecessor organization for the National Aeronautics and Space Administration (NASA), NACA existed from 1915 until 1958. The primary manifestation of NACA's research was the NACA report series. We describe the process of converting this collection of reports to digital format and making it available on the World Wide Web (WWW) and is a node in the NASA Technical Report Server (NTRS). We describe the current state of the project, the resulting DL technology developed from the project, and the …

Design And Construction Of A Mobile Laboratory For Distance Learning In Engineering Technology, Alok K. Verma

Engineering Technology Faculty Publications

The design and construction of a mobile laboratory to be used in conjunction with the televised program in Mechanical Engineering Technology Program at Old Dominion University is discussed. The aim of this program is to offer educational opportunities to individuals currently employed with an associate degree. The merit of the concept lies in the fact that it offers a cost effective way to provide a laboratory for multiple sites. Currently, the concept is being tested for two instructional areas, such as fluid mechanics and automatic controls.

Compute As Fast As The Engineers Can Think! Utrafast Computing Team Final Report, Robert T. Biedron, P. Mehrotra, Michael L. Nelson, M. L. Preston, J. J. Rehder, J. L. Rogersm, D. H. Rudy, J. Sobieski, O. O. Storaasli

Computer Science Faculty Publications

This report documents findings and recommendations by the Ultrafast Computing Team (UCT). In the period 10-12/98, UCT reviewed design case scenarios for a supersonic transport and a reusable launch vehicle to derive computing requirements necessary for support of a design process with efficiency so radically improved that human thought rather than the computer paces the process. Assessment of the present computing capability against the above requirements indicated a need for further improvement in computing speed by several orders of magnitude to reduce time to solution from tens of hours to seconds in major applications. Evaluation of the trends in computer …

Setpoint Tracking Predictive Control In Chemical Processes Based On System Identification, Sinchai Chinvorarat

Mechanical & Aerospace Engineering Theses & Dissertations

A Kraft recovery boiler in a pulp-paper mill provides a means for recovery of the heat energy in spent liquor and recovery of inorganic chemicals while controlling emissions. These processes are carried out in a combined chemical recovery unit and steam boiler that is fired with concentrated black liquor and which produces molten smelt. Since the recovery boiler is considered to be an essential part of the pulp-paper mill in terms of energy resources, the performance of the recovery boiler has to be controlled to achieve the highest efficiency under unexpected disturbances.

This dissertation presents a new approach for combining …

Surface Resistance Measurements Of Superconducting Niobium Samples With A Triaxial Cavity, Paul Martin Boccard

Physics Theses & Dissertations

This experimental study has revealed and investigated many of the physical issues that affect accurate measurement of the surface resistance for small samples consisting of superconducting niobium films on copper substrates. It is believed that this work provides the groundwork for future research directed towards solving this important problem. Accurate measurement of surface resistance for such samples is needed to allow the rapid evaluation and optimization of the deposition parameters necessary for manufacturing low-loss superconducting niobium films.

A superconducting niobium triaxial cavity was investigated to determine its suitability for measuring the residual surface resistance of copper samples that were sputter-coated …

Studies Related To The Design Of A Magnetic Suspension And Balance System For An Ultra-High Reynolds Number Flow Facility, Oscar Magno Michael Gomeiz

Mechanical & Aerospace Engineering Theses & Dissertations

The basic design principles for a magnetic suspension and balance system applied to the test section of an ultra-high Reynolds number facility are defined. The design of the cross-sectional area to be used in the test section is analyzed. The parameters of the permanent magnet to be used in the model inside the test section are investigated. The testing of magnetic fields at the center of a test pipe and validation of data by computer finite element analysis is described with the purpose of finding common results. The performance of the magnet configuration is evaluated with relation to the magnetic …

Efficient Dynamic Unstructured Methods And Applications For Transonic Flows And Hypersonic Stage Separation, Xiaobing Luo

Mechanical & Aerospace Engineering Theses & Dissertations

Relative-moving boundary problems have a wide variety of applications. They appear in staging during a launch process, store separation from a military aircraft, rotor-stator interaction in turbomachinery, and dynamic aeroelasticity.

The dynamic unstructured technology (DUT) is potentially a strong approach to simulate unsteady flows around relative-moving bodies, by solving time-dependent governing equations. The dual-time stepping scheme is implemented to improve its efficiency while not compromising the accuracy of solutions. The validation of the implicit scheme is performed on a pitching NACA0012 airfoil and a rectangular wing with low reduced frequencies in transonic flows. All the matured accelerating techniques, including the …

Multidisciplinary Sensitivity Analysis And Design Optimization Of Flexible Wings Using The Euler Equations On Unstructured Grids, Arunkumar Satyanarayana

Mechanical & Aerospace Engineering Theses & Dissertations

Aeroelasticity is a classical discipline. However, even with recent advancement in computational technology, it still remains a challenging discipline. This is particularly true when aeroelasticity problems are solved in a loosely coupled manner. The advantage of a loosely coupled scheme is that the legacy codes of computational fluid dynamics (CFD) and computational structural mechanics (CSM) can be preserved and used as independent modules in solving the desired aeroelasticity problems. In such a scheme, maintaining proper data transfer (load transfer and deformation tracking between CFD and CSM codes) is crucial in ensuring successful coupled solutions. This can be a challenging task …