Engineering Commons^™

Improving Cast Steel Rail Coupler Fatigue Resistance Through Local Wire-Arc Additive Manufacturing, Andrew M. Bunge

Dissertations, Master's Theses and Master's Reports

Every year, thousands of cast-steel railcar couplers suffer from corrosion-initiated fatigue cracking in similar areas of the coupler’s knuckle; between 2015 and 2018 about 90,000 knuckles were replaced, otherwise these couplers would have been at risk for unexpected failures. These types of couplers have been common in industrial use as early as 1932, hence it is desirable for a countermeasure to the fatigue cracking that does not involve significantly altering the geometry or casting process. Wire arc additive manufacturing (WAM) is a developing technology which boasts the ability to produce complex near-net-shape components; however, less attention has been paid to …

Nickel Superalloy Composition And Process Optimization For Weldability, Cost, And Strength, Sophie A. Mehl

Dissertations, Master's Theses and Master's Reports

To advance sustainability efforts, electric power plants have reduced specific carbon dioxide emissions by increasing operating temperatures and pressures to improve power generation efficiency. The latest improvements are utilized in advanced ultra-supercritical power generation. To meet these operating conditions, nickel superalloys are used in the highest temperature components; however, they are expensive and present weldability challenges. This project aims to experimentally optimize a nickel superalloy to improve material weldability and decrease cost without compromising strength. Three optimized compositions were developed, and their microstructures and mechanical properties were compared to Nimonic 263, a common nickel superalloy in electric power plants. The …

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Effect Of Sc On Recrystallization Resistance Of Aa7050, Keaton Schmidt

Dissertations, Master's Theses and Master's Reports

The extrusion process involves high temperatures and strains that can result in undesirable microstructures, especially along the surface. Extruded alloys tend to exhibit surface recrystallization during heat treating at regions of higher strains, which can lead to reduced fatigue strength and corrosion resistance. By adding Sc to AA7050, nano-sized dispersoids are formed with Sc cores and Zr shells that restrict recrystallization more than the base alloy that only utilizes Zr. Billets with varying Sc content and a control with only Zr were cast, and extrusions were made in order to compare surface microstructures at varying strains in the as-extruded and …

Stability Of Linicoal-Oxide Electrode Material Under High-Temperature Ceramic Fuel Cell Conditions, Wei Zhang

Dissertations, Master's Theses and Master's Reports

LiNi0.8Co0.15Al0.05O2 (LNCA) is an important cathode material for room-temperature operation of lithium-ion batteries (LIBs). As an emerging research area, LNCA was recently applied as electrodes (both cathode and anode) for high-temperature ceramic fuel cells (CFCs) with impressive performances. However, the stability of LNCA electrode material under CFC operating conditions (i.e., reactive atmospheres and high temperatures) remains unknown. In this dissertation: (1) The stability of LNCA in air and H2 atmospheres was systematically evaluated at elevated temperatures (i.e., the operating electrode environments of H2-fueled CFCs). It was found that LNCA exhibited excellent stability in air within a wide temperature range from …

Quantifying The Evolution Of Strengthening Mechanisms For Commercially Produced Niobium And Titanium Hsla Steel Sheet, Isabella M.W. Jaszczak

Dissertations, Master's Theses and Master's Reports

Strength uniformity along the coil length of commercially produced high-strength, low-alloy (HSLA) steel hot-rolled sheet is crucial to avoid the downgrading of product that does not meet strength specifications. In addition to contributing to precipitation strengthening through the growth of niobium-titanium carbides ((Nb,Ti)-C), niobium hinders austenite recrystallization and refines ferrite grain size. The potency of these strengthening mechanisms relies heavily on the austenite to ferrite transformation kinetics of the hot-rolling process. While niobium’s effect on precipitation strengthening, Hall-Petch strengthening, dislocation strengthening, and solute strengthening have all been studied in literature independently, the interactions of these mechanisms with each other and …

