Engineering Commons^™

A Study Of Settlement In Landfills Due To Biodegradation, Michael Guasconi

Theses

Finding new space for landfills is difficult due to land availability, stringent environmental regulations, and public sentiment. So other means of waste disposal, such as hauling it to a distant landfill, or incinerating it, will have to be resorted to. These methods may be unpopular with the public involved. By studying settlement due to biodegradation, ways to increase settlement can be found, allowing for additional waste disposal capacity in operating, and closed landfills.

Existing theoretical models are based on rheological concepts, not on biodegradation. So, they do not realistically model settlement. In this study, a model to determine the rate, …

Optimizing Rail-Truck Intermodal Drayage Operations, Wen Zhang

Theses

This thesis presents a case study of the trucking (or drayage) portion of rail-truck intermodal freight transportation. The approach used was to examine in detail the current costs and potential for improvement at one New Jersey intermodal terminal. The analysis is conducted using a mathematical programming model to find an optimal scheduling plan for the drayage operation. To solve the model more efficiently, a modification is made to explore the special structure of the original problem which has a sparse constraint matrix. The model is solved first with an objective function that minimizes the total cost of the operation, and …

Synthesis Of Boron Nitride/Vycor Composite Membrane Structures By An Optimized Lpcvd Process, Chenna Ravindranath

Theses

Since the advent of the idea of ultrafiltration, microporous membranes have come through a long way in establishing a niche as an efficient technology for gas separation applications. More and more research is aimed at reducing pore size towards nanolevels, when separation factor is the criterion rather than the permeability. This work is focused at synthesizing and characterizing microporous inorganic membranes for gas separations by molecular sieving. BN was deposited on mesoporous vycor tubes using triethylamine borane complex (TEAB) and ammonia as precursors. Effect of temperature and deposition geometry on permeability of various gases has been studied. Very high selectivities …

Low Pressure Chemical Vapor Deposition Of Tungsten As An Absorber For X-Ray Masks, Hongyu Chen

Theses

Tungsten film is one of promising materials for X-ray absorber in X-ray Lithography technology because of its high X-ray absorption and refractory properties. This study focus on CVD method to make tungsten film for X-ray absorber.

In this work, a cold wall, single wafer, Spectrum 211 CVD reactor was used for the deposition of tungsten from H, and WF6. The growth kinetics were determined as a function of temperature, pressure and flow ratio. The deposition rate of as deposited tungsten films was found to follow an Arrehnius behavior in the range of 300-500°C with an activation energy of 55.7 kJ/mol. …

Algorithms For The Njit Turbonet Parallel Computer, Nitin J. Lad

Theses

Element selection for arrays, array merging, and sorting are very frequent operations in many of today's important applications. These operations are of interest to scientific, as well as other applications where high-speed database search, merge, and sort operations are necessary and frequent. Therefore, their efficient implementation on parallel computers should be a worthwhile objective. Parallel algorithms are presented in this thesis for the implementation of these operations on the NET TurboNet system, an in-house built experimental parallel computer with TMS320C40 Digital Signal Processors interconnected in a 3-D hypercube structure. The first algorithm considered is selection. It involves finding the k-th …

Auditing & Measuring The Need For Flexibility In A Manufacturing Facility, Kartika-Sari Stroman

Theses

Flexible manufacturing was created out of the need for facilities to be able to efficiently respond to changes in their environment so as to build a competitive advantage. Flexible manufacturing (FM) is currently viewed as a way for facilities to be able to introduce and produce multiple products quickly and more efficiently. In this research we will present some new tools to help managers address the changes that are affecting the facility.

