Engineering Commons^™

Agglomarate Formation During Drying Of Fine Powders, Alok Maskara

Nuclear Engineering ETDs

The effect of capillary pressure, solubility, and surface chemistry on agglomeration of silica and titania particles during drying was studied. Three batches of silica particles with diameter between 15 and 500 nm as well as titania particles with nominal diameter of 30 nm were used. Drying rate was varied by using both tray drying and spray drying. Aprotic solvents ranging in surface tension from 18 dynes/cm (hexane) to 72 dynes/cm (water), and mixtures of water/propanol and water/butanol ranging in surface tension from 35 dynes/cm to 72 dynes/cm, were used to vary the surface tension of the solvent. Water between pH …

Impact Of Nuclear Rocket Engine Design On Control Strategies, John A. Lambright

Nuclear Engineering ETDs

In a nuclear thermal rocket engine, the propellant gas can be varied independent of the peak chamber temperature. Startup and shutdown times can be varied over a wide range due to this uncoupling of the energy source from the working fluid. Therefore, in the early stages of nuclear rocket engine development. a study of the impact of the engine design on control strategies and systems was conducted. In order to define what is required in terms of engine thrusting times. this study focused on the thrust requirements for a Reusable Orbital Transfer Vehicle (R0TV).

Three nuclear rocket designs were used …

Will It Fly? A Computer-Based Aircraft Design Tool, Eric G. Woodfin

Honors Capstone Projects and Theses

No abstract provided.

Multicriteria Mission Route Planning Using A Parallel A* Search, Michael S. Gudaitis

Theses and Dissertations

The Mission Route Planning (MRP) Problem falls into the general class of multicriteria path search problems. Multiple criteria are evaluated to select an optimal aircraft mission route through a hostile environment. Criteria for distance travelled and radar exposure are combined into a single cost function for route evaluation. Radar calculations are performed dynamically. The A* search algorithm is applied to the MRP problem, and a parallel implementation is developed and tested. A unique combination of distributed OPEN lists with a global CLOSED list strategy produced fast execution times on the Paragon. Test cases for scenarios with 15 radars took less …

On Modeling Of A Mobile Multipath Fading Channel, Heng Xiao

Dissertations and Theses

Multipath fading is one of the major practical concerns in wireless communications. A multipath transmission takes place when a transmitted signal arrives at a receiver by two or more paths of different delay. Such multiple paths may be due to atmospheric reflection or refraction, or reflections from buildings or other objects. A multipath fading channel is usually modeled as a time-variant tapped delay system. RAKE receiver can be used to detect the signal from the multipath fading channel. However, the number of delay taps, the time delay of each path, and the tap weight for each delay path need to …

Methodology For Accurate Speedup Prediction, Aruna Chittor

Dissertations and Theses

The effective use of computational resources requires a good understanding of parallel architectures and algorithms. The effect of the parallel architecture and also the parallel application on the performance of the parallel systems becomes more complex with increasing numbers of processors. We will address this issue in this thesis, and develop a methodology to predict the overall execution time of a parallel application as a function of the system and problem size by combining simple analysis with a few experimental results. We show that runtimes and speedup can be predicted more accurately by analyzing the functional forms of the sequential …

Predicting Solute Transport In Natural Streams - A Stochastic Approach, Xueqing Zhou

Dissertations and Theses

The existing theories for predicting longitudinal dispersion in straight open channels have long been recognized as inadequate when applied to natural rivers. These theories tend to grossly underestimate dispersion in real streams since an important mixing mechanism due to nonuniform river cross-section variations is not explicitly taken into account. Recognizing the important role of stream irregularities on solute transport and the analytical difficulties of classical deterministic analysis, we develop a stochastic approach for analyzing solute transport in natural streams. Variations in river width and bed elevation are conveniently represented as one-dimensional random fields, characterized by their autocorrelation functions. Advection and …

The Kinetics Of Volatile Lead Compound Formation During Simulated Hazardous Waste Incineration, Joel Thomas Shor

Doctoral Dissertations

Air pollution from fine metal-containing particles (and vapors) formed during hazardous waste incineration has attracted less attention than other incinerator emissions. Recently, however, metal pollution has become subject to more stringent regulations. The U.S. Environmental Protection Agency has announced limitations on the emissions of ten toxic metals. Pollution control systems that will effectively remove fine (submicron) metal-containing particles from flue gases are difficult to construct. Incinerators have not been designed or operated to minimize the formation of such particles. Industrial-scale incineration testing has produced anomalous results for air emissions of lead and other metals.

