Open Access. Powered by Scholars. Published by Universities.®
- Discipline
-
- Aerospace Engineering (24)
- Structures and Materials (7)
- Materials Science and Engineering (6)
- Engineering Science and Materials (3)
- Industrial Technology (3)
-
- Manufacturing (3)
- Mechanical Engineering (3)
- Operations Research, Systems Engineering and Industrial Engineering (3)
- Propulsion and Power (3)
- Aeronautical Vehicles (2)
- Civil and Environmental Engineering (2)
- Construction Engineering and Management (2)
- Space Vehicles (2)
- Aviation (1)
- Business (1)
- Maintenance Technology (1)
- Mechanics of Materials (1)
- Operations and Supply Chain Management (1)
- Other Materials Science and Engineering (1)
Articles 1 - 30 of 30
Full-Text Articles in Engineering
Mechanical Properties And Tension-Tension Fatigue Behavior Of A Novel Additively Manufactured Polymer Matrix Composite At Room And Elevated Temperature, Grayson M. Harber
Mechanical Properties And Tension-Tension Fatigue Behavior Of A Novel Additively Manufactured Polymer Matrix Composite At Room And Elevated Temperature, Grayson M. Harber
Theses and Dissertations
The tension-tension fatigue behavior of a novel additively manufactured AM carbon fiber reinforced polymer matrix composite was studied. This novel material system consists of T1100 carbon fibers, and a UV photocured resin developed by Continuous Composites and Sartomer. Tensile properties and tension-tension fatigue were investigated for the 090 fiber orientation as well as for the ±45 fiber orientation. Specimens with 0/90 fiber orientation were tested at ambient laboratory temperature 23 °C and at elevated temperature 150 °C, while the specimens with the ±45 fiber orientation were tested only at ambient laboratory temperature. Tension-tension fatigue testing was carried out with a …
Finite Fatigue Life Prediction Of Additively Manufactured Aircraft Engine Turbine Blade With Respect To Internal Defect Size And Location, Daniel G. Miller
Finite Fatigue Life Prediction Of Additively Manufactured Aircraft Engine Turbine Blade With Respect To Internal Defect Size And Location, Daniel G. Miller
Theses and Dissertations
Current fatigue life modeling techniques with respect to defects emphasize the dependence on the defect size with respect to fatigue life, but does not account for the effects of where a defect might be located. This research outlines a process to include defect location into the model analysis for a more precise prediction of the number of cycles to failure and where the finial failure could occur within a component. The focus is on a turbine blade structure using IN718 subjected to a pure vibratory load. The basic model predicts component life using a stress map from the frequency analysis …
Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin
Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin
Theses and Dissertations
This research considered additive manufactured (AM) molybdenum (Mo) and the effect of three variables on microstructure, mechanical properties, and the relationship between the two. Test temperature, laser speed, and shield gas or build atmosphere were varied, and samples tested and analyzed using a three-point bending test, chemical composition, and optical and scanning electron microscopy. The relationship among variables and results using a Design of Experiments was limited compared to the inclusion of every tested sample. Most effects were expected: samples tested at room temperature were brittle without statistical significance; increasing laser speed resulted in decreased ductility and strain, smaller grain …
Performance Study Of Post-Processed Additively Manufactured Low Thrust Nozzles, Tyler W. Gerhold
Performance Study Of Post-Processed Additively Manufactured Low Thrust Nozzles, Tyler W. Gerhold
Theses and Dissertations
This research explores metal post-processing techniques to effectively reduce the large anomalous protrusions found in small additively manufactured low thrust rocket nozzles. Research has found that nozzles of this kind can experience losses in thrust of over 40%. Analytic theory of adiabatic nozzle flow with viscous losses for additively manufactured nozzles does not align with what has been found when tested experimentally. Compressible flow losses, such as shock wave formation inside the nozzle diverging cone, are likely the leading causes of such loss. Reduction in nozzle irregularities can likely yield results seen in analytic theory with similar performance to traditional …
Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya
Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya
Theses and Dissertations
The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …
Potential Solution To Meet Growing Demands Of Refractory Metal: Selective Laser Melting Of Molybdenum-Tungsten Alloy, Jae Yu
Theses and Dissertations
Selective laser melting (SLM) of refractory metals has been of high interest in research due to the metals’ potential desirable characteristics in aeronautical and space applications. In particular, molybdenum and tungsten have been the focus of several studies in the search for high temperature and high strength purposes in applications like supersonic aircraft, re-entry vehicles, nuclear fission, power generation, and other space systems. However, there is still a significant knowledge gap to process defect-free alloys and making use of them in practical engineering functions. The aim of this study is to characterize the relationship between the microstructure and mechanical properties …
Critical Evaluation Of Construction Industry-Related Additive Manufacturing Research: A Scientometric Analysis, Tyler J. Brunjes
