Engineering Commons^™

Understanding The Surface Fouling Mechanism Of Ultrananocrystalline Diamond Microelectrodes Using Microfluidics For Neurochemical Detection, An-Yi Chang

Doctoral Dissertations

Electrochemical methods are widely used for chronic neurochemical sensing, but thus far, the organic solution redox reactions fouled the electrodes' surface. It caused the reduction of sensitivity and the electrodes' lifetime.

Here, we present the boron-doped nanocrystalline diamond microelectrodes (BDUNCD) as the next generation electrode material for neurochemical sensor development. To aid in long-term chronic monitoring of neurochemicals, they have a wide window of electrochemical potential, extremely low background current, and excellent chemical inertness. The main research goal is to reduce the rate of electrode fouling due to the reaction by-products, and significantly extend their useful lifetime.

We systematically characterize …

Electrochemical Behavior Of Dense Electrodes For Impedancemetric Nox Sensors, Nabamita Pal

Doctoral Dissertations

NOx (NO and NO2) exhaust gas sensors for diesel powered vehicles have traditionally consisted of porous platinum (Pt) electrodes along with a dense ZrO2 based electrolyte. Advancement in diesel engine technology results in lower NOx emissions. Although Pt is chemically and mechanically tolerant to the extreme exhaust gas environment, it is also a strong catalyst for oxygen reduction, which can interfere with the detection of NOx at concentrations below 100 ppm. Countering this behavior can add to the complexity and cost of the conventional NO x sensor design. Recent studies have shown that dense electrodes are less prone to heterogeneous …

Full Simulation For The Qweak Experiment At 1.16 And 0.877 Gev And Their Impact On Extracting The Pv Asymmetry In The N→Δ A Transition, Hend Abdullah Nuhait

Doctoral Dissertations

The Qweak project is seeking to find new physics beyond the Standard Model. It is aimed to measure the weak charge of the proton, which has never been measured, at 4% precision at low momentum transfer. The experiment is performed by scattering electrons from protons and exploiting parity violation in the weak interaction at low four-momentum transfer.

In this experiment, two measurements were considered: which are elastic and inelastic. The elastic is to measure the proton's weak charge. In addition, the inelastic asymmetry measurement, which will extract the low energy constant dΔ. That measurement works in the neutral current …

Stretching The Limits Of Dynamic Range, Shielding Effectiveness, And Multiband Frequency Response, Matthew J. Hartmann

Doctoral Dissertations

In this dissertation, an RF MEMS variable capacitor suitable for applications requiring ultrawide capacitive tuning ranges is reported. The device uses an electrostatically tunable liquid dielectric interface to continuously vary the capacitance without the use of any moving parts. As compared to existing MEMS varactors in literature, this device has an extremely simple design that can be implemented using simple fabrication methods that do not necessitate the use of clean room equipment. In addition, this varactor is particularly suited for incorporating a wide range of liquid dielectric materials for specific tuning ratio requirements.

Additionally, the shielding effectiveness performance of graphene-doped …

Improvement Of Fluorescence-Based Microfluidic Dna Analyzers, Collin Tranter

Doctoral Dissertations

A tremendous effort continues in the development of micro-total-analysis-systems; in support of this, many chemical passivation methods have been developed to enhance the biocompatibility of such microfluidic systems. However, the suitability of these passivation techniques to many fluorescence-based assays still remains inconsistent. This part of this work is focused on the performance of a third generation intercalating DNA dye when used within microfluidic devices treated with a select variety of passivating coatings. The results of these tests indicate that passivation coatings which are intended to shed DNA based on electrostatic repulsion will in fact imbibe the fluorescent DNA intercalating dye …

Development Of A Nonlinear Model For The Prediction Of Response Times Of Glucose Affinity Sensors Using Concanavalin A And Dextran And The Development Of A Differential Osmotic Glucose Affinity Sensor, Louis G. Reis

Doctoral Dissertations

With the increasing prevalence of diabetes in the United States and worldwide, blood glucose monitoring must be accurate and reliable. Current enzymatic sensors have numerous disadvantages that make them unreliable and unfavorable among patients. Recent research in glucose affinity sensors correct some of the problems that enzymatic sensors experience. Dextran and concanavalin A are two of the more common components used in glucose affinity sensors. When these sensors were first explored, a model was derived to predict the response time of a glucose affinity sensor using concanavalin A and dextran. However, the model assumed the system was linear and fell …

