Engineering Commons^™

Mathematical Model And Experimental Exploration Of The Nanoinjector Lance Array, Nathan C. Toone

Theses and Dissertations

The Nanoinjector Lance Array has been developed to inject foreign material into thousands of cells at once using electrophoresis to attract and repel particles to and from the electrically-charged lances. A mathematical computer model simulating the motion of attracted or repelled proteins informs the design of the nanoinjection lance array system. The model is validated by accurately predicting protein velocity in electrophoresis experiments. A complete analysis of parameters is conducted via simulations and specific research questions regarding the counter electrode of the nanoinjector lance array system are explored using the model. A novel technique for fabricating lance arrays from collapsed …

Mechanical Properties And Mems Applications Of Carbon-Infiltrated Carbon Nanotube Forests, Walter C. Fazio

Theses and Dissertations

This work explores the use of carbon-infiltrated carbon nanotube (CI-CNT) forests as a material for fabricating compliant MEMS devices. The impacts of iron catalyst layer thickness and carbon infiltration time are examined. An iron layer of 7nm or 10nm with an infiltration time of 30 minutes produces CI-CNT best suited for compliant applications. Average maximum strains of 2% and 2.48% were observed for these parameters. The corresponding elastic moduli were 5.4 GPa and 4.1 GPa, respectively. A direct comparison of similar geometry suggested CI-CNT is 80% more flexible than single-crystal silicon. A torsional testing procedure provided an initial shear modulus …

High Frequency Characterization Of Carbon Nanotube Networks For Device Applications, Emmanuel Decrossas

Graduate Theses and Dissertations

This work includes the microwave characterization of carbon nanotubes (CNTs) to design new CNTs-based high frequency components. A novel developed method to extract the electrical properties over a broad microwave frequency band from 10 MHz to 50 GHz of carbon nanotubes (CNTs) in a powder form is performed. The measured scattering parameters (S-parameters) with a performance network analyzer are compared to the simulated one obtained from an in-house computed mode matching technique (MMT). An optimized first order gradient method iteratively changes the unknown complex permittivity parameters to map the simulated S-parameters with the measured one until convergence criteria are satisfied. …

Experimental Study Of Novel Materials And Module For Cryogenic (4k) Superconducting Multi-Chip Modules, Ranjith John

Graduate Theses and Dissertations

The objectives of this proposal are to understand the science and technology of interfaces in the packaging of superconducting electronic (SCE) multichip modules (MCMs) at 4 K. The thermal management issue of the current SCE-MCMs was examined and the package assembly was optimized. A novel thermally conducting and electrically insulating nano-engineered polymer was developed for the thermal management of SCE-MCMs for 4 K cryogenic packaging. Finally, the nano-engineered polymer was integrated as underfill in a SCE-MCM and the thermal and electrical performance of SCE-MCM was demonstrated at 4 K.

Niobium based superconducting electronics (SCE) are the fastest known digital logic …

Vibration Of Carbon Nano-Structures, Sina Arghavan

Electronic Thesis and Dissertation Repository

In this thesis, first the fundamental characterizations of carbon nano-structures and basic atomistic models of the carbon nanotubes and graphitic sheets are reviewed extensively. Different simulation methods used in this field of study are discussed critically. Advantages and shortfalls of each method are reported in detail. A new structural approach based on the lattice atomic structure is selected as an accurate and efficient model for simulating carbon nano-structures. This method is used comprehensively in the present work along with continuous shell and plate theories to study the mechanical and vibrational characteristics of single-walled carbon nanotubes and single and multi-layered graphene …

Fabrication And Characterization Of Hybrid Energy Harvesting Microdevices, Zhongcheng Gong

Doctoral Dissertations

In this dissertation, a hybrid energy harvesting system based on a lead zirconate titanate (PZT) and carbon nanotube film (CNF) cantilever structure has been designed, fabricated and studied. It has the ability to harvest light and thermal radiation energy from ambient energy and convert them to electricity.

