Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Theses/Dissertations

Master's Theses (2009 -)

Chemical Engineering

Articles 1 - 8 of 8

Full-Text Articles in Engineering

Characterization And Evaluation Of Cordless Nailer Performance For Liquid And Gaseous Fuels, Mark Carioscio Oct 2018

Characterization And Evaluation Of Cordless Nailer Performance For Liquid And Gaseous Fuels, Mark Carioscio

Master's Theses (2009 -)

The Paslode Cordless XP Framing Nailer is a combustion-powered nail gun that operates using a fuel blend of a propylene and 1-butene. This tool is designed to drive nails using a piston driven by a combustion reaction. The current fuel blend is able to fire approximately 1200 shots per fuel cartridge and match the energy output of pneumatic, corded nailers on the market. This thesis is written with the intent to gain a better understanding of the operation of the tool and how its performance varies when the fuel source is altered. A bizonal combustion model was created to simulate …

Go to article

Comparative Study Of Different Sensor Array Designs Involving Plasticized Polymer Coatings For Btex Detection In Water, Nicholas Post Jul 2018

Comparative Study Of Different Sensor Array Designs Involving Plasticized Polymer Coatings For Btex Detection In Water, Nicholas Post

Master's Theses (2009 -)

Detection and quantification of benzene, toluene, ethylbenzene, and xylenes (BTEX) in liquid phase is of interest because of the significant public health hazards posed by these compounds. BTEX are volatile organic compounds (VOCs) commonly used as additives in gasoline. Shear horizontal surface acoustic wave (SH-SAW) devices have shown promise in liquid phase sensing applications and is used to address this problem. SH-SAW devices can be made chemically sensitive by depositing a polymer coating on the device surface. SH-SAW devices coated with commercially available polymers have shown modest sensitivity to BTEX compounds. However, there are few polymers which exhibit the properties …

Go to article

Evaluating The Bond Behavior Between Frp And Grooved Concrete Specimens Using Single Shear Pull Out Test, John Omboko Apr 2017

Evaluating The Bond Behavior Between Frp And Grooved Concrete Specimens Using Single Shear Pull Out Test, John Omboko

Master's Theses (2009 -)

Surface preparation affects the bond behavior between Fiber Reinforcing Polymer (FRP) composite material and concrete. In this research, a special type of surface preparation known as grooving, which involves cutting transverse grooves, is conducted on concrete blocks (specimens) that are categorized as either Unfilled (U) or Filled (F). This idea is to ascertain how the grooves affect the strength of FRP-bonded-concrete specimen. These two categories are then benchmarked to control (C) specimens which do not have grooves on them. Category U specimens only have the epoxy applied on the concrete surface while category F specimens have epoxy applied on both …

Go to article

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li Oct 2016

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Go to article

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari Oct 2016

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Go to article

Investigation Of The Use Of A Plasticizer-Polymer Sensor Coating With Improved Long-Term Stability In The Liquid Phase, Laura Jeanne Alderson Apr 2016

Investigation Of The Use Of A Plasticizer-Polymer Sensor Coating With Improved Long-Term Stability In The Liquid Phase, Laura Jeanne Alderson

Master's Theses (2009 -)

Benzene is one of the volatile organic compounds present in crude oil and gasoline. Leakage from underground storage tanks or hazardous waste sites can introduce benzene contamination into nearby groundwater. Benzene is a known carcinogen and its exposure is limited by the Environmental Protection Agency to 5 parts per billion (ppb) in drinking water. Early, accurate detection of the presence of benzene contamination in groundwater supplies is extremely important. Shear horizontal surface acoustic wave (SH-SAW) devices with a chemically sensitive coating can be used for the detection of volatile organic compounds in liquid, such as BTEX (benzene, toluene, ethylbenzene and …

Go to article

Development Of A Rapid Compression Controlled-Expansion Machine For Chemical Ignition Studies, John Neuman Apr 2015

Development Of A Rapid Compression Controlled-Expansion Machine For Chemical Ignition Studies, John Neuman

Master's Theses (2009 -)

The ability to accurately model fuel combustion processes is essential to the development of transportation, power generation, and manufacturing technology. Models describing the kinetics of chemical oxidation are readily available and highly refined for a wide range of test fuels. However, these models still suffer from high levels of uncertainty under engine-relevant conditions, largely due to a lack of consistency between published validation data. An experimental testing apparatus, known as the Rapid Compression Controlled-Expansion Machine (RCCEM) has been designed and fabricated to conduct chemical kinetic studies. The RCCEM features a pneumatically-driven, custom-designed cam, which governs the volumetric compression and expansion …

Go to article

Characterization Of Plasticizer-Polymer Coatings For The Detection Of Benzene In Water Using Sh-Saw Devices, Jude Coompson Apr 2015

Characterization Of Plasticizer-Polymer Coatings For The Detection Of Benzene In Water Using Sh-Saw Devices, Jude Coompson

Master's Theses (2009 -)

Benzene is a constituent component of crude oil that has been classified as a carcinogen by the EPA with a maximum contamination level (MCL) of 5ppb in drinking water. However, of the aromatic compounds, benzene has one of the lowest polymer-water partition coefficients using commercially available polymers as sensor coatings, resulting in poor limits of detection. This work investigates new coating materials based on polymer/plasticizer mixtures coated onto a shear horizontal surface acoustic wave (SH-SAW) sensor to detect benzene in water. There are many polymers which are unavailable for use as a sensing polymer due to their glassy nature. The …

Go to article