An audit was developed to help system designers identify the changes that are impacting the facilities. The audit provides the opportunity to understand the changes that are occurring …

Removal Of Vocs From Waste Gas Streams By A Hollow Fiber Permeator, Varinder Pal Malik

Theses

Removal of various VOCs from air/nitrogen feed streams using a novel hollow fiber membrane was studied. Hollow Fiber Module (HFM) used had composite silicone membranes wherein an ultrathin (~ 1μm), nonporous silicone rubber membrane layer had been plasma polymerized on a porous (porosity: 0.4) polypropylene substrate. VOCs studied were toluene, methanol, acetone, methylene chloride and hexane. Primary focus was on single VOCs, although separation of VOC mixtures was also briefly studied. HFM was found to be extremely effective in removing various VOCs from feed streams. Removal of 90-99 % of various VOCs was achieved at low feed flow rates and …

Analysis Of Cim Performance Using Different Lan Structures A Simulation Approach, Kirk Rawle

Theses

This research illustrates a systematic procedure for modeling and performance analysis of the integration effect of communication network to the physical system. The concept is to model different layouts of Computer Integration Manufacturing (CIM) using different Local Area Network(LAN) structures. The steps to accomplish this concepts are, a) To determine the performance measures for physical layouts and the communication network, in order to obtain a performance analysis. b) Modeling the physical layout using Promodel simulation package. c) Extracting results from the outcome of the simulation of the physical layout and using this as input to the communication network simulation. d) …

The Effect Of Liquid Gallium On Plastics, Vivek P. Dwivedi

Theses

As part of a joint effort by Cornell University and NJIT to find a replacement for mercury as a pressuring medium for P-V-T devices, we investigated the effect of liquid gallium on four thermoplastics: two semi-crystalline ( high density polyethylene and polypropylene ) and two amorphous ( polystyrene and polymethylmethacrylate ). Test specimens were covered with liquid gallium and held in vacuum oven at temperatures close to their melting points for up to two weeks. Change in weight after treatment with gallium was measured, along with tensile testing and particle analysis using dispersion x-ray spectroscopy. The results are compared with …

Reverse Osmosis As A Pretreatment Of Ion Exchange Equipment At Pse & G'S Hudson Generation Station, Steven Leon

Theses

Public Service Electric and Gas Company's Hudson Generating Station has historically had problems providing sufficient high quality water for its two once through, supercritical design boilers. The station requires over 60 million gallons annually to compensate for system losses.

The stations' ion exchange demineralizers proved to be costly to operate and overall inefficient in performance. Drawbacks include: short service cycles, periodic contamination of storage tanks due to premature breakthrough, prohibitively high chemical regenerant costs, excessive labor requirements, frequent resin replacement, and overall unreliable plant operations.

A reverse osmosis unit was installed as a pretreatment to the demineralizers to offset these …

Congestion Management Systems Development And Implementation : Four Case Studies, Arlene Rose-Marie Willis

Theses

To address concerns of poor air quality, congested highways and the need to manage and plan for transportation within budgetary constraints, the Intermodal Surface Transportation Efficiency Act of 1991 (ISTEA) mandated the development and implementation of a Congestion Management System (CMS). Primarily, a CMS will fuel transportation decision making with information on system performance and alternate strategies to alleviate congestion and enhance mobility. Efforts through ISTEA are expected to produce a more efficient American transportation system -- this thesis takes a look at the preparatory activities.

It is based on a federally funded project with metropolitan planning organizations (MPOs) in …

Chute Flow Experiments, Yahong Zhang

Theses

The objective of this thesis is to study the behavior of granular materials flowing down an inclined chute using three diagnostic techniques under different chute inclination angles and chute floor conditions. The three methods are: (1) tracking the motion of single particle within the mass in a noninvasive manner using a transmitting sphere and antenna receiving system, (2) scale mass flow rate measurement, and (3) high speed camera system to obtain flow velocity measurements.

For these purposes, an experimental setup has been completed and a set experiments has been performed.