Critical Evaluation Of Construction Industry-Related Additive Manufacturing Research: A Scientometric Analysis, Tyler J. Brunjes
Theses and Dissertations
Review of construction-related AM literature is used to identify the advantages, challenges, and current trends of the research. Using a scientometric analysis of 522 bibliographic records, this research systematically analyzed construction related AM research to determine the key research areas and trends. Results showed that starting in 2015, the field has been growing at an exponential rate. Recent AM research focused on materials and reinforcement topics, which matched the most notable challenges of AM, which are material rheology, reinforcement, and lacking construction standards. This study provides an insight into AM research and identifies areas requiring more innovation before its commercial …
Design And Testing Of A Composite Compressor Rotor, Mauro Noel V. De Leon
Design And Testing Of A Composite Compressor Rotor, Mauro Noel V. De Leon
Theses and Dissertations
Additive manufacturing (AM) and molding are manufacturing methods known for building representations or replicas of conceptualized engine components, but was considered impractical for manufacturing operating engine components. More recent technology has rendered composite materials (combining high-temperature polymers and fiber reinforcement) capable of withstanding the temperature and structural requirements to compete with conventional turbomachinery metals. This study explores the application of several high-temperature polymers (ULTEM 9085, Onyx-Carbon fiber, and Epoxy-Carbon fiber) and their survivability in the operating conditions of a P400 Engine compressor. The tests conducted for this study determined their viability as compressor materials. This study required conducting tensile specimen …
Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen
Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen
Theses and Dissertations
Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …
Evaluation Of Additively Manufactured Lattices Under High Strain Rate Impact, Derek G. Spear
Evaluation Of Additively Manufactured Lattices Under High Strain Rate Impact, Derek G. Spear
Theses and Dissertations
Several additively manufactured lattice designs and configurations were evaluated under compression loads under various strain rates from quasi-static to highly dynamic. These experiments examined how the mechanical behavior of the lattice changed based on the lattice design properties and the applied strain rates. The modulus of elasticity, yield strength, plateau stress, and toughness were observed to decrease with an increase in strain rate, revealing that the lattice designs exhibit a negative strain rate sensitivity. A new lattice flow stress model was developed to account for the mechanical response of the lattice and was incorporated into a computational model for simulation. …
A Reduced Order Model Of The Celestial Icosahedron As The Substructure For A Lighter Than Air Vehicle, Torin C. Quick
A Reduced Order Model Of The Celestial Icosahedron As The Substructure For A Lighter Than Air Vehicle, Torin C. Quick
Theses and Dissertations
A finite element approach was used to investigate a novel reduced order model to determine the minimum structure dimensionality to support vacuum for a VLTAV. This modeling technique represented the individual segments of the substructure as curved beams with clamped radially-resisted boundary conditions. The full structure was then modeled as a bare structure and structure with skin to validate the results of the reduced order model. The beam geometry for the material Ultem 9085 was determined through this process leading to the 3-D printing of the structure. It was then experimentally tested under uniaxial compression complimented with a FEA model.
Improving Manufacturability And Reducing Cracking In Additively Manufactured Tungsten Alloys, Christopher P. Fassio
Improving Manufacturability And Reducing Cracking In Additively Manufactured Tungsten Alloys, Christopher P. Fassio
Theses and Dissertations
Additively Manufactured tungsten suffers from low () densities due to high concentrations of microcracks as the printed layers cool past tungsten's high ductile to brittle transition temperature. In this study, tungsten-rhenium and tungsten rhenium hafnium carbide compositions were evaluated on density and tensile strength. In addition to varying the compositions of each alloy, printing parameters and post-processing methods were also compared. Print parameters varied for all compositions on an MLab 200R C using included the laser scan strategy, hatch spacing, scan speed, laser power, and print bed material. Post processing techniques of the WRe compositions included hot isostatic pressing and …
Analysis For Hybrid Rocket Fuel Regression Using Stereolithographic Geometry, Michael P. King
Analysis For Hybrid Rocket Fuel Regression Using Stereolithographic Geometry, Michael P. King
Theses and Dissertations
Hybrid Rocket Engines (HRE) have characteristically low fuel regression that limits their performance. Additive manufacturing and rapid prototyping can possibly solve some of the problems with Hybrid propulsion regression by creating geometry not possible with conventional manufacturing. This work is attempting to make geometric regression simulation of HRE easier by using STereoLithography (STL files) as the geometry. This analysis sets flow conditions, boundary conditions, propellant selection, and allows for fuel geometry to be altered to simulate geometry’s effects on regression rate and propellant performance. This model can be used for more advanced geometric analysis to improve and predict performance.