Optimizing The Extrudability Of 6082 Aluminum By Varying The Magnesium And Silicon Concentration, Eli A. Harma

Dissertations, Master's Theses and Master's Reports

Alloy 6082 aluminum is used for high-volume manufacturing in the automotive industry due to its high strength, impact performance, and corrosion resistance. However, given these improved properties, the alloy has decreased formability compared to other 6xxx series alloys, especially in the extrusion process. Controlling the dynamic recovery and recrystallization properties by changing the additions of Mg and Si can improve the hot deformation properties. Five alloys of varying Mg and Si concentrations between 0.6 to 1.2wt% Mg and 0.7 to 1.3wt% Si were made with constant concentrations of Cr, Fe, and Mn and the same homogenization heat treatment. The proposed …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Molecular Modeling Of High-Performance Polymers, Sagar Umesh Patil

Dissertations, Master's Theses and Master's Reports

High-performance polymers are extensively used in the aerospace and aeronautics industries due to their low density, high specific strength, and high specific stiffness. These properties along with better infiltration with reinforcements [carbon nanotubes (CNTs), glass, etc.] capability make them an excellent candidate to fabricate Polymer Matrix Composites (PMCs) tailored for specific applications. The applications range from products used daily to deep space exploration. These materials are subjected to varying temperatures and pressures during fabrication and in service. Therefore, the evolution of their intrinsic properties needs to be studied and their ability to sustain extreme environmental conditions in outer space needs …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

Length-Scale-Dependent Stress Relief Mechanisms In High Purity Indium, Fereshteh Mallakpour

Dissertations, Master's Theses and Master's Reports

Lithium-ion batteries are widely used in portable electronics and electric vehicles. However, due to the presence of flammable liquid electrolytes, these devices fail catastrophically when the cell experiences a short circuit. One attractive solution to this problem is a solid-state battery. As the name implies, the flammable liquid electrolyte is replaced by a non-flammable solid-state electrolyte (SSE). The unexpected, yet frequently observed failure mechanism in these devices is the formation and growth of lithium dendrites originating at the interface between the lithium anode and the SSE. As the dendrites grow, device performance degrades. Once the dendrites completely penetrate the SSE, …

Deformation Manifold Learning Model For Multi Walled Carbon Nanotubes, Shashank S. Pathrudkar

Dissertations, Master's Theses and Master's Reports

Two-Dimensional (2D) materials are being studied widely by researchers due to their superior material properties over the bulk materials. Since the isolation of graphene in 2004, graphene has gained popularity amongst the 2D materials community. Graphene when rolled into sheets form Carbon Nanotubes (CNTs) which possess excellent mechanical and electrical properties. Concentric stacks of CNTs yield Multi-walled Carbon Nanotubes (MWCNTs) which are superior to CNTs in certain aspects. It has been well established that the deformation of CNTs and MWCNTs change their mechanical and electrical properties significantly. This has opened doors for CNTs into numerous applications and also piqued the …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

The Effects Of Molybdenum, Chromium, And Niobium On Gray Iron For Brake Rotor Applications, Matthew Hasbrouck

Dissertations, Master's Theses and Master's Reports

Brake rotor composition and microstructure must be optimized for thermal and mechanical performance to avoid thermal-mechanical cracking, excessive wear, and to reduce noise. Niobium is an element that increases the strength and wear resistance of gray iron; however, the interaction of niobium with other common alloying elements (chromium and molybdenum) is not well understood. Thirteen gray cast iron alloys were produced with varying levels of carbon equivalent (CE), Cr, Mo, and Nb. Bars with four different diameters (8, 14, 22, and 30 mm) were cast from each alloy and microstructural and physical properties such as graphite flake morphology, pearlite spacing, …

Atomistic Monte Carlo Simulation Study Of Phase Transitions In Metal Alloys, Xiaoxu Guo

