Engineering Commons^™

Instability In Self-Pulsation In Laser Diodes And Its Effect On All-Optical Synchonization, Jonathan Hyland, Gerald Farrell

Articles

The effect of short- and long-term frequency instability in self pulsation on all-optical synchronization using a twin-section laser diode is experimentally investigated. Short-term frequency instability broadens the unlocked full width at half maximum (FWHM) of the fundamental of the rf spectrum of the self-pulsating laser diode. We show experimentally that the value of the unlocked FWHM, and thus the level of short-term instability, has a direct effect on the optical power required to maintain synchronization. A novel means of reducing the FWHM is presented based on a reflective transmission line stub connected to the absorber of the twin-section self-pulsating laser …

Optical-Fiber Preamplifiers For Ladar Detection And Associated Measurements For Improving The Signal-To-Noise Ratio, Michael S. Salisbury, Paul F. Mcmanamon, Bradley D. Duncan

Electro-Optics and Photonics Faculty Publications

In an effort to increase achievable postdetection signal-tonoise ratios (SNRs) of continuous-wave, 1-gm all-solid-state ladar systems, a prototype rare-earth-doped optical-fiber amplifier has been included in the optical return signal path of both a heterodyne and a directdetection ladar system. We provide numerical predictions for SNR increases according to our previously developed theory. We also detail our experimental efforts and provide the results of SNR measurements for four distinct cases: direct ladar detection with and without a fiber amplifier, and heterodyne ladar detection with and without a fiber amplifier. Experimentally measured increases in SNRs for ladar systems incorporating an optical-fiber amplifier …

In Vitro Activities Of 2,2'-Bipyridyl Analogs Against Mycobacterium Leprae, Arvind Madhav Dhople, Maria Antonia Ibáñez, Anita A. Dhople

Biomedical Engineering and Sciences Faculty Publications

In vitro susceptibility of Mycobacterium leprae to two bipyridyl analogs was studied by using two biochemical parameters to measure the metabolic activity of the organism. VUF-8514 at 0.16 μg/ml, but not VUF-8842, completely inhibited the metabolic activity of M. leprae, and the action was bactericidal. When compared to rifampin (MIC 0.3 μg/ml), VUF-8514 was equally bactericidal against M. leprae.

An Overview Of Flexible Ac Transmission Systems, P. Asare, T. Diez, A. Galli, E. O'Neill-Carillo, J. Robertson, R. Zhao

Department of Electrical and Computer Engineering Technical Reports

FACTS or "flexible AC transmission systems" is a term that has been suggested for the use of solid state devices to control bulk power flow in transmission systems. The Electric Power Research Institute supported this idea, and many researchers have invested efforts on the value and potential of FACTS. At this time, it appears that the main value of FACTS lies in improving transmission capability; increasing the flexibility of power flow control (e.g., for wheeling or for economic dispatch); for controlling voltage (and var flow); and possibly additional advantages in lower voltage systems (e.g., distribution systems). This report is an …

A Computer Allocation Algorithm For Space Problem, Hesham Abdel Aziz Ibrahim

Archived Theses and Dissertations

No abstract provided.

Resilient And Residual Properties Of Egyptian Asphalt Concrete, Medhat Habil Shehata

Archived Theses and Dissertations

No abstract provided.

Vortex Lattice Symmetry And Electronic Structure In Yba₂Cu₃O₇, Bernhard Keimer, Wan Y. Shih, Ross W. Erwin, Jeffrey W. Lynn, Fatih Dogan, Ilhan A. Aksay

Materials Science and Engineering Faculty Research & Creative Works

We report a small angle neutron scattering study of the vortex lattice in YBa₂Cu₃O₇ in magnetic fields of 0.5≤H≤5 T applied along and close to the c axis. Over the entire field range, the vortices form an oblique lattice with two nearly equal lattice constants and an angle of 73°between primitive vectors. Numerical calculations suggest that variations of the superconducting order parameter near the vortex core are important in stabilizing this structure. An analysis that accounts for the fourfold symmetry of the vortex core qualitatively explains both the symmetry and the orientation of the observed …

Flight Control Design Using Mixed H2/Μ Optimization, Douglas D. Decker

Theses and Dissertations

This thesis examines the use of the mixed H2-Microns optimal control synthesis method in the design of a flight control system for the lateral-directional axes of the F-16 Variable Stability In-Flight Simulator Test Aircraft (VISTA). The method is designed to minimize the H2 norm (two-norm) for a given value of microns. This should provide adequate noise and disturbance rejection while maintaining robustness against several types of uncertainties in the system. This thesis finds that, for this problem, the two-norm is not an accurate representation of the outputs of interest. When the two-norm is broken up into its constituent parts an …