The proposed micro-scale energy harvesting device consists of a composite cantilever beam (SU-8/CNF/Pt/PZT/Pt) which is fixed on a silicon based anchor and two electrode pads for wire bonding. The CNF acts as an antenna to receive radiation energy and convert it to heat energy and then transfer to the whole cantilever structure. The …

Microfabrication Of Conductive Polymer Nanocomposite For Sensor Applications, Chaoxuan Liu

LSU Doctoral Dissertations

This dissertation developed novel microfabrication techniques of conductive polymer nanocomposite and utilized this material as a functional element for various physical sensor applications. Microstructures of nanocomposite were realized through novel microcontact printing and laser ablation assisted micropatterning processes. Prototype devices including large-strain strain sensor and highly-sensitive pressure sensor were demonstrated showing distinct advantages over existing technologies. The polymer nanocomposite used in this work comprised elastomer poly(dimexylsiloxane) (PDMS) as polymer matrix and multi-walled carbon nananotubes (MWCNTs) as a conductive nanofiller. To achieve uniform distribution of carbon nanotubes within the polymer, an optimized dispersion process was developed, featuring a strong organic solvent—chloroform, …

Highly Conductive Carbon Nanotube Fibers For Biomedical Applications, Vijoya Sa

All Dissertations

We developed a wet spinning process for the formation of polymeric fibers with high loading of single walled carbon nanotubes. The dissertation consists of five chapters. In the first chapter, the research goals were formulated and the art and technologies of fiber spinning from carbon nanotubes were critically analyzed. The next three chapters report the original results. Last chapter summarizes all the findings.
In the second chapter, we describe a surfactant based method of stabilization of carbon nanotube dispersions. The conditions of stability of nanotube dispersions in aqueous solutions of sodium dodecyl sulfate were analyzed. Using surface tension isotherms, the …

On Developing Novel Energy-Relates Nanostructured Materials By Atomic Layer Deposition, Xiangbo Meng

Electronic Thesis and Dissertation Repository

ABSTRACT

This thesis presents the fabrication of a series of novel nanostructured materials using atomic layer deposition (ALD). In contrast to traditional methods including chemical vapor deposition (CVD), physical vapor deposition (PVD), and solution-based processes, ALD benefits the synthesis processes of nanostructures with many unrivalled advantages such as atomic-scale control, low temperature, excellent uniformity and conformality. Depending on the employed precursors, substrates, and temperatures, the ALD processes exhibited different characteristics. In particular, ALD has capabilities in fine-tuning compositions and structural phases. In return, the synthesis and the resultant nanostructured materials show many novelties.

This thesis covers ALD processes of four …

Molecular Dynamics Study Of Particle Impact Induced Bond Breaking Of Single-Walled Carbon Nanotubes And Quality Factors Of Nanocomposite Structures, Puroorava Annapaneni

All Theses

Part A
Injection of particles to the side wall of single-walled carbon nanotubes (SWCNT) has been employed for doping and storage of particles on SWCNTs. In addition, particle bombardment can be used to cut and modify graphene structures. While the collision of hydrogen atoms with SWCNTs has been extensively studied, collision dynamic behavior of heavy particles with SWCNTs has not been well understood. To facilitate a better understanding of the particle-SWCNT collision process, in this work, we study the impact of five noble gas atoms (He, Ne, Ar, Kr, Xe) with SWCNTs and investigate particle impact induced CNT bond breaking …

Computational Analysis Of Structural Transformations In Carbon Nanostructures Induced By Hydrogenation, Andre R. Muniz

Open Access Dissertations

Carbon nanomaterials, such as carbon nanotubes and graphene, have attracted significant interest over the past several years due to their outstanding and unusual combination of physical properties. These properties can be modified in a controllable way by chemical functionalization in order to enable specific technological applications. One example is hydrogenation, achieved by the exposure of these materials to a source of atomic hydrogen. This process has been considered for hydrogen storage purposes and for the control of the band gap of these materials for applications in carbon-based electronics. Hydrogen atoms are chemisorbed onto the surface of these materials, introducing sp3-hybridized …

A Study On The Applications And Toxicity Assessments Of Carbon Nanotubes In Tissue Engineering, Rena Baktur

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Carbon nanotubes (CNTs) are one of the most popular nanomaterials. There has been increasing interest in the development and applications of carbon nanotubes due to their huge potential in industrial and medical applications. Recent applications of carbon nanotubes include development of scaffolds and drug delivery systems. Despite rapidly emerging applications of CNTs, little is known about the impact of CNTs on cellular processes, especially mesenchymal stem cell (MSC)'s differentiation. Also, the effects of nanoparticle exposure under different conditions on cellular responses have not been well characterized yet.