Synthesis, Characterization, And Activity Of Co/Fe Alumina/Silica Supported Ft Catalysts And The Study Of Promoter Effect Of Ruthenium, Sunday Azubike Esumike

Doctoral Dissertations

The alumina and hybrid alumina-silica FT catalyst were prepared by one-step solgel/oil-drop methods using metal-nitrate-solutions (method-I), and nanoparticle-metaloxides (method-2). The nanoparticle-metal-oxides did not participate in solubility equilibria in contrast to metal nitrate in method-1 causing no metal ion seepage; therefore, method-2 yields higher XRF metal loading efficiency than method-1. The thermal analysis confirmed that the metal loading by method-1 and method-2 involved two different pathways. Method-1 involves solubility equilibria in the conversion of metal-nitrate to metal- hydroxide and finally to metal-oxide, while in method-2 nanoparticle-metal-oxide remained intact during sol-gel-oil-drop and calcination steps.

The alumina supported catalysts were dominated by γ-alumina …

A Study Of Mathematics Achievement, Placement, And Graduation Of Engineering Students, Sara Hahler Blazek

Doctoral Dissertations

The purpose of this study was to determine how background knowledge impacts freshmen engineering students' success at Louisiana Tech University in terms of grades in two different freshman classes and graduation. To determine what factors impact students, three different studies were implemented. The first study used linear regression to analyze which demographic and academic variables significantly impacted freshman math and engineering courses. Using regression discontinuity, the second study determined if the university's placement requirement for Pre-Calculus was appropriate. The final study analyzed factors that impact graduation for engineering students as well as other disciplines to determine which significant variables were …

Design, Modeling, Fabrication, And Testing Of A Multistage Micro Gas Compressor With Piezoelectric Unimorph Diaphragm And Passive Microvalves For Microcooling Applications, Shawn Thanhson Le

Doctoral Dissertations

This dissertation investigates the development of a multistage micro gas compressor utilizing multiple pump stages cascaded in series to increase the pressure rise with passive microvalves and piezoelectric unimorph diaphragms. This research was conducted through modeling, simulation, design, and fabrication of the microcompressor and its components. A single-stage and a two-stage microcompressor were developed to demonstrate and compare the performance and effectiveness of using a cascaded multistage design.

Steady fluid flow through static microvalves structure was studied to gain insight on its gas flow dynamics and characteristics. Transient analysis combined with the structure's interaction was investigated with an analytical model …

Expanding The Applications Of Poly(Dimethylsiloxane) In Biomicrofluidics, Sawyer D. Stone

Doctoral Dissertations

This work aims to create novel applications for poly(dimethylsiloxane) (PDMS) in the field of biomicrofluidics through oxidative stress detection, doping of the polymer for intentional leaching into microdevices, and the development of low-cost implements for fabricating PDMS microfluidic devices. PDMS has become the polymer of choice for research in microfluidics due to its optical clarity, ease of fabrication, flexibility in design, good mechanical properties, and the ability to chemically modify the surface.

Biomicrofluidics enables the rapid throughput and analysis of small biological samples requiring less time investment and reagent use than traditional macroscale laboratory techniques. Polymer devices are inexpensive, easily …

Anxiolytic Effects Of Propranolol And Diphenoxylate On Mice And Automated Stretch-Attend Posture Analysis, Kevin Scott Holly

Doctoral Dissertations

The prevention of social anxiety, performance anxiety, and social phobia via the combination of two generic drugs, diphenoxylate HC1 (opioid) plus atropine sulfate (anticholinergic) and propranolol HCl (beta blocker) was evaluated in mice through behavioral studies. A patent published on a September 8, 2011 by Benjamin D. Holly, US 2011/0218215 Al, prompted the research. The drug combination of diphenoxylate and atropine plus propranolol could be an immediate treatment for patients suffering from acute phobic and social anxiety disorders. Demonstrating the anxiolytic effects of the treatment on mice would validate a mouse model for neuroscientist to be used to detect the …

Potential Applications For Halloysite Nanotubes Based Drug Delivery Systems, Lin Sun

Doctoral Dissertations

Drug delivery refers to approaches, formulations, technologies, and systems for transporting a drug in the body. The purpose is to enhance the drug efficacy and to reduce side reactions, which can significantly improve treatment outcomes. Halloysite is a naturally occurred alumino-silicate clay with a tubular structure. It is a biocompatible material with a big surface area which can be used for attachment of targeted molecules. Besides, loaded molecules can present a sustained release manner in solution. These properties make halloysite nanotubes (HNTs) a good option for drug delivery.