Effects Of Ergonomic Worksite Changes On Risks For Cumulative Trauma Disorders Of The Upper Body In An Assembly And Press Operation Job, David B. Mahone

Theses

Cumulative trauma of the upper body is associated with a variety of individual and job factors. An effort to optimize the human-hardware interface to minimize cumulative trauma is favored. Workers in a set of jobs had complained about hand/wrist and shoulder discomfort. One job was selected for testing alternate machine controls and worksite layout. Electromyography was used to test muscle activity, and photogoniometry was used to measure posture.

For the group of ten worker-subjects, statistically significant decreases in hand/wrist and shoulder muscle activity were found. A marginal, but significant increase in neck muscle activity was also found. When one subject …

Fundamentals Of Adhesion Of Organic Compounds And Aqueous Cleaning Of Glass And Metal Surfaces : Applications In The Pharmaceutical And Chemical Industries, Michel J. De Ruijter

Theses

In this thesis we studied the physics and chemistry of the adhesion of various classes of organic compounds to glass and stainless steel surfaces, by using diagnostic aqueous cleaning solutions and other techniques. We defined the thermodynamic requirements for aqueous cleaning based on extensive experimental and theoretical work. Novel cleaning diagrams are introduced, based on electrostatic interactions between organic compounds and solid surfaces, to facilitate the design of aqueous cleaning systems. We studied the mass transfer parameters for selected situations. The electrochemical Pourbaix-diagrams were used to explain the effect of hydrogen peroxide added to aqueous solutions and to avoid corrosion …

Analysis Of A Design For Its Quality Manufacturability In Terms Of Misalignments And Fastener Related Problems, Abhinav Dhar

Theses

This study analyzes the relationship between design parameters established at the initial stage of the design process and the manufacturing quality problems that manifest themselves during production. Specifically, we study the relationship between design features and the occurrence of misalignment defects and fastener related problems.

This outcome of this work is a methodology, Design for Quality Manufacturability (DFQM). DFQM addresses the likelihood that defects will occur during the manufacture of a product in a standard plant. This is based on the premise that defects in assembled products are often influenced by some features of the design and/or assembly process. These …

A Study Of Transit Corridors Within The Njtpa Region, Mark Kagen Berger

Theses

Identifying potential bus and rail transit corridors for the North Jersey Transportation Planning Authority (NJTPA) region by examining current travel patterns of commuters was the purpose of this thesis. The current transit corridors within the NJTPA region was discussed first, followed by the methods for selecting specific municipalities for analysis. At this point, specific examinations of the selected municipalities' origin and destination travel patterns were mapped. The results were then summed up, along with a discussion of potential new bus and rail transit corridors based on trips originating along a corridor enroute to the same municipality. The final discussion examined …

A Modified Lrt-Based Spread-Spectrum Receiver Using Spatial And Temporal Processing, Jeffrey L. Cutcher

Theses

The problem of demodulating a direct-sequence (DS) spread-spectrum signal in the presence of single-tone or narrow-band interference and multi-path is discussed. A likelihood-ratio test (LRT) receiver is presented which consists of a whitening filter and a RAKE correlator.

A modified LRT receiver structure is then considered where the whitening filter is replaced by an antenna array with corresponding tap coefficients. The array spatially removes the interference by estimating it's angle-of-arrival. Using the array has an advantage over the original LRT receiver when a narrow-band interference is present. Both receivers are identical in performance under the single-tone interference model.

A third …

Hydrodynamic And Water Quality Modeling Of The Whippany River, John E. Krohn

Theses

The Whippany River is located in northern New Jersey and is a major tributary to the Passaic River System. This waterway accepts a wide variety of wastes from the diverse communities within its watershed. These wastes contribute to a rather complex network of biological, chemical and physical interactions.

The purpose of this study is to develop a water quality model using QUAL2E. This model will be used as a tool to simulate the complex interactions that take place within the river system. The river must he considered from physical, biological and chemical perspectives. A successful model can determine current water …

Effect Of Fiber-Matrix Coupling On The Mechanical Properties Of A Totally Bioabsorbable Composite, Barbaro Jesus Perez

Theses

The mechanical properties of a new class of bioabsorbable polymer-composite based on the amino acid tyrosine and calcium phosphate fibers were studied. The effect of the fiber aspect ratio on the elastic modulus of a discontinuous fiber composite was analyzed using the SMC composite micromechanics computer model. The mechanical stiffness of this polymer was found to be superior to that of poly-p-dioxanone, caprolactone and poly-o-ester.