3d Printing For Solving Part Obscolescence, Ayman G. Alqarni
3d Printing For Solving Part Obscolescence, Ayman G. Alqarni
Theses and Dissertations
The purpose of this research was to highlight the issue of parts obsolescence and to highlight the possibility of using alternative methods to overcome parts shortage. Specifically, this thesis sought to answer the research question: is the three-dimensional printing technology (3D) an applicable approach to overcome part obsolescence. The research question was answered through data research and survey analysis. Notwithstanding, the diminished manufacturing sources and material shortages (DMSMS) management and other existing approaches, such as forecasting, contracting, and reverse engineering (RE), were discussed briefly in the literature review and profoundly in chapter IV to differentiate among applicable existing solutions toward …
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Theses and Dissertations
Additive manufacturing is revolutionizing industries ranging from medicine to space. However, the structural characteristics of plastic parts created by these methods are not as well understood as their more established counterparts. This research explored two relevant areas: how the structural characteristics of ULTEM 9085 plastic behaved after exposure to orbital conditions and the design of the cross-sectional area of a beam to be 3-D printed in microgravity based on the expected loads from the printer. To study orbital effects, ULTEM 9085 was printed into 1/4th scale ASTM D638- 14 dogbones using a Stratasys 450mc printer. These dogbones were placed in …
Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin
Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin
Theses and Dissertations
The push for low cost and higher performance/efficient turbine engines have introduced a new demand for novel technologies to improve robustness to vibrations resulting in High Cycle Fatigue (HCF). There have been many proposed solutions to this, some passive and some active. With the advent of Additive Manufacturing (AM), new damping techniques can now be incorporated directly into the design and manufacture process to suppress the vibrations that create HCF. In this study, this novel unfused pocket damping technology is applied to a blade structure and the resulting damping effectiveness is quantified. The application of this technology to complex geometries …
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Theses and Dissertations
The nickel-based superalloy Inconel 718 (IN718) is an excellent candidate among aerospace alloys for laser powder-bed fusion (LPBF) manufacturing. As-built LPBF IN718 has a vertically aligned columnar (001) microstructure which translates into orthotropic mechanical behavior. The post-process heat treatments for IN718 were developed 60 years ago for wrought and cast processes and do not mitigate the columnar microstructure of the LPBF process. Recrystallization is required to remove the columnar microstructure, which would allow for parts to be fabricated on different machines or in different orientations but still achieve the same properties. This research investigated the microstructure of LPBF IN718 as …
Analysis Of Additively Manufactured Rings Under Compression Loading For Use In A Vacuum Lighter Than Air Vehicle Structure, Kevin D. Greenoe
Analysis Of Additively Manufactured Rings Under Compression Loading For Use In A Vacuum Lighter Than Air Vehicle Structure, Kevin D. Greenoe
Theses and Dissertations
A Vacuum Lighter Than Air Vehicle (VLTAV) utilizes a lightweight structure paired with an internal vacuum to achieve buoyancy; this allows it to float through-out a given atmosphere. The pressure differential between the internal vacuum andexternal atmosphere places the vehicle under intense loading. A specific structure under investigation is the celestial icosahedron, which features nine intersecting rings that have an outer diameter of 0.2032m and circular cross-sectionalthickness of 5.08mm.The celestials rings are positioned in three different orientations and are analyzed both experimentally and analytically.