In this study, a drug delivery system was built based on halloysite …

Generalized Partial Directed Coherence And Centrality Measures In Brain Networks For Epileptogenic Focus Localization, Joshua Aaron Adkinson

Doctoral Dissertations

Accurate epileptogenic focus localization is required prior to surgical resection of brain tissue for treatment of patients with intractable temporal lobe epilepsy, a clinical need that is partially fulfilled to date through a subjective, and at times inconclusive, evaluation of the recorded electroencephalogram (EEG). Using brain connectivity analysis, patterns of causal interactions between brain regions were derived from multichannel EEG of 127 seizures in nine patients with focal, temporal lobe epilepsy (TLE). The statistically significant directed interactions in the reconstructed brain networks were estimated from three second intracranial multi-electrode EEG segments using the Generalized Partial Directed Coherence (GPDC) and validated …

Lab-On-A-Chip Nucleic-Acid Analysis Towards Point-Of-Care Applications, Varun Lingaiah Kopparthy

Doctoral Dissertations

Recent infectious disease outbreaks, such as Ebola in 2013, highlight the need for fast and accurate diagnostic tools to combat the global spread of the disease. Detection and identification of the disease-causing viruses and bacteria at the genetic level is required for accurate diagnosis of the disease. Nucleic acid analysis systems have shown promise in identifying diseases such as HIV, anthrax, and Ebola in the past. Conventional nucleic acid analysis systems are still time consuming, and are not suitable for point-ofcare applications. Miniaturized nucleic acid systems has shown great promise for rapid analysis, but they have not been commercialized due …

Studies On The Electrical Transport Properties Of Carbon Nanotube Composites, Taylor Warren Tarlton

Doctoral Dissertations

This work presents a probabilistic approach to model the electrical transport properties of carbon nanotube composite materials. A pseudo-random generation method is presented with the ability to generate 3-D samples with a variety of different configurations. Periodic boundary conditions are employed in the directions perpendicular to transport to minimize edge effects. Simulations produce values for drift velocity, carrier mobility, and conductivity in samples that account for geometrical features resembling those found in the lab. All results show an excellent agreement to the well-known power law characteristic of percolation processes, which is used to compare across simulations. The effect of sample …

Investigation Of Small-Scale Thermal Recovery And Storage Systems, Suvhashis Thapa

Doctoral Dissertations

An approach to recover and store waste heat is presented in this dissertation. The waste heat is the energy that is rejected to the environment without being put to practical use and it is a result of both equipment inefficiency and thermodynamic limitation on the equipment and the process. In a typical Otto cycle, for instance, out of the total energy consumed by the system, only one-third of the energy is converted into useful work and the rest is discharged in the environment as waste heat [1]. For a spark ignition, a 1.4 liters internal combustion engine with the thermal …

Experimental And Numerical Evaluation Of A New Composite Pressure Pipe For A Trenchless Rehabilitation Technology, Xuanchen Yen

Doctoral Dissertations

The information presented in this dissertation is based on research work conducted at Trenchless Technology Center (TTC) at Louisiana Tech University. This work was performed through a contract with China University of Geoscience (CUG) for a gas company. China's gas pipelines need replacement or rehabilitation after 15 to 30 years of service. China's gas industry is looking for suitable techniques to transfer into their market.

When compared to conventional excavation pipeline renewal or replacement methods, there are obvious advantages of TRT for gas pipelines that can impact the triple bottom-line of economic, social and environmental benefits. An introduction of TRT …

Experimental Investigation And Numerical Simulation Of A Copper Micro-Channel Heat Exchanger With Hfe-7200 Working Fluid, Eric Borquist

Doctoral Dissertations

Ever increasing cost and consumption of global energy resources has inspired the development of energy harvesting techniques which increase system efficiency, sustainability, and environmental impact by using waste energy otherwise lost to the surroundings. As part of a larger effort to produce a multi-energy source prototype, this study focused on the fabrication and testing of a waste heat recovery micro-channel heat exchanger. Reducing cost and facility requirements were a priority for potential industry and commercial adoption of such energy harvesting devices. During development of the micro-channel heat exchanger, a new fabrication process using mature technologies was created that reduced cost, …