The fiber surface was modified with methane plasma spray to improve the fiber-matrix coupling. The treated fiber composites had 16-40% higher tensile modulus than the untreated fiber composites. From the flexural test results it is …

Integration Of Pneumatic Fracturing And In Situ Vitrification In Coarse Grained Soils, Sean Thomas Mcgonigal

Theses

This thesis investigates conceptual integration of the Pneumatic Fracturing (PF) process with In Situ Vitrification (ISV) for remediation of contaminated soil. Integration will permit ISV melts to be initiated below the ground surface and extend the depth of the ISV process.

Bench scale experiments were conducted in 4.9 ft³ (0.14 m³) Plexiglas tanks filled with a test soil that was specifically blended to simulate the Hanford Formation in Richland, WA. Discrete pneumatic fractures were successfully created and filled with the ISV starter path material. Conductivity measurements made across two graphite electrodes exhibited a pre-fracture soil resistance of …

Application Of Signal Processing Techniques For Measurement Of Muscle Fiber Conduction Velocity, Satheesh Kumar Swaminathan

Theses

The objectives of this study were to evaluate if muscle fiber conduction velocity (MFCV) could be used as a reliable indicator of fatigue and to characterize the recovery of MFCV after a fatiguing contraction. The decline of MFCV with fatigue was modelled using linear regression and compared with the decline in median frequency (MF). It was found that the percent decline in MF with fatigue was greater than that of MFCV with fatigue and that the decline of MFCV was consistent in all subjects tested. It was thus determined that MFCV could be used as a reliable indicator of fatigue. …

The Morphology Of Uhmwpe Wear Debris Generated By A Hip Joint Simulator, Aaron P. Essner

Theses

The size, quantity and shape of total hip replacement wear debris may identify wear mechanisms as well as play a role in osteolysis. Characterization of wear particles generated from a hip joint simulator was conducted followed by comparison with literature reported in vivo results. The effect of counterface material and lubricant type on particle morphology was assessed. Biomaterial pairs including UHMWPE articulated against CoCr, Alumina and Zirconia were considered. Deionized (D.I.) water and bovine serum were used as lubricants. Particles generated from Alumina/UHMWPE in serum were slightly larger than those for CoCr and Zirconia against UHMWPE in serum. Particle shape …

Reducing Rail-Truck Freight Intermodal Drayage Costs, David Moy Jr.

Theses

In rail-truck intermodal transport, a highway truck-trailer or container is moved by truck from a shipper to a rail terminal in the shipper's vicinity, and by rail in line haul between rail terminals. Upon being unloaded at the destination rail terminal, the container is delivered to a receiver (consignee) by truck. The highway portion of the move, or drayage, accounts for a relatively high percentage of total origin to destination cost, and it limits severely the competitiveness of intermodal service with door-to-door truck service. The approach used in this thesis is to examine in detail the current costs and potential …

Radiation Damage Studies In Gate Oxides, Sandeep G. Bharathi

Theses

Detailed investigation of the effects of Gamma-ray irradiation on the electrical properties such as current-voltage arid capacitance-voltage characteristics in thermally grown SiO₂ films in the thickness range of 15 to 120 nm on silicon substrates is presented in this thesis. The structures used in this study are Al/Poly/SiO₂/Si/Al and Al/SiO₂/Si/Al MOS capacitors. Based on the electrical characterization studies, we observe that irradiation causes generation of positive charges in the oxide leading to a shift of the high frequency Capacitance-Voltage (C-V) curves. An increase in surface state density at the SiO₂-Si interface with increase …