To characterize the effects of CNTs on creating nanoscale scaffolds for tissue engineering, …

Straightness Of Growth For Carbon Nanotube Microelectromechanical Systems, Kellen S. Moulton

Theses and Dissertations

The purpose of this research is to examine the effect of iron catalyst thickness on the straightness of growth of carbon nanotube microelectromechanical systems (CNT-MEMS). One of the key benefits of CNT-MEMS is that they can potentially have very high aspect ratios. One of the challenges in attaining these high aspect ratios is maintaining device straightness; as these devices get taller, the edges tend to curve rather than grow straight vertically. Scanning electron mi- croscope images of samples grown using various iron catalyst thicknesses show that both straight growth and relatively good edge definition can be achieved using iron thicknesses …

Atomic And Electronic Structure Studies Of Nano-Structured Systems : Carbon And Related Materials, Sumit Saxena

Dissertations

Modeling in the framework of density functional theory has been conducted on carbon nanotubes and graphene nano-structures. The results have been extended to non-carbon systems such as boron nanostructures. Computational studies are complemented by experimental methods to refine the structural models and obtain a better understanding of the electronic structure.

It is observed that the zigzag edged bilayered graphene nanoribbons are highly unstable as compared to their armchair counterparts. A novel approach has been proposed for the patterning of chirality/diameter controlled single walled carbon nanotubes. Nanotube formation is found to be assisted by edge ripples along with the intrinsic edge …

Strengthening Potential Of Single-Walled Carbon Nanotubes In Phenolic Resin Composites, Brittany Kerr

Electronic Theses and Dissertations

Strengthening potential of single-walled carbon nanotubes (SWCNTs) in a phenolic resin composite was evaluated by characterization of purified and phenyl sulfonated SWCNTs, investigation of the load transfer capability of the purified SWCNTs, and characterization of the composites. Purified and phenyl sulfonated SWCNTs, as well as their composites, were examined by Raman spectroscopy, thermogravimetric analysis, scanning electron microscopy equipped with energy dispersive spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and ultra violet-visible spectrometry. Fabrication of the SWCNT/phenolic resin composite was performed by first dispersing the SWCNTs in ethylene glycol and then homogenizing the mixture with phenolic resin. The ethylene glycol was …

Characterization Of Poly(Methyl Methacrylate Based Nanocomposites Enhanced With Carbon Nanotubes, Andrew Jonathan Placido

University of Kentucky Master's Theses

The viscoelastic relaxation dynamics of a series of poly(methyl methacrylate) [PMMA] based nanocomposites filled with carbon nanotubes have been studied using dynamic mechanical analysis and broadband dielectric spectroscopy. The networks were prepared using four methods: (i) melt mixing, (ii) solution processing, (iii) in-situ polymerization, and (iv) polymer grafting. Nanotube modifications included surface oxidation via acid exposure and surface functionalization for polymer grafting. The effect of variations in processing method and nanotube modification on glass transition temperature (T_g) and relaxation dynamics was investigated. The relaxation behavior of the nanocomposites was sensitive to processing method and nanotube functionalization. Nanotube loading …

Single-Walled Carbon Nanotube Device Fabrication Using Spin Coating Of Dispersions, Paul Jeremy Hummel

Doctoral Dissertations

This research looks at ways to utilize already synthesized carbon nanotubes (CNT) to manufacture electrical connections using current tools and fabrication methods employed in the semiconductor industry. Purchased single-walled carbon nanotubes (SWNT) are separated and placed in suspension using poly(sodium styrene sulfonate) (PSS). The PSS non-covalently bonds to the SWNTs, causing them to repel each other due to the negative charge of the PSS. The suspension of SWNTs is spin coated over a processed silicon (Si) wafer with fabricated trenches. A Si wafer with a top silicon dioxide (SiO 2) layer is spin coated with Shipley 1827 photoresist. UV light …

Aquatic Bacteria Removal Using Carbon Nanotubes, Suvish Melanta

Biological and Agricultural Engineering Undergraduate Honors Theses

The purpose of this project is to explore the functionality of carbon nanotubes as a bacterial removal method, specifically towards water-borne bacterial pathogens in wastewater by utilizing its unique magnetic and bacteria-binding properties. The general protocol set for this research follows five steps: 1) Preparation of wastewater media, 2) preparation of CNT culture, 3) preparation of reaction mixture with CNTs for bacterial binding, 4) magnetic separation of bacteria-bound-CNT clusters and, 5) assessment of supernatant. The CNTs effectively removed bacterial contaminants in the wastewater (10%, v/v) after the sand filtration process from the Paul R. Noland Wastewater Facility at Fayetteville, Arkansas. …

Novel Catalysts For The Production Of Co- And Co2-Free Hydrogen And Carbon Nanotubes By Non-Oxidative Dehydrogenation Of Hydrocarbons, Wenqin Shen

