Engineering Commons^™

Fatigue Response Of Cracked Aluminum Panel With Partially Bonded Composite Patch, Jason J. Denney

Theses and Dissertations

More and more aircraft, both commercial and military, are being called upon to fly well beyond their economic and structural service lives. Budget cuts and dwindling new aircraft development has forced the United States Air Force (USAF) to look toward more reliable structural repairs. One of these repair techniques, which was the subject of this study, is the repair of metallic aircraft structures using high strength composite materials. This study investigated the fatigue response of a precracked, 508x1 52x1 mm, 2024-T3 aluminum panel repaired with a partially bonded, unidirectional, three-ply boron/epoxy composite reinforcement with ply lengths of 68, 56 and …

Thermo-Mechanical Fatigue Behavior Of Cross-Ply Ceramic Matrix Composite Under Tension-Tension Loading, Dana G. Allen

Theses and Dissertations

The purpose of this study was to investigate the combined effect of cyclic temperature and loading on the fatigue life of a ceramic matrix composite with a cross ply lay-up. The material used in this study was a potassium borosilicate glass (BSG) doped magnesium aluminosilicate (MAS) cordierite matrix reinforced with Nicalon (silicon carbide, SiC) fibers in a [0/90]_4s lay-up. Thermomechanical fatigue (TMF) tests were performed with a period of 180 seconds/cycle, or 0.00556 Hz, and a triangular wave-form. The temperature was cycled between 566°C and l093°C, and the stress levels varied between 60 MPa and 145 MPa. All tests …

Thermal Stresses In End-Heated Layered Media, Jerry R. Couick

Theses and Dissertations

Thermal stresses in semi-infinite layered beams heated on the end are calculated using an extension to simple bimetallic thermostat theory. Recently, researchers have used the concept of interfacial compliance to determine interlaminar stresses in a simple thermostat of finite length subjected to a uniform temperature increase. In the present work, the thermostat theory is extended to apply to the beams of interest. A closed-form solution to the problem is obtained. It is not applicable within about one beam thickness (St Venant boundary region) of the end. Various classes of layered materials are analyzed to determine if significant stresses exist outside …

Investigation Of Residual Strength And Fatigue Life Of Unstiffened Aluminum Panels With Multiple Site Damage, Mark C. Cherry

Theses and Dissertations

Multiple Site Damage MSD is the occurrence of small fatigue cracks at several sites within aircraft structures. This is important since it may lower the residual strength and fatigue life of the structure beyond what can be predicted using the damage tolerance technique based on a single crack, currently in use to design aircraft structures. This study investigated the effects of MSD on unstiffined panels. MSD usually occurs at rivet holes, or other stress concentration locations within an aircraft structure. This study simulated rivet holes with MSD, by using holes of constant diameter with small cracks, evenly spaced across the …

Synthesis Of Boron Nitride/Vycor Composite Membrane Structures By An Optimized Lpcvd Process, Chenna Ravindranath

Theses

Since the advent of the idea of ultrafiltration, microporous membranes have come through a long way in establishing a niche as an efficient technology for gas separation applications. More and more research is aimed at reducing pore size towards nanolevels, when separation factor is the criterion rather than the permeability. This work is focused at synthesizing and characterizing microporous inorganic membranes for gas separations by molecular sieving. BN was deposited on mesoporous vycor tubes using triethylamine borane complex (TEAB) and ammonia as precursors. Effect of temperature and deposition geometry on permeability of various gases has been studied. Very high selectivities …

Low Pressure Chemical Vapor Deposition Of Tungsten As An Absorber For X-Ray Masks, Hongyu Chen

Theses

Tungsten film is one of promising materials for X-ray absorber in X-ray Lithography technology because of its high X-ray absorption and refractory properties. This study focus on CVD method to make tungsten film for X-ray absorber.

In this work, a cold wall, single wafer, Spectrum 211 CVD reactor was used for the deposition of tungsten from H, and WF6. The growth kinetics were determined as a function of temperature, pressure and flow ratio. The deposition rate of as deposited tungsten films was found to follow an Arrehnius behavior in the range of 300-500°C with an activation energy of 55.7 kJ/mol. …

Estimation Of Internal Forces And Moments In Linearly Vibrating Beam Structures, Doris Yasmou Yacoub

Archived Theses and Dissertations

No abstract provided.