Modeling The Fate Of Volatile Organic Compounds In Wastewater Treatment Facilities; Implementation Of Volatilization Models In Envirocad, Vinita Chhahira

Theses

The 1990 Clean Air Act Amendments have identified wastewater treatment facilities as a major source of volatile organic compound (VOC) emissions. VOCs present in wastewater discharges affect the quality of receiving waters, while emissions to the air affect downwind populations. The primary mechanisms involved in VOC removal from a wastewater treatment facility are volatilization and stripping, biodegradation, and sorption to either suspended or biological solids. Although many models have been developed to predict the fate of VOCs in wastewater treatment facilities, no model completely predicts emissions for an entire wastewater treatment facility. The focus of this work is to incorporate …

A Defect Detection Algorithm For Sequential And Parallel Computers, Ralf Hross

Theses

The comparison of images containing a single object of interest, where one of them contains a model object, is frequently used for defect detection/identification. This is often a problem of interest to industrial applications. To make this task more efficient, the implementation on parallel computers should be a major objective. This thesis introduces sequential and parallel versions of an algorithm that compares original(reference) and processed images in the time and frequency domains. The emphasis is on parallel implementation. This comparison may help to detect changes in images. Extracted data is also compared to database data in an attempt to pinpoint …

A Comparison Of Anhydrous Ethanol Production From Ethylene And From Corn Utilizing Life Cycle Analysis Methodology, Gregory Morse

Theses

There is currently much concern with the impact on the environment due to industrial processes. One method to assess this impact is to perform a Life Cycle Analysis (LCA) on the process. Life Cycle Analysis is made up of three stages; Life Cycle Inventory Analysis, Life Cycle Impact Assessment, and Life Cycle Improvement Assessment. In this study, Life Cycle Inventory Analysis methodology was applied to two industrial processes for producing anhydrous ethanol. The first process is the fermentation of corn, and the second is the hydration of ethylene using water and a catalyst. Each process was first modeled using the …

Low Pressure Chemical Vapor Deposition Of Silicon Nitride Films From Tridimethylaminosilane, Xin Lin

Theses

In this study amorphous stoichiometric silicon nitride films were synthesized by low pressure chemical vapor deposition (LPCVD) using tri(dimethylamino) silane (TDMAS) and ammonia (NH₃). The growth kinetics were determined as a function of temperature in the range of 650 - 900 °C, total pressure in the range of 0.15 - 0.60 Torr, and NH₃/TDMAS flow ratio in the range of 0 - 10. At constant condition of pressure (0.5 Torr), TDMSA flow rate (10 sccm) and NH₃ flow rate (100 sccm), the deposition rate of as-deposited silicon nitride films was found to follow an Arrehnius …

The Photolithographic Patterning Of Porous Silicon Using Silicon Nitride And Silicon Carbide Films As Masks, Hong Wang

Theses

In this study, a simple photolithographic pattern process for porous silicon is described. The process utilizes silicon nitride or silicon carbide coated on the top of silicon wafer as a masks. Then a test pattern was projected on the sample by illumination during anodic etching in HF:ethanol solution which produced microcracks in regions illuminated during anodization. Creation of these microcracks resulted in formation of porous silicon in the underlying regions. The cracking is related to the stress in the thin film. The films with tensile stress exhibit cracking while compressive stress samples do not. Compared to silicon carbide films, silicon …

Am/Fm Digital Audio Broadcasting In-Band On-Channel Transmission, Michael Meyer

Theses

This thesis examines the in-band on-channel transmission of digital audio data for application in Digital Audio Broadcasting (DAB). The premise is to use the existing FM channels for transmission of DAB. For the FM channel used for analog audio transmission, two different scenarios are suggested and investigated.

In the first scenario, to enable overlay of the new DAB and current FM transmissions, the digital data is modulated by a direct sequence spread spectrum signal to bring the average transmitted power below that of the FM signal using the same channel. The FM signal interferes with the digital transmission and it …