To gain a better fundamental understanding …

Airport Security Checkpoint Screener: An Analytical Study Of Job Retention And Attrition Factors, Norman Mark St. Laurent

Master's Theses - Daytona Beach

The proposed research seeks to identify the factors contributing to job retention and job attrition in terms of why an airport security checkpoint screener would try or want to stay on the job or leave the job. By identifying the causes of employee satisfaction and dissatisfaction, and by understanding the integral components of employee turnover can develop appropriate interventions that curb existing retention problems (exceeding 70% annually in most facilities). Aside from the obvious costs affiliated with recruiting, selecting, and training replacement employees, there is likely to be a detrimental impact on the effectiveness of airline passenger screening when a …

The Effects Of The Proposed Larger Aircraft On Airport Capacity In The United States, Kerwin S. Mckenzie

Master's Theses - Daytona Beach

The problem of airport capacity is one that has been around for some time. With air travel projected to increase into the year 2000, Airbus Industrie, Boeing Corporation and McDonnell Douglas are making plans or are in the process of building large transports. Airbus has built the A340/A330 and is planning the now named A3XX, a 600 plus seater. Boeing is currently flying the 747-400 which holds up to 570 passengers. In addition, Boeing rolled out the 777 in June 1994, which holds up to 550 passengers. Douglas is planning the MD-12 with a 700 plus passenger load. The purpose …

Airbus A320/321 Quick Change Market Analysis - A Case Study, Till Christian Mommsen

Master's Theses - Daytona Beach

The purpose of this thesis is to evaluate and compare the Boeing B737 QC to the Airbus A320/321 QC aircraft, and to determine their relative market within a sample airline. The technical design of the two Airbus aircraft in a mixed QC operation were considered with respect to the requirements of a particular airline. Direct operating costs and payload range data for all three aircraft were calculated.

To evaluate the competitiveness of the A320/321 QC under actual conditions, a linear programming fleet planning model was developed that considers more than the direct operating costs of a particular aircraft. The cost …

The Effects Of Non-Uniform Blade Geometries On Cascade And Turbine Stage Performance, Hiroyuki Maeda

Masters Theses

It is known that in-service turbomachinery blades do not have uniform shapes. There are small differences due to blade erosion, manufacturing tolerances, or faulty installation. These differences can be in the size, shape, or relative angles of the blade. In an effort to predict losses resulting from changes in blade thickness and/or blade angles, a two-part investigation has been conducted. A two-dimensional unsteady Navier-Stokes flow analysis has been used to perform numerical experiments.

First, simulations were performed for an isolated cascade. One of the two stators was scaled and/or rotated. Results of the numerical simulations show that increasing the blade …

A Heuristic Procedure For Designing A Cellular Manufacturing System While Minimizing Makespan, Panduranga Badam

Masters Theses

This study is the first of its kind in Group Technology (GT) literature and successfully demonstrates the application of the simulation technique to analyze different alternatives for machine and part grouping problem.

This study considers several aspects such as processing time, sequence of operations, alternative routing, setup time and dynamic shop condition for machine-part grouping. The heuristic developed aims to reduce intercellular moves, setup time and makespan time of parts. It also enables the decision markers to evaluate performance measures and to choose the best alternative at every step of the machine grouping process. Two examples have been used to …

A Computer Allocation Algorithm For Space Problem, Hesham Abdel Aziz Ibrahim

Archived Theses and Dissertations

No abstract provided.

Resilient And Residual Properties Of Egyptian Asphalt Concrete, Medhat Habil Shehata

Archived Theses and Dissertations

No abstract provided.

Flight Control Design Using Mixed H2/Μ Optimization, Douglas D. Decker

Theses and Dissertations

This thesis examines the use of the mixed H2-Microns optimal control synthesis method in the design of a flight control system for the lateral-directional axes of the F-16 Variable Stability In-Flight Simulator Test Aircraft (VISTA). The method is designed to minimize the H2 norm (two-norm) for a given value of microns. This should provide adequate noise and disturbance rejection while maintaining robustness against several types of uncertainties in the system. This thesis finds that, for this problem, the two-norm is not an accurate representation of the outputs of interest. When the two-norm is broken up into its constituent parts an …

Viscoplastic Characterization And Fatigue Modeling Of Titanium Based Metal Matrix Composites, Mark A. Foringer