Nano Clay-Enhanced Calcium Phosphate Cements And Hydrogels For Biomedical Applications, Udayabhanu Jammalamadaka

Doctoral Dissertations

Biomaterials are used as templates for drug delivery, scaffolds in tissue engineering, grafts in surgeries, and support for tissue regeneration. Novel biomaterial composites are needed to meet multifaceted requirements of compatibility, ease of fabrication and controlled drug delivery. Currently used biomaterials in orthopedics surgeries suffer limitations in toxicity and preventing infections. Polymethyl methacrylate (PMMA) used as bone cement suffers from limitations of thermal necrosis and monomer toxicity calls for development of better cementing biomaterials. A biodegradable/bioresorbable cement with good mechanical properties is needed to address this short coming. Metal implants used in fixing fractures or total joint replacement needs improvements …

Energy Harvesting Using Photovoltaic And Betavoltaic Devices, Ashish Sharma

Doctoral Dissertations

There is an important need for improvement in both cost and efficiency of photovoltaic cells. For improved efficiency, a better understanding of solar cell performance is required. An analytical model of thin-film silicon solar cell, which can provide an intuitive understanding of the effect of illumination on its charge carriers and electric current, is proposed. The separate cases of homogeneous and inhomogeneous charge carrier generation rates across the device are investigated. This model also provides for the study of the charge carrier transport within the quasi-neutral and depletion regions of the device, which is of an importance for thin-film solar …

Immobilization Of Cellulase For Large Scale Reactors To Reduce Cellulosic Ethanol Cost, Dezhi Zhang

Doctoral Dissertations

Cellulosic ethanol is an alternative renewable energy source. Cellulase used in the production of cellulosic ethanol is very expensive. The difficulty in separating cellulase from the cellulose solution after the hydrolysis process limits the reusability of the cellulase, which highly precludes the scales of this application because of the high cost of the enzyme. Immobilization of cellulase provides a promising approach to allow the enzyme to be recycled, thus reducing the production cost. This research focused on immobilizing cellulase for reuse to reduce the cellulosic ethanol cost.

Four immobilization techniques were explored for the immobilization of cellulase on four different …

Clay Nanotube Composites For Antibacterial Nanostructured Coatings, Christen J. Boyer

Doctoral Dissertations

A surging demand for the development of new antimicrobial nanomaterials exists due to the frequency of medical device-associated infections and the transfer of pathogens from highly touched objects. Naturally occurring halloysite clay nanotubes (HNTs) have shown to be ideal particles for polymer reinforcement, time-release drug delivery, nano-reactor synthesis, and as substrate material for nanostructured coatings.

This research demonstrates the feasibility of a novel method for coating HNTs with metals for antibacterial applications. The first ever ability to coat HNTs through electrolysis was developed for customizable and multi-functional antibacterial nanoparticle platforms. HNTs were investigated as substrate for the deposition of copper …

Mutlifunctional Platforms For Gene And Drug Delivery For Cancer Therapy, Jeffery J. Ambrose Jr.

Doctoral Dissertations

The National Cancer Institute and the American Cancer Society estimate that 1.6 million new cancer incidences and over half a million cancer related deaths occur annually [1][2]. Cancer the second most common cause of death in the United States [1], [2]. Although the causes of cancer can vary depending on cell type, all or almost all instances of cancer arise from a mutation or from an abnormal activation of the cellular genes that control cell growth and mitosis [3].

Treatment of a given cancer type depends on the subtype, stage and progression of the cancer. Varieties of cancer therapy include …

Tunable Controlled Release Of Molecular Species From Halloysite Nanotubes, Divya Narayan Elumalai

Doctoral Dissertations

Encouraged by potential applications in rust coatings, self-healing composites, selective delivery of drugs, and catalysis, the transport of molecular species through Halloysite nanotubes (HNTs), specifically the storage and controlled release of these molecules, has attracted strong interest in recent years. HNTs are a naturally occurring biocompatible nanomaterial that are abundantly and readily available. They are alumosilicate based tubular clay nanotubes with an inner lumen of 15 nm and a length of 600-900 nm. The size of the inner lumen of HNTs may be adjusted by etching. The lumen can be loaded with functional agents like antioxidants, anticorrosion agents, flame-retardant agents, …