Dissertations, Master's Theses and Master's Reports

The atomic-scale Monte Carlo simulation study focuses on the intrinsic behaviors of a defect-free crystal that undergoes a cubic-to-tetragonal martensitic transformation. The quasi-spin variable associated with the lattice sites characterizes the local unit cells of the orientation variants of the ground-state martensite phase, which interact with each other through long-range elastic interactions. It is shown that the diffuse scattering in the premartensitic austenite state results from the spatial correlation of the atomic-scale heterogeneous lattice displacements and manifests the displacement short-range ordering. The effects of temperature, elastic anisotropy, and shear modulus softening on the diffuse scattering and displacement short-range ordering are …

Analyzing Variation In Dispersoid Formation In Aluminum Alloys By Minor Changes In Homogenization Temperature, Brendan Treanore

Dissertations, Master's Theses and Master's Reports

The homogenization of billets in the aluminum extrusion industry is a critical step that removes chemical segregation from casting, dissolves low melting point phases, forms nanoscale dispersoid phases, and promotes the beta to alpha transformation of iron particles in the matrix. With ever increasing use of aluminum extrusion in the automotive industry there is a constant need for increased efficiency and consistency in processing of extruded aluminum. The work in this thesis explores the effects of 10°C differences in the homogenization temperature on the formation of dispersoids in 6082 alloys used in the automotive industry. The role of dispersoids is …

Multi-Level Analysis Of Atomic Layer Deposition Barrier Coatings On Additively Manufactured Plastics For High Vacuum Applications, Nupur Bihari

Dissertations, Master's Theses and Master's Reports

While hardware innovations in micro/nano electronics and photonics are heavily patented, the rise of the open-source movement has significantly shifted focus to the importance of obtaining low-cost, functional and easily modifiable research equipment. This thesis provides a foundation of open source development of equipment to aid in the micro/nano electronics and photonics fields.

First, the massive acceptance of the open source Arduino microcontroller has aided in the development of control systems with a wide variety of uses. Here it is used for the development of an open-source dual axis gimbal system. This system is used to characterize optoelectronic properties of …

New Horizons For Processing And Utilizing Red Mud, M. Archambo

Dissertations, Master's Theses and Master's Reports

Red mud is an industrial slurry waste that is produced as a byproduct of the Bayer process for alumina. The waste is generated in large quantities, up to a ratio of 2:1 against the valued product alumina. Red mud exhibits many chemical and physical properties that categorize it as a hazardous material. Due to the addition of sodium hydroxide in processing, the pH is typically at values close to 13. Small particle size discourages separation from water for disposal, so drying red mud happens over many years.

The pH of red mud can be reduced with inexpensive reagents. Carbon dioxide …

Studying The Effects Of Initial Crack Angle On The Crack Propagation In Graphene Nano-Ribbon Through Molecular Dynamics Simulations, Vijay Kumar Pathak

Dissertations, Master's Theses and Master's Reports

In this research, we have worked on the brittle fracture of graphene nano-ribbon to explore the behavior of crack propagation at different crack angles. We have performed classical Molecular Dynamics simulations using LAMMPS at ten different crack angles between 0 degrees and 45 degrees, in an increment of 5 degrees to observe the parameters that dominate the crack path. The graphene nanoribbon is loaded in the zigzag direction by pulling it in the armchair direction with a pre-existing crack in the center. We have used OVITO for the visualization of the simulation. AIREBO potential is employed in this work because …

Role Of Eta Phase Evolution On Creep Properties Of Nickel Base Superalloys Used In Advanced Electric Power Generation Plants, Ninad Mohale

Dissertations, Master's Theses and Master's Reports

Advanced fossil energy power generation plants require materials that withstand high temperatures and corrosive environments. One such material that is used in steam turbines is Nimonic 263. It is a nickel-base superalloy that is principally strengthened by gamma primephase (Ni₃(Ti, Al)) and has an L1₂structure. At extended times and at turbine operating temperatures however, eta (Ni₃Ti) phase is known to form at the expense of gamma prime. Eta has a complex DO₂₄structure and is the stable phase between 750°C and 900°C, but with slow kinetics of formation. Little is understood about eta …