Viscoplastic Characterization And Fatigue Modeling Of Titanium Based Metal Matrix Composites, Mark A. Foringer

Theses and Dissertations

Viscoplastic characterization and fatigue modeling of titanium-based metal matrix composites was accomplished by combining a unified viscoplastic theory, a nonlinear micromechanics model, and a linear damage accumulation model. First. Ti 15-3 was characterized using the Bodner-Partom viscoplastic theory. A micromechanics model was then employed in a linear damage accumulation fatigue model to predict the fatigue behavior of titanium based composites. The viscoplastic behavior predictions of the micromechanics model were used to eliminate separately defined time dependent terms in the fatigue model. Also, a new linear damage accumulation model was developed from the fatigue behavior of the composite constituents. Finally, it …

Applications Of ℓ1 And Mixed H2/ℓ1 Optimization, Mark S. Spillman

Theses and Dissertations

This thesis explores the use of ℓ₁ and mixed H2/ℓ1 optimization methods to design flight control systems. ℓ₁ optimization is used to handle tracking issues in the design of digital compensators. Control deflection and rate limitations, overshoot and undershoot limitations and steady-state error requirements are discussed. Model-matching techniques which produce acceptable tracking results with lower order controllers are also examined. New numerical methods for continuous H2/L1 and discrete H2/ℓ1 optimization are presented. These methods are used to design an aircraft controller in continuous and discrete time and the results are compared.

Sorption Of Chlorinated Organic Compounds By Sedimentary Rocks, Paul M. Mcginley, S. Kesaraju, Ronald D. Gruzesky

KWRRI Research Reports

The sorption of dichlorobenzene and trichlorobenzene on carbonate and shale rocks collected in Kentucky demonstrate that rock organic matter content is a good indicator of sorptive reactivity in rock systems. Although this is similar to soil systems, significant differences between sorption in rock and soil systems exist. Sorption isotherms on these rocks are nonlinear and sorption can be an order of magnitude higher than predicted using correlations from soils and their organic matter content. This sorption reaction could lead to significant concentration tailing during contaminant cleanup. Experimental elution of trichloroethylene from rock filled columns verified that cleanup times might be …

A Contactless Method For Measuring The Bulk Resistance Of Ii-Vi Compound Semiconductors, Edward D. Wheeler, Jack L. Boone, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

A radio frequency measurement technique for measuring the bulk resistivity of II-VI compound semiconductors is described. Wafers of n-type CdS are used to demonstrate the technique. An equivalent circuit model is introduced which predicts a frequency dependence for the CdS wafer impedance which agrees well with the experiment. The model assumes a broad distribution of relaxation times associated with the polarization. The radio frequency method gives values for the resistivity within 15% of four point probe measurements for the lower resistivity wafers, and within 5% for the higher resistivity wafers.

The Fat-Pyramid And Universal Parallel Computation Independent Of Wire Delay, Ronald I. Greenberg

Computer Science: Faculty Publications and Other Works

This paper shows that a fat-pyramid of area Θ(A) requires only O(log A) slowdown to simulate any competing network of area A under very general conditions. The result holds regardless of the processor size (amount of attached memory) and number of processors in the competing networks as long as the limitation on total area is met. Furthermore, the result is valid regardless of the relationship between wire length and wire delay. We especially focus on elimination of the common simplifying assumption that unit time suffices to traverse a wire regardless of its length, since the assumption becomes more and more …

The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge

Theses and Dissertations

This thesis encompassed the design, development, and application of a low-speed, low-force data acquisition system for the AFIT 5-ft Wind Tunnel. The new data acquisition system was designed and developed to measure approximately 0.045 N (about 0.01 lb_f) at nearly 64.4 km/h (40 mph). Verification of the capability was obtained through testing of a cylindrical model. As part of a technology transition program with Wright Laboratory, this new system was used to investigate bicycle front fork blade spacing in order to determine the optimal spacing for minimum drag. As for the minimum drag of a bicycle with an …

A New Drag Measurement System For Wind Tunnel Testing Of The Racing Bicycle And Rider To Determine A Low Drag Configuration, Brian A. Parker

Theses and Dissertations

This study investigated the application of splitter plate effects to reduce the aerodynamic drag of the racing bicycle and rider system. A sensitive, low-force, beam-type, single-component balance was developed to provide drag measurements accurate to within 0.053 N (0.012 lb_f). The performance of the new system was verified by comparing the measured drag on a three-dimensioaal, right-circular cylinder model, 0.127 m (5.0 in) in diameter and 0.610 m (24 in) long, with the results from a commercial balance and a other similar data. The bicycle and rider model consisted of a full-scale mannequin comprising only the hips, legs …