University of Kentucky Doctoral Dissertations

Non-oxidative dehydrogenation of hydrocarbons is an attractive alternative route for the production of CO- and CO₂-free hydrogen. It will satisfy a major requirement for successful utilization of polymer electrolyte membrane (PEM) fuel cells (< 10 ppm CO) and sequestering carbon as a potentially valuable by-product, carbon nanotubes (CNTs). Due to the deposition of carbon on the surface of catalyst particles during the reaction, catalyst performance, life-time, and purification of the generated carbon product, are significant issues to solve in order to make the process practically feasible. The scope of this thesis includes: the development of novel Fe, Ni, and Fe-Ni catalysts supported on a Mg(Al)O support to achieve improved catalytic performance with easily-purified CNTs; evaluation of catalysts for ethane/methane dehydrogenation at moderate reaction temperatures; and study of activation and deactivation mechanisms by a variety of characterization techniques including TEM, HRTEM, XRD, Mössbauer spectroscopy, and x-ray absorption fine structure (XAFS) spectroscopy. The Mg(Al)O support was prepared by calcination of synthetic MgAl-hydrotalcite with a Mg to Al ratio of 5. The catalysts were prepared either by conventional incipient wetness method or by a novel nanoparticle impregnation method, where the monodisperse catalyst nanoparticles were prepared in advance by thermal decomposition of a metal-organic complex in an organic-phase solution and then dispersed onto the Mg(Al)O support. Dehydrogenation of undiluted methane was conducted in a fix-bed plug-flow reactor. Before reaction, the catalysts were activated by reduction in hydrogen. Fe-based catalysts exhibit a higher hydrogen yield at temperature above 600ºC compared with monometallic Ni catalyst. FeNi-9 nm/Mg(Al)O, Fe-10 nm/Mg(Al)O and Fe-5 nm/ Mg(Al)O nanoparticle catalysts show much improved performance and longer life-times compared with the corresponding FeNi IW/Mg(Al)O and Fe IW/Mg(Al)O catalysts prepared by incipient wetness. 10 nm is the optimum particle size for methane dehydrogenation. Addition of Ni to Fe forming a bimetallic FeNi alloy catalyst enhances the catalytic performance at the temperatures below 650ºC. Metallic Fe, Ni, FeNi alloy and Fe-Ni-C alloy, unstable iron carbide are all catalytically active components. Catalysts deactivation is due to the carbon encapsulation. The carbon products are in the form of stack-cone CNTs (SCNTs) and multi-walled CNTs (MWNTs), depending on the reaction temperature and catalyst composition. The growth of CNTs follows a tip growth mechanism and the purity of cleaned CNTs is more than 99.5%.

High Strength E-Glass/Cnf Fibers Nanocomposite, Esam Abu-Zahra

ETD Archive

Glass fibers are among the most versatile industrial materials known today, where 4 billion pounds of glass are used every year. They are readily produced from raw materials, which are available in virtually unlimited supply. To compensate for its low tensile strength, glass is usually mixed with other materials such as nanofibers and nanospheres, to form what is called "glass nanocomposites". Nevertheless, glass composites still suffer from different weaknesses such as: poor dispersion, poor alignment and orientation of reinforcing materials (due to their short lengths relative to the defect sizes in the composite matrices), in addition to the difficulties associated …

Synthesis, Characterization And Application Of Pd-Pt Bimetallic Nanoparticles And Carbon Nanotubes Supported Nanocomposites, Guoqiang Ren

Masters Theses

"A study on the synthesis of Pd-Pt alloy nanoparticles and composition evolution of the alloys was reported. The synthesis followed a hot organometallic route, with Pd and Pt acetylacetonate as the metal precursors and trioctylphosphine as the solvent. The size of the Pd-Pt nanoparticles narrowed down with time and reached a final size of 3.5 nm in about 10 min. The alloy compositions evolved with time and reached the preset Pd to Pt ratio of precursors in 120 min. An atomic exchange process between the Pt-TOP complex and the Pd atoms at the nanoparticle surface was proposed to elucidate this …

Processing And Study Of Carbon Nanotube / Polymer Nanocomposites And Polymer Electrolyte Materials, Muthuraman Harish

Electronic Theses and Dissertations

The first part of the study deals with the preparation of carbon nanotube/polymer nanocomposite materials. The dispersion of multi-walled carbon nanotubes (MWNTs) using trifluoroacetic acid (TFA) as a co-solvent and its subsequent use in polymer nanocomposite fabrication is reported. The use of carbon nanotube/ polymer nanocomposite system for the fabrication of organic solar cells is also studied. TFA is a strong but volatile acid which is miscible with many commonly used organic solvents. Our study demonstrates that MWNTs can be effectively purified and readily dispersed in a range of organic solvents including dimethyl formamide (DMF), tetrahydrofuran (THF), and dichloromethane when …