Detecting And Screening Of The Prostate Cancer By Using An Optical Nanoporous Thin-Film Sensor, Salah Eldeen Mofleh Alzghoul

Doctoral Dissertations

Prostate cancer (PC) affects elderly men more than young men. The currently used cancer biomarker, prostate-specific antigen (PSA), highly overestimates PC population. Men with high PSA levels often have to go through unnecessary, but physically painful, and expensive prosesses, such as prostate biopsies. Finding a prostate cancer marker that is produced selectively by cancer, but not by normal prostate cells will increase the reliability of PC test. In 2006, our collaborator (Dr. Girish Shah) discovered a novel protein, referred as neuroendocrine marker (NEM), secreted only by malignant prostate cells and released in blood circulation.

To examine whether the combined NEM-PSA …

Impedance Characterization Of Ysz Based Nox Sensors, Ling Cui

Doctoral Dissertations

Yttria-stabilized zirconia has been utilized as an electrolyte of SOFC (Solid Oxide Fuel Cell) studies for years. It is also preferred as the electrolyte for solid state electrochemical sensor which is able to measure nitrogen oxides in the exhaust system. Electrochemical Impedance Spectroscopy method yields the change in impedance which is caused by an electron exchange of NO x gases at the sensing electrodes. From the EIS data, the fractional change in the phase angle is calculated for detecting sensor sensitivity.

Considering the fabrication of a sensor, several variables have been investigated which include the choice of electrolyte processing, sensing …

Size Specific Transfection To Mammalian Cells By Micropillar Array Electroporation, Yingbo Zu

Doctoral Dissertations

Electroporation serves as a promising non-viral gene delivery approach, while its current configurations carry drawbacks associated with high-voltage electrical pulses and heterogeneous treatment on individual cells. Here, we developed a new micropillar array electroporation (MAE) platform to advance the delivery of plasmid DNA and RNA to mammalian cells. By introducing well-patterned micropillar array on the electrode surface, the number of pillars each cell faces varies with its cell membrane surface area, despite their large population and random locations. In this way, cell size specific electroporation is conveniently done and contributed to a 2.5~3 fold increase on plasmid DNA transfection and …

Improving Nano-Drug Delivery By Using Near-Real Time Sensing And Feedback, Pratik Adhikari

Doctoral Dissertations

Personalized medicine, seen as the solution to address the variability among the individuals, is the movement which proposes customization of medical procedures based on the need of the patient during the stages of prevention, diagnosis, treatment, and follow up. As the technology in medicine expands and newer methods of diagnosis and treatment are introduced in the clinic, real time data from the procedures is critical to assess the performance at point of care. Real time feedback, through collection of data at point of care would help make informed clinical decisions, potentially improving the efficacy of the treatment. In this dissertation, …

Kinetic Energy Harvesting Mechanism For Vortex Drop Structures, Mungtra Chusilp

Doctoral Dissertations

Energy recovery from wastewater is gaining significance as utilities work toward achieving energy neutrality and sustainability in their wastewater collection and treatment systems. In this dissertation, kinetic energy harvesting mechanism for vortex drop structures found within the municipal waste and storm water conveyance systems is presented. There are thousands of sewer drop structures installed across the U.S. carrying billions of gallons of sewage each year. A custom micro water turbine is developed in this research which could be retrofitted within the existing drop shafts to harvest the excessive kinetic energy available. This dissertation presents the conceptual design and analysis of …

A Non-Invasive Fluorescence-Based Oxygen Sensor And Platform For Studying Cell Responses To Metabolic Agents In Real-Time, Koutilya Reddy Buchapudi

Doctoral Dissertations

A fluorescence-based sensor in a transverse flow/stop measurement platform has been developed to determine real-time changes in oxygen consumption rates for cell metabolic studies. The oxygen sensitive fluorophore platinum octaethylporphyrin was embedded in a cellulose acetate matrix and affixed to a fiber optic bundle, which provided for transmission of the excitation and emission wavelengths of the film. The fiber optic bundle was sealed in a sensor head that can be used in standard 24-well plates common to research labs. The utility of the sensor and sensing platform were determined by measuring the changes in oxygen consumption rates of Candida albicans …