Engineering Commons^™

Incorporation Of High-K Hfo2 Thin Films In A-Igzo Thin Film Transistor Devices, Aaron Hamilton Bales

Masters Theses

In this study, HfO2 [hafnium oxide] thin films are investigated extensively as part of indium gallium zinc oxide (IGZO) thin film transistor (TFT) devices. They are incorporated into the TFTs, both as a gate insulator and a passivation layer. First, the HfO2 [hafnium oxide] films themselves are investigated through an annealing study and through I-V and C-V measurements. Then, HfO2 [hafnium oxide] is suggested as a replacement for commonly used SiO2 [silicon dioxide] gate insulator, as it has a dielectric constant that is 4 – 6 times higher. This higher dielectric constant allows for comparable TFT performance at a lower …

Ion Irradiation Characterization Studies Of Max Phase Ceramics, Daniel William Clark

Masters Theses

The family of layered carbides and nitrides known as MAX phase ceramics combine many attractive properties of both ceramics and metals due to their nanolaminate crystal structure and are promising potential candidates for application in future nuclear reactors. This thesis reports on the background, design, and analysis of an experiment focused on determining the effects of energetic heavy ion irradiations on polycrystalline samples of titanium silicon carbide 312, titanium aluminum carbide 312, and titanium aluminum carbide 211. The irradiation conditions consisted of ion doses between 10 and 30 displacements per atom at temperatures of 400 and 700 degrees Celsius, conditions …

Kinetic And Thermodynamic Modeling Of Long Term Phase Stability In Alloy 800h Subjected To Lwr Core Conditions, Wayne Ethan Pratt

Masters Theses

An in depth literature review of Incoloy Alloy 800H was conducted and presented to summarize the current understanding of microstructural evolution under irradiation and secondary phase precipitate stability. Due to a lack of radiation induced segregation (RIS) data for Alloy 800H, Isopleth sections varying Cr, Ni, Ti, and Si were generated from a computational thermodynamics approach using ThermoCalc and analyzed to compensate for knowledge related to radiation induced precipitates (RIP’s). These isopleths were analyzed for a composition range based off previous knowledge of RIS tendencies in austenitic stainless steels. Analysis of four major binary phase diagrams and complex phase diagrams …

Mixing Metals For Magic Materials: Analysis Of Binary Eutectic Alloys For Metamaterial Applications, Ethan Elder Fox

Masters Theses

Uses of metamaterials, also known as negative index materials (NIMs), are wide ranging and include lenses that have a resolution beyond the diffraction limit, incredibly small antenna, and cloaking devices for optical, infrared, and microwave wavelengths.

The unique properties of metamaterials are not found in any naturally occurring material. By having simultaneously negative values for ε [electrical permittivity] and μ [magnetic permeability], a metamaterial can have a negative index of refraction over a certain frequency band. The unique properties of negative index materials emerge chiefly from their highly ordered structure.

Binary eutectic alloys have the potential to be used as …

Computational And Experimental Studies Of Ca12al14o33, Mayenite, Elijah Duncan Barlow

Masters Theses

In this study C₁₂Al₁₄O₃₃ [mayenite] is computationally modeled, synthesized, and compared to literature in order to build a knowledge base for the further study of this compound. It is hoped that this study of mayenite will lead to the development of a new transparent conductive oxide that uses earth abundant elements instead of rare earth elements. For this study polycrystalline mayenite was synthesized using traditional solid-state synthesis techniques, and growth of a single crystal was then attempted. The VASP software package was then used to simulate the compound, both physically and electronically. The results of the simulation were then compared …

A High Pressure Cell For Spark Plasma Sintering, Justin Robert Carmichael

Masters Theses

Many nanostructured materials have been shown to have performance gains strongly dependent on the grain size in the material. Nanostructured thermoelectric materials for instance have found great performance increases through reduction of the grain sizes, due mostly to the scattering of phonons while retaining a good electrical conductivity. Other such examples abound where the grain size plays an important role in the performance of the material, including magnetic materials, proton fuel cell membranes, or simply improving the mechanical properties of a system through the Hall-Petch relationship.

A considerable amount of effort has been applied into reducing the grain size of …

Disorder In Mg1-Xnixal2o4 Spinel And Its Impact On The Response To Swift Heavy Ion Irradiation, Brandon Alexander Perlov

Masters Theses

Spinels, which are currently used in optical applications, have many proposed functions in the nuclear industry, such as a nuclear waste form due to its radiation resistance. Disordering plays a key role in the response of spinel to a wide range of irradiation conditions. The first part of this research project was on characterizing the type and degree of disorder that can be induced by chemical substitution in the magnesium nickel aluminate spinel solid solution series (Mg(1-x)Ni(x)Al2O4). Neutron total scattering has been used to characterize the structure at both the cation and anion sublattices. High-resolution pair distribution function analysis was …

Biodegradable Nano-Hybrid Polymer Composite Networks For Regulating Cellular Behavior, Charles Henley Sprague