Total Ionizing Dose Effects In Mosfet Devices At 77 K, Kevin J. Daul

Theses and Dissertations

Total ionizing dose effects on thermal oxide and reoxidized nitrided oxide (RNO) MOSFET devices at 77 K were studied. The MOSFETs were immersed in liquid nitrogen and irradiated, using a ⁶⁰Co source, up to 1 Mrad(Si) at a dose rate of 107 rads(Si)-sec. Drain current-gate voltage characteristics were obtained and used to determine threshold voltage and transconductance. At 77 K the subthreshold slopes indicated no observed buildup of interface states in any of the transistors. Furthermore, all transistors experienced very little change in the transconductance. Typical negative shifts in threshold voltage as dose increased were observed in all of …

An Evolutionary Approach To Allocating Tasks In Hard Real-Time Distributed Systems, Christian Lang

Masters Theses

In real-time systems, correctness not only depends on the result of the computation but also on the time at which this result is available. The violation of timing constraints in hard real-time systems can be critical to human life or environment. Therefore, the scheduling algorithm for distributed systems has to allocate tasks to processing nodes so that no timing constraints can be violated. In addition to timing constraints, tasks have precedence and fault-tolerance constraints.

Static scheduling allocates tasks to processing nodes before the tasks are executed. Static scheduling problems are known to be NP-hard [4]. Therefore, heuristic techniques are necessary …

An Investigation And Improvement Of Electrorheological (Er) Fluid Technology, Adil F. Dalal

Masters Theses

The purpose of this research was to investigate and overcome the limitations of Electrorheological (ER) fluids and to introduce this advanced technology at WMU. Electrorheological (ER) Fluids are a special class of fluids, which exhibit a reversible, infinitely variable phase transition from a liquid to a solid/semi-plastic state, in the presence of an electric field.

ER fluids can provide a unique solution to the problems of vibration isolation of systems. The applications are currently limited due to the high voltage requirements, electric power related heating and limited research into wear/abrasive characteristics of ER fluids.

A specially designed and constructed "electro-viscosimeter" …

Investigation Of Boundary Layer And Performance Effects Of Transpiration Cooling Through A Porous Plate In A Rocket Nozzle, David N. Keener

Theses and Dissertations

This study used a range of low blowing ratios with air through an area of porous material in a Mach 2.0 nozzle to quantity the change in boundary layer thickness as a function of blowing ratio. Also, exit and wall Mach number profiles at each blowing ratio were collected to characterize performance losses as a result of blowing. Performance in terms of specific impulse was also studied. As expected, the boundary layer thickness increased and nozzle performance in terms of exit Mach number decreased with increasing blowing ratio.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]_4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.

Next Generation Real-Time Systems: Investigating The Potential Of Partial-Solution Tasks, Robert E. J. Caley

Theses and Dissertations

While the cyclic executive and fixed-priority scheduling strategies have been sufficient to handle traditional real- time requirements. they are insufficient for dealing with the complexities of next-generation real-time systems. New methods of intelligent control must be developed for guaranteeing on-time task completion for real-time systems that are faced with unpredictable and dynamically changing requirements. Implementing real-time processes as partial-solution tasks is one technique that may be beneficial. This type of task. when combined with intelligent control, has the potential for increasing pre-runtime schedulability, system maintainability. and runtime robustness. This research investigates the benefits of partial-solution tasks by experimentally measuring the …

Improving The Performance Of Spiral Antennas By Using Passive Scatterers, Joseph S. Zaren

Theses and Dissertations

The purpose of this study was to explore the viability of improving the performance of cavity-backed antennas. Traditionally antenna cavities are filled with electromagnetic absorber to mitigate interference effects that would otherwise cause the antenna radiation pattern to vary widely at different frequencies. The approach used in this research was to replace the absorber with dielectric slabs, some of which contained arrays of dipoles. These dipole arrays were modeled as frequency selective surfaces using two periodic moment method based - computer programs and one transmission line program. A systematic study was performed that identified the effect of changing the dipole …

Frame Selection Performance Limits For Statistical Image Reconstruction Of Adaptive Optics Compensated Images, Stephen D. Ford

Theses and Dissertations

The U.S. Air Force uses adaptive optics systems to collect images of extended objects beyond the atmosphere. These systems use wavefront sensors and deformable mirrors to compensate for atmospheric turbulence induced aberrations. Adaptive optics greatly enhance image quality; however, wavefront aberrations are not completely eliminated. Therefore, post-detection processing techniques are employed to further improve the compensated images. Typically, many short exposure images are collected, recentered to compensate for tilt, and then averaged to overcome randomness in the images and improve signal-to-noise ratio. Experience shows that some short exposure images in a data set are better than others. Frame selection exploits …

Development Of Guidelines And Performance For Asphalt Concrete Containing Recycled Rubber, Kamyar C. Mahboub, Donn E. Hancher

Kentucky Transportation Center Research Report

The primary objective of this study was to investigate the feasibility of implementation of the crumb rubber technology in Kentucky. The impetus for this study was provided by the Intermodal Surface Transportation Efficiency Act of 1991 (lSTEA).