Processing And Characterization Of High Performance Structural Nanocomposites, Dennis C. Working

Mechanical & Aerospace Engineering Theses & Dissertations

Carbon nanotubes are considered to be a revolutionary material breakthrough due to their unique combination of properties. While many applications for SWCNTs have been projected, realization of these potential uses have been hampered by the high cost of limited supplies of high quality SWCNTs and the difficulty in the development of a suitable processing method that does not damage the filler thus diminishing the desirable properties of this material. In spite of these technical challenges, their potential to enable the fabrication of multifunctional materials is being investigated in earnest. The goal of this thesis is to investigate the feasibility of …

Carbon Nanotubes And Tungsten Oxide Nanorods: Synthesis And Applications, Bing Xiao

Electrical & Computer Engineering Theses & Dissertations

Synthesis and applications of two types of one-dimensional nanomaterials, carbon nanotubes (CNTs) and tungsten oxide nanorods, are investigated in this dissertation. Multi-walled CNTs have been successfully synthesized using two types of chemical vapor deposition (CVD) methods: microwave plasma enhanced CVD and atmospheric pressure thermal CVD. CNTs and their synthesis processes are characterized with various analysis techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, and optical emission spectroscopy. Ultra-thin and high quality multi-walled CNTs are discovered in CNT films produced by MPCVD, which exhibit good field emission performance that is found to be dependent on the synthesis …

Arc-Discharge In Solution: A Novel Synthesis Method For Carbon Nanotubes And In Situ Decoration Of Carbon Nanotubes With Nanoparticles, Debasis Bera

Electronic Theses and Dissertations

Nanotechnology has reached the status of the 21st century's leading science and technology based on fundamental and applied research during the last two decades. An important feature of nanotechnology is to bridge the crucial dimensional gap between the atomic and molecular fundamental sciences and microstructural scale of engineering. Accordingly, it is very important to have an in-depth understanding of the synthesis of nanomaterials for the use of state-of-the-art high technological devices with enhanced properties. Recently, the 'bottom-up' approach for the fabrication of nanomaterials has received a great deal of attention for its simplicity and cost effectiveness. Tailoring the various parameters …

Characterization Of Electrosprayed Poly(Vinylidene Fluoride)/Cnt Nanocomposite, Ihab Maher Abdelsayed

Theses and Dissertations

PVDF, Poly(vinylidene fluoride), is a polymer that has been studied for over four decades due to its good electromechanical properties, stability, and durability in various environments. Currently, PVDF is the only commercially available piezoelectric polymer. PVDF is a polymorph, which indicates the presence of several crystalline phases such as α, β, γ, and δ-phase. Oriented β-phase PVDF exhibits ferroelectric properties and displays the largest piezoelectricity amongst the four phases, which makes it the most desirable phase. Preparing oriented β-phase PVDF is a multi-step process, which is cost intensive, due to the time, labor and energy utilized. The main goal of …

Deposition Of Carbon Layers From Cyclohexane By Thermal Chemical Vapor Deposition, Bharath Thiruvengadachari

LSU Master's Theses

The overall aim of this thesis is to deposit carbon layers by thermal Chemical Vapor Deposition (CVD) and investigate the effects of process parameters on the morphology and structure of the deposited carbon layers. Cyclohexane (C6H12) hydrocarbon is the precursor material used as the source of carbon. A 20% Cu- 80% Ni alloy, deposited by RF magnetron sputtering and annealed at the growth temperature either in an argon flow or in 10% hydrogen-90% argon flow, is used as a catalyst prior to carbon film deposition by CVD. The CVD temperature is varied between 550 0C and 800 0C. The Cu-Ni …

Field Emission Based Sensors Using Carbon Nanotubes, Changkun Dong

Physics Theses & Dissertations

A number of sensitive applications would be greatly benefited by the development of better cold cathodes that employ the electron field emission process. Among the many kinds of field emitters that could be tried, carbon nanotubes (CNT) have a number of distinct advantages because of their unique geometrical structure, chemical inertness, mechanical stiffness, and high thermal and electrical conductivities. This dissertation describes research in which CNT cathodes were fabricated and their emission characteristics were measured.

Multi-walled carbon nanotubes (MWNT) were grown by chemical vapor deposition (CVD) on various substrates: Ni and Hastelloy gauze, 304 stainless steel (SS) plates, and Ni-coated …