Masters Theses

Photo-crosslinkable polymeric biomaterials have emerged in the field of biomedical research to promote tissue regeneration. For example, scaffolds that can be crosslinked and hardened in situ have been known to make suitable implant alternatives. Since injectable and photo-crosslinkable biomaterials offer the advantage of being minimally invasive, they have emerged to compete with autografts, a current highly invasive method to repair diseased tissue. A series of novel photo-crosslinkable, injectable, and biodegradable nano-hybrid polymers consisting of poly(ε-caprolactone fumarate) (PCLF) and polyhedral oligomeric silsesquioxane (POSS) has been synthesized in our laboratory via polycondensation. To engineer the material properties of the nano-hybrid networks, varied …

Oxidized Phospholipids Regulation Of The Monocyte Recruitment Parthway In Human Aortic Endothelial Cells, Piao Jian Tan

Masters Theses

Low-density lipoprotein particles in blood plasma invade the endothelium and become oxidized, creating risk of CHD associated with atherosclerosis, the main underlying condition in coronary heart disease. Oxidation products of the phospholipid 1-palmitoyl- 2-arachidonoyl-sn-glycerol-3-phosphatidylcholine (PAPC) are bioactive components of minimally oxidized LDL that stimulate endothelial cells that line the artery, leading to monocyte binding and atherosclerosis. It is hypothesized that the regulation of the monocyte recruitment pathway by these oxidized phospholipids is mediated by the binding of OxPAPC to one or more mediating proteins. Human recombinant VEGFR2, GRP78, and EP2bind to OxPNB, a biotinylated analog of OxPAPC, demonstrated using Western …

Studies Of High Temperature Hydrogen Related Damage In Welded Carbon Steel Components Used In Refineries, Maneel Bharadwaj

Masters Theses

Five materials encompassing various grades of carbon steel were received from retired and ex-service petroleum refinery equipment for root-cause evaluation of High Temperature Hydrogen Attack (HTHA) damage at UTK. These materials were submitted by three contributors: Irving Oil Refinery (IOR #1110-2), Valero (#67 & #1252134), and Phillips 66 (#555-S1 & #555-S2) on behalf of American Petroleum Institute (API). These materials originated from various flange-to-pipe welded components that were exposed in hydrogen pressure environment at elevated temperatures (> 640°F and >70 psia).

A singular crack originating at the flange inside surface just outside of the visible HAZ was observed in IOR …

Transparent Superhydrophobic Polycarbonate Coating, Gimgun Loi

Masters Theses

Superhydrophobicity is a property commonly seen in nature such as the lotus leaf. This unique property allows the surface of a material to exhibit water repellency and self-cleaning abilities. This effect is contributed by two important components: the rough surface topography and low surface free energy. Since the discovery of this unique property, several methods and various materials have been used to produce this effect and used in a wide variety of applications. However, the use of this type of effect on transparent surfaces is still being researched. I have proposed a method to develop a transparent superhydrophobic coating using …

Impact Of Fuel Rod Coatings On Reactor Performance And Safety, Ian Robert Stewart

Masters Theses

This study evaluates the use of a ceramic coating on the Zr-alloy cladding within a PWR using four ceramic compounds of 5 and 10 micron thicknesses: ZrO2, TiAlN, Ti2AlC, and Ti3AlC2. The film’s impact is assessed for variation on: reactivity, fuel cycle length, maximum temperature, film’s roughness, and transient conditions. The reactivity is analyzed using the following methods: change in the multiplication factor (k) each film introduces to the system using the ABH method, and Monte Carlo software (MCNP). Both methods are in good agreement, yielding less than half a percent change from a reference, no-film fuel pin. In order …

Determination Of Setting Times By Shear Wave Velocity Evolution In Fresh Mortar Using Bender Element Method, Jianfeng Zhu

Masters Theses

This study aims at using modified bender element (BE) method to monitor the shear wave velocity (V_s) of mortar at early-age and determine initial and final setting times with the V_s method. Modifications of the traditional BE method have been made to overcome the aggressive cementitious environment and eliminate electromagnetic coupling. BE has been successfully employed in mortar samples with and without admixtures to evaluate the evolution of V_s during the early age (first 24 hrs) of hydration. An energy approach method of determining the first arrival time of S-wave has been proposed. Pulse wave velocity …

Laser Surface And Sub-Surface Repair During Metal Additive Manufacturing, Prudvi Teja Ravi

Masters Theses

"This study examines the use of laser surface treatment to repair surface and subsurface defects. Numerical analysis was performed on laser surface melting using Gaussian heat distribution equations to analyze the depth of the melt pool created by the phenomena. Concurrently, a process map was developed with a planned set of experiments by varying the ranges of laser power and travel speed to determine the dimensions of the melt pool across the gamut. The data generated from both the process studies and the numerical analysis was then used to determine the ideal operating ranges of the process parameters to repair …

Factors Affecting The Heat Transfer During The Dip Testing Of Potential Third Generation Advanced High Strength Steels, Kramer Michael Pursell

Masters Theses

"A dip tester was designed and built at Missouri University of Science and Technology to test the effects of the primary alloying elements (Mn, Si, and Al) of Fe-Mn-Al-Si-C type 3rd generation advanced high strength steel (AHSS) alloys, dipping superheat, and dipping speed on the heat transfer during rapid solidification. The difficulties associated with casting 3rd generation AHSS were compiled as well to serve as a best-practices guide. An extensive list of potential 3rd generation AHSS alloys was developed and tested, and the effects of various dip testing parameters were examined.

