Engineering Commons^™

A Comparison Of Common Structural Materials, Molly Green

Williams Honors College, Honors Research Projects

This report will compare structural steel, concrete, and lumber through the lenses of mechanical properties, design process, cost, and environmental impact. Steel is a versatile, strong, and lightweight material that comes at a premium price – both financially and environmentally. It is the most expensive material of the three included in this report. This is largely due to its complex manufacturing process that is also responsible for a significant amount of the world’s carbon dioxide emissions. Concrete is significantly less expensive than steel, but the carbon dioxide emissions from manufacturing are approximately equal. Concrete also only performs well in compression …

Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel

Williams Honors College, Honors Research Projects

In this work, the critical pitting temperature (CPT) will be observed for a selection of austenitic (316LN and 24100) and duplex (2205), and lean duplex (2304, 2001) stainless steels in simulated concrete pore solution. To study the influence of temperature on the pitting stability of the stainless steels, three temperatures were tested: 25oC, 45oC, and 65oC for cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS). Electrochemical properties of the interfaces we studied via EIS analysis. Kinetics were studied via CPP testing. To reveal the critical pitting temperature of the stainless steels, cyclic thermammetry was used. Characterization of the pits …

Analysis Of Standardized Concrete Mixes, Riley Graybeal

Williams Honors College, Honors Research Projects

Concrete is one of the most common materials used in construction. It is mass produced throughout the country, with numerous different designs for concrete mixes. A common practice among concrete manufacturers is to use a standardized concrete mix design. These standardized mix designs are pre-tested and are not usually altered frequently. The hypothesis of this research project is that manufacturers do not constantly investigate new ways to save on their mixes, and simply use the same standardized mix designs.

In this research, investigations into what alterations may reduce the cost of standardized mixes began with a baseline mix design provided …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

Compressive Strength Relative To Sustainable Materials In Concrete, Brad Harvey

Williams Honors College, Honors Research Projects

The objective of this study is to determine how integrating abundant waste materials into concrete affects its compressive strength. This research will be used to benefit the construction industry by replacing a portion of a conventional concrete mix (cement, stone, sand, and water) with more sustainable materials. In order to create a more sustainable concrete mixture, the following mix design and methodology was followed.

The initial step was to create an updatable MS Excel spreadsheet to aid in the mix development (the spreadsheet is shown in Appendix A). These sheets allowed for easy transitions from one mix to another by …

Chemical Modification Of Crumb Rubber To Increase Its Bonding With Concrete, Mary T. Mccannon, Kendall J. Sweitzer

Williams Honors College, Honors Research Projects

The hydrophilicity of crumb rubber was increased with wet chemical modification and added to concrete to increase its adhesion with concrete, consequently the compressive strength relative to that of concrete with untreated rubber. Other modification methods were tested on crumb rubber and rubber sheets to yield an increase in hydrophilicity. Certain tests were less reliable for powder testing or tedious and time consuming and concrete materials and rubber may not be homogeneous.

For wet chemical modification, several approaches were attempted. First, crumb rubber was soaked in 5% sodium hydroxide, 5% potassium permanganate and saturated sodium bisulfite, tested for hydrophilicity using …