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Theses and Dissertations
The three objectives of this research were to: 1.) design, build, and test AM compressors to substitute into COTS micro-gas turbine engines, 2.) provide initial correlations between FEA and compressor failure speed, and 3.) characterize the effects of AM on compressor performance. These goals improved the design cycle cost and the design-validation time cycle. ULTEM 9085, 300-AMB, and Onyx-Kevlar temperature-dependent tensile properties were measured. FEA-predicted failure speeds of stock compressor designs led design improvements, potentially fulfilling the original compressor requirements. Physical testing of the stock and ULTEM 9085 compressors occurred. Comparing these compressors' performances demonstrated that low cost, AM materials …
An Analysis Of The Viability Of 3d-Printed Construction As An Alternative To Conventional Construction Methods In The Expeditionary Environment, Jeneé A. Jagoda
An Analysis Of The Viability Of 3d-Printed Construction As An Alternative To Conventional Construction Methods In The Expeditionary Environment, Jeneé A. Jagoda
Theses and Dissertations
Conventional construction is believed by some to have reached its technological limit of performance, making it increasingly difficult for conventional construction methods to meet the U.S. military’s core standards of quality, cost, and timeliness in the expeditionary environment. While still in its infancy, 3D-printed construction has the potential to revolutionize the way the military performs construction in deployed environments. This research conducts a systematic review of the viability of 3D-printed construction to investigate whether or not it is now or could be a viable replacement for conventional construction methods, specifically in remote environments where conventional construction capability may be limited. …
Application Of Metamaterials For Multifunctional Satellite Bus Enabled Via Additive Manufacturing, Michael A. Macchia
Application Of Metamaterials For Multifunctional Satellite Bus Enabled Via Additive Manufacturing, Michael A. Macchia
Theses and Dissertations
Space systems require materials with superior stiffness to weight ratios to provide structural integrity while minimizing mass. Additive manufacturing processes enable the design of metamaterials that exceed the performance of naturally occurring materials in addition to allowing the integration of non-structural functions. This research explored the use of a high stiffness, high density, small melt pool track width AM material, Inconel 718, to enable the production of metamaterials with finer features possible than can possibly be created using a lower density aluminum alloy material. Various metamaterials were designed utilizing thin wall triply periodic minimal surface infilled sandwich structures. The performance …
Thermal Management Of Satellite Electronics Via Gallium Phase Change Heat Sink Devices, Brian O. Palmer
Thermal Management Of Satellite Electronics Via Gallium Phase Change Heat Sink Devices, Brian O. Palmer
Theses and Dissertations
The purpose of this research was to determine the effectiveness and feasibility of additively manufactured heat sinks using gallium as a phase change material in the thermal management of satellite electronics. A design was created based on the footprint of an Astronautical Development, LLC Lithium 1 UHF radio and six heat sinks were additively manufactured; two each of stainless steel 316, Inconel 718, and ULTEM 9085. Each heat sink was filled with gallium for testing purposes. Models were created to simulate the behavior of the heat transfer and phase change processes occurring within the heat sink. Additionally, laboratory data was …
Effects Of Manufacturing Process Variables On Ultrasonic Testing In Electron Beam Melted Ti-6al-4v, Andrew D. Durkee
Effects Of Manufacturing Process Variables On Ultrasonic Testing In Electron Beam Melted Ti-6al-4v, Andrew D. Durkee
Theses and Dissertations
Further research on validating additive manufacturing production quality is required before the realization of direct print-to-fly application of critical components. This research examines the response of ultrasonic testing as a function of various manufacturing variables in electron beam melted samples of Ti-6Al-4V. Four dimensionally identical blocks with 6 spherical voids at varying depths were manufactured using different combinations of stock powder, edge treatments, and void melting. Scans were completed on two sides of each specimen with the transducer focused on the mid-plane. Additionally, one specimen was scanned 6 times, with the focal plane adjusted for each scan to match the …
Design And Testing Of An Additively Manufactured Cubesat Structural Bus, Karson A. Roberts
Design And Testing Of An Additively Manufactured Cubesat Structural Bus, Karson A. Roberts
Theses and Dissertations
Recent innovations in additive manufacturing and design capabilities have opened the door for more opportunities to integrate multiple functions into a structural de- sign. Specifically, 3D printing through advanced laser powder bed fusion of metal powder allows for the development and integration of advanced structures that were previously unachievable. The demonstration of these techniques on a small satellite results in a structural bus consisting of various external and internal features, increasing its functionality and capabilities beyond simply providing structural support. 3D printing a multi-functional CubeSat bus with these integrated features such as internal lattices and wiring tabs demonstrates a new …