Manganese was found to increase the heat flux by …

Understanding Impurities In Copper Electrometallurgy, Paul Laforest

Masters Theses

"This work involves examining two industrial reports of methods to handle impurities in copper electrowinning and electrorefining. The first part evaluates the addition of Hydrostar, Cyquest N-900, DXG-F7, and Guartec EW to copper electrowinning electrolyte to affect MnO₂ deposition on coated titanium anodes (CTAs). The second part examines the effects of anode chemistry and thiourea addition on the ductility of electrorefined copper starter sheet.

In part one, a laboratory cell was used to simulate a short cycle electrowinning cell via chronopotentiometric operation with an IrO₂-Ta₂O₅ CTA at 40⁰C. A cyclic voltammetric sweep was applied …

Hybrid Manufacturing Process Of SicF/Sic Composite Using Preceramic Polymer, Robert Raymond Meinders

Masters Theses

"Continuous fiber-reinforced silicon carbide (SiC_f/SiC) ceramic composites have been increasingly used due to their high temperature strength and graceful failure mechanisms. A disadvantage is the high cost and lengthy production processes that are required to develop these materials. Polymer infiltration and pyrolysis (PIP) is one of the most attractive fabrication processes for composites due to shape flexibility, mass production and relatively low cost; however, the quality of material obtained by this method has been considered insufficient due to the microstructure defects of the material obtained. This study investigated a hybrid of multiple polymer manufacturing processes to maximize quality …

Healing Of Bone Defects In A Rodent Calvarial Defect Model Using Strong Porous Bioactive Glass (13-93) Scaffolds, Yinan Lin

Masters Theses

"The main objective of this project was to evaluate the capacity of strong porous silicate (13-93) bioactive glass scaffolds prepared by a robocasting technique to regenerate bone and stimulate angiogenesis in a rat calvarial defect model. The scaffolds were created with the same grid-like microstructure but in a variety of formulations: (i) as-fabricated, (ii) pretreated in an aqueous phosphate solution to convert the glass surface to hydroxyapatite, (iii) loaded with bone morphogenetic protein-2 (BMP2) (1 µg per scaffold), and (iv) doped with copper (0.4-2.0 wt. % CuO). When compared to the as-fabricated scaffolds, the pretreated scaffolds enhanced bone regeneration at …

Formation And Evolution Of Spinel In Aluminum Killed Calcium Treated Linepipe Steels, Obinna Adaba

Masters Theses

"Magnesium aluminate (Spinel) inclusions have been observed to cause hook crack in line pipe steels. These inclusions are typically formed during liquid steel processing at the ladle metallurgy furnace (LMF) and subsequently modified by calcium to form less harmful liquid inclusions. Unfortunately, spinel inclusions are still sometimes observed in samples taken from the tundish and coil after calcium treatment.

The formation and evolution of spinel inclusions during liquid steel processing at two industrial mini mills was investigated by analysis of lollipop samples taken at different stages of the steelmaking process. The effect of reoxidation on the formation of spinels after …

Evaluation Of Nickel-Titanium Oxide-Niobium Pentoxide Metal Ceramic Composite As Interconnect For Solid Oxide Fuel Cell, Abhijith Budur

Masters Theses

"With increasing importance for clean energy, fuel cells have gained great significance in recent decades. Solid oxide fuel cells are easy to transport due to presence of solid electrolyte and also have requisite electrical properties,but have been obstructed by their limitation to be used at only temperatures greater than 600⁰C and less than 800⁰C. To construct a stack of cells, materials that are good electrical conductors and having necessary mechanical strengths at that temperatures are being considered as interconnects between the cells. Evaluation of Nickel-Titanium dioxide-Niobium pentoxide (NTN) as interconnect and comparison to Stainless Steel 441 alloy has been made …

Advanced Sustainable Concrete Materials For Infrastructure Applications, Kaylea Ann Smith

Masters Theses

"This study was performed to examine the effects of cement replaced by high volumes of Class C fly-ash on durability characteristics of concrete up to 120 days. Specifically, this study investigates possibility of amending American Society for Testing and Materials (ASTM) to allow High Volume Fly-ash (HVFA) concrete to cure until later ages prior to testing instead of 28 days. Five mix designs were compared with varying fly-ash percentages from 0 to 70% (by total cementitious mass). No other additives were present in any of the five mix designs. Water-to-cementitious ratio (w/cm) and total cementitious material remained constant as 0.40 …