Nonlinear Geometric And Material Behavior Of Composite Shells With Large Strains, Scott A. Schimmels

Theses and Dissertations

A two-dimensional, geometrically and materially nonlinear shell theory applicable to arbitrary geometries described by orthogonal curvilinear coordinates and encompassing large displacements, moderate rotations for large strain situations has been developed. Additionally, the theory includes Jacobian transformation matrices, based upon displacement parameters, for the Cauchy - 2nd Piola-Kirchhoff stress-state and the Cauchy (Almansi) - Green strain-state transformations, and a layered material approach is included for the elastoplastic analysis to allow for variation of plasticity through-the-thickness. Doubly curved 20, 28, and 36 degree-of-freedom finite elements are defined based on specialization of the theory to spherical coordinates. The computer program includes algorithms for …

The Photolithographic Patterning Of Porous Silicon Using Silicon Nitride And Silicon Carbide Films As Masks, Hong Wang

Theses

In this study, a simple photolithographic pattern process for porous silicon is described. The process utilizes silicon nitride or silicon carbide coated on the top of silicon wafer as a masks. Then a test pattern was projected on the sample by illumination during anodic etching in HF:ethanol solution which produced microcracks in regions illuminated during anodization. Creation of these microcracks resulted in formation of porous silicon in the underlying regions. The cracking is related to the stress in the thin film. The films with tensile stress exhibit cracking while compressive stress samples do not. Compared to silicon carbide films, silicon …

Aeration And Operation Of An Immobilized Cell Oxidative Bioreactor, James Joseph Woods

Theses

The primary purpose of this work is to help define the optimum window of operations for an immobilized cell oxidative bioreactor. The analytical technique employed requires no outside verification (such as G.C. analysis) and is independent of liquid flow rate. Method of aeration has been determined to be an important parameter for optimizing bioreactor efficiency, and optimization of the quantity of hydrogen peroxide added to provide oxygen during bio-oxidation has been investigated. Ammonium hydroxide as a fixed nitrogen source can be used to restore the vitality of the bioreactor under certain conditions.

The effects of several different methods of providing …

Low Pressure Chemical Vapor Deposition Of Copper Films From Cu(I)(Hfac)(Tmvs), Wei-Shang King

Theses

Recently, copper has been found as a possible substitute for Al alloys because of its low resistivity (1.67 μΩ • cm) and potentially improved resistance to electromigration. Conventional physical vapor deposition (PVD) method do not provide the conformal deposition profile for the high density integrated circuit, therefore, chemical vapor deposition (CVD) has become the most promising method for the resulting conformal profile.

In this work, a cold wall, single wafer, CVD tungsten reactor was used for the deposition of copper with Cu(I)(hfac)(tmvs). Film growth rates were between 100 to 800 A/min depending on processing conditions, and an Arrhenius type activation …

Synthesis Of Silicon Oxide/Vycor Composite Membrane Structures By An Optimized Lpcvd Process, Abhijit Datta

Theses

This study is focused on development of highly selective ceramic membrane structures consisting of silicon dioxide films synthesized by low pressure chemical vapor deposition (LPCVD) on mesoporous Vycor substrates. The ability of easily altering the composition of such films by varying the LPCVD processing parameters affords the opportunity of microengineering the pore structure by reducing the diameters of pre-existing pores in the support. The process parameters investigated include, deposition temperature, total pressure, and flow rate of oxygen. Both the kinetics and select properties of the deposits were examined. The growth rate as a function of temperature was seen to follow …

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

Eigenproperties Of Nonclassically Damped Dynamic Systems, Daniel Patrick Malone

Masters Theses

"This thesis develops perturbation series solutions for the eigenvalues and eigenvectors of nonclassically damped dynamic systems for the case where the unperturbed system has repeated eigenvalues. The case of repeated eigenvalues is much more complicated than the case of perturbing a system with distinct eigenvalues. Because of this difficulty, only a specific category of dynamic systems with repeated eigenvalues is addressed. Namely, only those systems that when perturbed have series solutions of the form of a power series. This category of systems can be easily identified by an a priori check developed in the application section of this thesis. The …