Theses and Dissertations

Viscoplastic characterization and fatigue modeling of titanium-based metal matrix composites was accomplished by combining a unified viscoplastic theory, a nonlinear micromechanics model, and a linear damage accumulation model. First. Ti 15-3 was characterized using the Bodner-Partom viscoplastic theory. A micromechanics model was then employed in a linear damage accumulation fatigue model to predict the fatigue behavior of titanium based composites. The viscoplastic behavior predictions of the micromechanics model were used to eliminate separately defined time dependent terms in the fatigue model. Also, a new linear damage accumulation model was developed from the fatigue behavior of the composite constituents. Finally, it …

Applications Of ℓ1 And Mixed H2/ℓ1 Optimization, Mark S. Spillman

Theses and Dissertations

This thesis explores the use of ℓ₁ and mixed H2/ℓ1 optimization methods to design flight control systems. ℓ₁ optimization is used to handle tracking issues in the design of digital compensators. Control deflection and rate limitations, overshoot and undershoot limitations and steady-state error requirements are discussed. Model-matching techniques which produce acceptable tracking results with lower order controllers are also examined. New numerical methods for continuous H2/L1 and discrete H2/ℓ1 optimization are presented. These methods are used to design an aircraft controller in continuous and discrete time and the results are compared.

The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge

Theses and Dissertations

This thesis encompassed the design, development, and application of a low-speed, low-force data acquisition system for the AFIT 5-ft Wind Tunnel. The new data acquisition system was designed and developed to measure approximately 0.045 N (about 0.01 lb_f) at nearly 64.4 km/h (40 mph). Verification of the capability was obtained through testing of a cylindrical model. As part of a technology transition program with Wright Laboratory, this new system was used to investigate bicycle front fork blade spacing in order to determine the optimal spacing for minimum drag. As for the minimum drag of a bicycle with an …

A New Drag Measurement System For Wind Tunnel Testing Of The Racing Bicycle And Rider To Determine A Low Drag Configuration, Brian A. Parker

Theses and Dissertations

This study investigated the application of splitter plate effects to reduce the aerodynamic drag of the racing bicycle and rider system. A sensitive, low-force, beam-type, single-component balance was developed to provide drag measurements accurate to within 0.053 N (0.012 lb_f). The performance of the new system was verified by comparing the measured drag on a three-dimensioaal, right-circular cylinder model, 0.127 m (5.0 in) in diameter and 0.610 m (24 in) long, with the results from a commercial balance and a other similar data. The bicycle and rider model consisted of a full-scale mannequin comprising only the hips, legs …

Total Ionizing Dose Effects In Mosfet Devices At 77 K, Kevin J. Daul

Theses and Dissertations

Total ionizing dose effects on thermal oxide and reoxidized nitrided oxide (RNO) MOSFET devices at 77 K were studied. The MOSFETs were immersed in liquid nitrogen and irradiated, using a ⁶⁰Co source, up to 1 Mrad(Si) at a dose rate of 107 rads(Si)-sec. Drain current-gate voltage characteristics were obtained and used to determine threshold voltage and transconductance. At 77 K the subthreshold slopes indicated no observed buildup of interface states in any of the transistors. Furthermore, all transistors experienced very little change in the transconductance. Typical negative shifts in threshold voltage as dose increased were observed in all of …

An Evolutionary Approach To Allocating Tasks In Hard Real-Time Distributed Systems, Christian Lang

Masters Theses

In real-time systems, correctness not only depends on the result of the computation but also on the time at which this result is available. The violation of timing constraints in hard real-time systems can be critical to human life or environment. Therefore, the scheduling algorithm for distributed systems has to allocate tasks to processing nodes so that no timing constraints can be violated. In addition to timing constraints, tasks have precedence and fault-tolerance constraints.

Static scheduling allocates tasks to processing nodes before the tasks are executed. Static scheduling problems are known to be NP-hard [4]. Therefore, heuristic techniques are necessary …

An Investigation And Improvement Of Electrorheological (Er) Fluid Technology, Adil F. Dalal

Masters Theses

The purpose of this research was to investigate and overcome the limitations of Electrorheological (ER) fluids and to introduce this advanced technology at WMU. Electrorheological (ER) Fluids are a special class of fluids, which exhibit a reversible, infinitely variable phase transition from a liquid to a solid/semi-plastic state, in the presence of an electric field.

ER fluids can provide a unique solution to the problems of vibration isolation of systems. The applications are currently limited due to the high voltage requirements, electric power related heating and limited research into wear/abrasive characteristics of ER fluids.