Analysis Of Additively Manufactured Injectors For Rotating Detonation Engines, Michael C. Waters
Analysis Of Additively Manufactured Injectors For Rotating Detonation Engines, Michael C. Waters
Theses and Dissertations
This research represents an experimental and computational analysis of additively manufactured injectors for Rotating Detonation Engines (RDEs) for use in rocket propulsion. This research was based on the manufacture and testing of existing injector element designs using additive techniques. The designs were modeled from geometries gathered from Sutton and Biblarz Elements of Rocket Propulsion [23]. The goal of this research was to characterize the viscous losses of each design based on the discharge coefficient. The designs were computationally simulated to gain insight to the flow characteristics using multiple sets of conditions for surface roughness and inlet pressure. The results were …
Analysis Of Additively Manufactured Lattice Structures Using Finite Element Methods, Christopher A. Box
Analysis Of Additively Manufactured Lattice Structures Using Finite Element Methods, Christopher A. Box
Theses and Dissertations
Additive Manufacturing (AM) processes are well known for their ability to fabricate parts with complex geometries. Lattice structures leverage this ability to create parts with high strength-to-weight ratio and other desirable structural qualities. This research presents a parameterized modeling tool using common Finite Element Analysis (FEA) and scripting software with which aggregated lattice structures can be analyzed, given different geometric properties and loading conditions. A full factorial Design of Experiments is run to explore the effects of various parameters on the strength of lattice structures. Experimental compressive strength results from three FDM-produced PLA lattices are discussed and compared to predictions …
Evaluation Of The Impact Of An Additive Manufacturing Enhanced Cubesat Architecture On The Cubesat Development Process, Rachel E. Sharples
Evaluation Of The Impact Of An Additive Manufacturing Enhanced Cubesat Architecture On The Cubesat Development Process, Rachel E. Sharples
Theses and Dissertations
Additive manufacturing (AM) is a fabrication method ideally suited to low-quantity, highly customized builds, leading to interest in its application to satellite development and manufacturing, where each build is unique. Due to the issues of long development schedules and high development and manufacturing costs, methods are needed in the CubeSat development process to reduce the weight and volume of subsystems and decrease integration time. The work develops an architecture for an AM-augmented CubeSat and examines the AM techniques of embedded electronics, embedded thrusters, and custom radiation-hardened materials can impact the subsystems of a CubeSat. The AM-augmented architecture shows a shift …
Surface Roughness Of Electron Beam Melting Ti-6al-4v Effect On Ultrasonic Testing, Evan T. Hanks
Surface Roughness Of Electron Beam Melting Ti-6al-4v Effect On Ultrasonic Testing, Evan T. Hanks
Theses and Dissertations
Experimental research was conducted on the effects of surface roughness on ultrasonic non-destructive testing of Electron Beam Melted (EBM) additively manufactured Ti-6Al-4V. Additive Manufacturing (AM) is a developing technology with many potential benefits, but certain challenges posed by its use require further research before AM parts are viable for widespread use in the aviation industry. Possible applications of this new technology include, Aircraft Battle Damage Repair (ABDR), small batch manufacturing to fill supply gaps, and replacement for obsolete parts. The research presented here assesses the effectiveness of ultrasonic inspection in detecting manufactured flaws in EBM manufactured Ti-6Al-4V. EBM products are …
Determining The Degree Of The Routinization Of Additive Manufacturing In The Air Logistics Complexes, Candis A. Woods
Determining The Degree Of The Routinization Of Additive Manufacturing In The Air Logistics Complexes, Candis A. Woods
Theses and Dissertations
Fiscal constraints have affected the USAF’s spending and sustainment of weapons systems that are being utilized beyond their programmed life cycle; therefore, it is imperative that processes be given the critical eye for improvement, innovative approaches, and/or best practice implementation. The AFSC, part of the AFMC, has embarked on a groundbreaking effort to transform operations and leverage industry best practices, while maintaining focus on warfighter support to create “The AFSC Way.” The AFSC Way is based on a shared leadership model that emphasizes speed, safety, and quality, which gives way to innovative ideas and new technologies in order to achieve …
Effects Of Additive Manufacturing Methods On The Dynamic Properties Of 15-5ph Stainless Steel, Allison A. Dempsey
Effects Of Additive Manufacturing Methods On The Dynamic Properties Of 15-5ph Stainless Steel, Allison A. Dempsey
Theses and Dissertations
Experimental research was conducted to determine the dynamic properties and characterize the microstructure of 15-5PH Stainless Steel manufactured through Direct Metal Laser Sintering (DMLS) additive manufacturing (AM) processes and heat treated using common heat treatment protocols. A thorough understanding of the material's properties is necessary before such parts are utilized in an operational capacity. Of the five builds, two deviated significantly from the specified composition of 15-5PH stainless steel. The remaining three builds, possessing the desired composition and crystalline structure, were tested in compression and tension at two strain rates. Tension tests using a reflected wave and a momentum trap …