This study included an overview of existing literature on the subject from an implementation point of view for Kentucky's conditions. Upon completion of this phase of the study, guidelines were developed by the KTC research team and were submitted to the Transportation Cabinet for field implementation of the crumb rubber modifier (CRM) technology in Kentucky. From the ease of implementation point of view, …

Evaluation Of Change Interval Treatments For Traffic Signals At High-Speed Intersections, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

A large number of traffic accidents at signalized intersections on high-speed roadways occur during or just after the change interval. The green extension system (GES) has been used extensively in Kentucky as a method of alleviating the problem related to the dilemma zone. An alternate method of handling this problem involves warning drivers that the signal indication is about to change from green to red using advance warning flashers (AWF). The objectives of this study were: 1) to evaluate the alternative methods (GES or AWF) which can be used to lessen the problem associated with the dilemma zone which occurs …

Distributed Interactive Simulation Virtual Cassette Recorder (Dis Vcr): A Datalogger With Variable Speed Replay, Jonathan L. Fortner

Theses and Dissertations

The overall objective of the Distributed Interactive Simulation Virtual Cassette Recorder (DIS VCR) is to add a flexible replay capability to any DIS environment and specifically to the Remote Debriefing Tool (RDT). The DIS VCR's abilities include selective filtering of incoming DIS Protocol Data Units (PDUs), variable-speed replays, ability to pause, fast-forward, rewind, efficient data storage and retrieval, and an interface that simplifies the execution of those functions. The thesis includes a DIS VCR-compatible design for concurrent replay of audio extracted from signal PDUs and an extension to the replay design that supports unmodifiable rendering or receiving applications. For variable-speed …

An Exploration Of Technology Transfer Control: A Case Study Of Wright Laboratory, William K. West

Theses and Dissertations

Federal laboratories, system product centers, and military logistics centers are being challenged to leverage national investments in technology beyond their traditional customer base--technology transfer. Participation in domestic technology transfer is growing at an astounding rate. Additionally, the federal government has invested and continues to invest billions of dollars into active defense conversion, dual-use technology, and technology transfer. The objective of this research is to explore how one government laboratory controls its technology transfer process, in both the near and long terms. This research examines the motives for participating in technology transfer. The researcher presents several of the processes that are …

The Effects Of Transverse Vibration On The Performance Of An Axial Groove Wick Heat Pipe, Kenneth A. Carpenter

Theses and Dissertations

An experimental investigation was performed to determine the effects of transverse vibrations on the performance of an ammonia-aluminum axial groove wick heat pipe. Theoretical calculations predicted a performance degradation due to the working fluid being shaken out of the upper capillary grooves. A benchtop shaker was used to apply transverse, sinusoidal vibrations of 30, 35, and 40 Hertz, corresponding to peak acceleration amplitudes of 1.84g, 2.50g, and 3.27g, respectively. Maximum heat throughput, Q sub max, of the vibrating heat pipe was measured. A comparison of these values and static Q sub max values indicated a degradation in heat pipe performance. …

Experimental Investigation Of The Effects Of Relative Physical Orientation Between Evaporator And Condenser For A Loop Heat Pipe, Brad R. Thompson

Theses and Dissertations

This research examined the effects on performance of varying angular orientation and height differences between evaporator and condenser for a loop heat pipe. Performance was defined as the difference in temperature between evaporator and condenser (DELTA T). The pipe was evaluated at varying input power (Qin) for: varying evaporator and condenser angles, different coolant temperatures, and varying relative height differences. All analysis included only steady state operation. The performance was influenced by condenser angles, with an optimal condenser angle for best performance being +45 degrees from horizontal. Additionally, the evaporator angles were found to influence performance only at low Qin …

Compressible Turbulence Measurements In A Supersonic Flow With Adverse Pressure Gradient, Jon W. Dotter

Theses and Dissertations

Mean flow and compressible turbulence measurements have been obtained upstream and within a shock boundary interaction and a compression ramp in Mach 3 flow. Compressible turbulence models have met with little success in the accurate prediction of high-speed flows involving complicated shock boundary interactions and adverse pressure gradients because of a crucial lack of experimental data. Data were collected using conventional Pitot and cone static probes, single overheat cross-wire anemometry, multiple overheat cross-wire anemometry, and flow visualization techniques. Direct measurements of the total Reynolds shear stress were obtained using a turbulence transformation. Results indicate that compressibility effects, as evidenced by …