A specially designed and constructed "electro-viscosimeter" …

Investigation Of Boundary Layer And Performance Effects Of Transpiration Cooling Through A Porous Plate In A Rocket Nozzle, David N. Keener

Theses and Dissertations

This study used a range of low blowing ratios with air through an area of porous material in a Mach 2.0 nozzle to quantity the change in boundary layer thickness as a function of blowing ratio. Also, exit and wall Mach number profiles at each blowing ratio were collected to characterize performance losses as a result of blowing. Performance in terms of specific impulse was also studied. As expected, the boundary layer thickness increased and nozzle performance in terms of exit Mach number decreased with increasing blowing ratio.

Fatigue Behavior Of A Cross-Ply Ceramic Matrix Composite At Elevated Temperature Under Tension-Tension Loading, Craig D. Steiner

Theses and Dissertations

This study investigated the fatigue behavior and damage mechanisms of a [0-90]_4s SiC-MAS ceramic matrix composite under tension-tension loading at two elevated temperatures and two frequencies. Stress and strain hystereses, maximum and minimum strain, and modulus of elasticity were evaluated to characterize the material behavior. Microscopy and fractography were used to evaluate damage progression and mechanisms. Fatigue life was independent of frequency at both temperatures.

Next Generation Real-Time Systems: Investigating The Potential Of Partial-Solution Tasks, Robert E. J. Caley

Theses and Dissertations

While the cyclic executive and fixed-priority scheduling strategies have been sufficient to handle traditional real- time requirements. they are insufficient for dealing with the complexities of next-generation real-time systems. New methods of intelligent control must be developed for guaranteeing on-time task completion for real-time systems that are faced with unpredictable and dynamically changing requirements. Implementing real-time processes as partial-solution tasks is one technique that may be beneficial. This type of task. when combined with intelligent control, has the potential for increasing pre-runtime schedulability, system maintainability. and runtime robustness. This research investigates the benefits of partial-solution tasks by experimentally measuring the …

Improving The Performance Of Spiral Antennas By Using Passive Scatterers, Joseph S. Zaren

Theses and Dissertations

The purpose of this study was to explore the viability of improving the performance of cavity-backed antennas. Traditionally antenna cavities are filled with electromagnetic absorber to mitigate interference effects that would otherwise cause the antenna radiation pattern to vary widely at different frequencies. The approach used in this research was to replace the absorber with dielectric slabs, some of which contained arrays of dipoles. These dipole arrays were modeled as frequency selective surfaces using two periodic moment method based - computer programs and one transmission line program. A systematic study was performed that identified the effect of changing the dipole …

Frame Selection Performance Limits For Statistical Image Reconstruction Of Adaptive Optics Compensated Images, Stephen D. Ford

Theses and Dissertations

The U.S. Air Force uses adaptive optics systems to collect images of extended objects beyond the atmosphere. These systems use wavefront sensors and deformable mirrors to compensate for atmospheric turbulence induced aberrations. Adaptive optics greatly enhance image quality; however, wavefront aberrations are not completely eliminated. Therefore, post-detection processing techniques are employed to further improve the compensated images. Typically, many short exposure images are collected, recentered to compensate for tilt, and then averaged to overcome randomness in the images and improve signal-to-noise ratio. Experience shows that some short exposure images in a data set are better than others. Frame selection exploits …

Distributed Interactive Simulation Virtual Cassette Recorder (Dis Vcr): A Datalogger With Variable Speed Replay, Jonathan L. Fortner

Theses and Dissertations

The overall objective of the Distributed Interactive Simulation Virtual Cassette Recorder (DIS VCR) is to add a flexible replay capability to any DIS environment and specifically to the Remote Debriefing Tool (RDT). The DIS VCR's abilities include selective filtering of incoming DIS Protocol Data Units (PDUs), variable-speed replays, ability to pause, fast-forward, rewind, efficient data storage and retrieval, and an interface that simplifies the execution of those functions. The thesis includes a DIS VCR-compatible design for concurrent replay of audio extracted from signal PDUs and an extension to the replay design that supports unmodifiable rendering or receiving applications. For variable-speed …

An Exploration Of Technology Transfer Control: A Case Study Of Wright Laboratory, William K. West

Theses and Dissertations

Federal laboratories, system product centers, and military logistics centers are being challenged to leverage national investments in technology beyond their traditional customer base--technology transfer. Participation in domestic technology transfer is growing at an astounding rate. Additionally, the federal government has invested and continues to invest billions of dollars into active defense conversion, dual-use technology, and technology transfer. The objective of this research is to explore how one government laboratory controls its technology transfer process, in both the near and long terms. This research examines the motives for participating in technology transfer. The researcher presents several of the processes that are …