Exploring Rapid Solidification And Equal Channel Angular Pressing In The Fabrication Of Mg-Based Alloys For Medical Applications, Emily Tom

Dissertations, Master's Theses and Master's Reports

The development of magnesium bioresorbable implants has become increasingly popular due to the increased need for temporary implants and magnesium’s excellent biocompatibility and suitable elastic modulus. Even though magnesium is an excellent candidate, when alloyed with other metals magnesium’s corrosion rate becomes too rapid for bioresorbable medical applications. The investigation into novel processing techniques to control the formation of precipitates to improve mechanical strength and ductility as well as corrosion rates has become of interest. This work investigates the combination of two nonequilibrium processing techniques, rapid solidification (RS) and equal channel angular pressing (ECAP), and the effects it has on …

Anaerobic Reductive Bioleaching Of Manganese Ores, Neha Sharma

Dissertations, Master's Theses and Master's Reports

The increasing demand of manganese in the industries and various hindrances in its production from low grade ores by conventional method has made it imperative for researchers around the world to develop a method of manganese extraction from low grade ores that is both environment friendly and economical. Bioleaching has shown significant potential in manganese extraction and efficiencies of extraction have been found to be 70-98% with the help of various bacteria and fungi.

This study focuses on extraction of manganese with the help of mixed bacterial strains that have been collected from their natural anaerobic environment. The extraction of …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Artificial Synthetic Scaffolds For Tissue Engineering Application Emphasizing The Role Of Biophysical Cues, Samerender Nagam Hanumantharao

Dissertations, Master's Theses and Master's Reports

The mechanotransduction of cells is the intrinsic ability of cells to convert the mechanical signals provided by the surrounding matrix and other cells into biochemical signals that affect several distinct processes such as tumorigenesis, wound healing, and organ formation. The use of biomaterials as an artificial scaffold for cell attachment, differentiation and proliferation provides a tool to modulate and understand the mechanotransduction pathways, develop better in vitro models and clinical remedies. The effect of topographical cues and stiffness was investigated in fibroblasts using polycaprolactone (PCL)- Polyaniline (PANI) based scaffolds that were fabricated using a self-assembly method and electrospinning. Through this …

The Effects Of Carbon Equivalent, Return Ratios, Mold Preparation, Riser Feed And Casting Temperature On The Microstructural And Mechanical Properties Of 100-70-03 Pearlitic Ductile Iron, Erin Vandusen

Dissertations, Master's Theses and Master's Reports

The most common and costly detriments to ductile iron foundries are casting defects, particularly in new and complex components. The ability to understand the factors and processes that create microstructures and the associated properties would allow accurate virtual predictions of casting outcomes. An experimental study of standard foundry variables, carbon equivalent, return ratio, mold preparation, riser feed, and casting temperature on a target of 100-70-03 pearlitic, hypereutectic ductile iron provided the groundwork for an ICME database. Density decreased when the fraction of graphite nodules was greater due to the low density of graphite. A greater percentage of return scrap and …

Effect Of Cerium And Magnesium Additions On The Strength And Morphology Of The Intermetallic Compound Layers In Aluminum-Steel Dissimilar Castings, Matt Thomas

Dissertations, Master's Theses and Master's Reports

Dissimilar castings are under investigation due to their light-weighting opportunities within the automotive industry. In this case, dissimilar castings consist of a solid steel core and a poured aluminum component. The strength and integrity of the casting relies on the coherency of the bond between the two components; by optimizing the metallurgical component of the bonding phenomena, the weight and complexity of the insert can be reduced, further increasing the light-weighting opportunities. An interface comprised of intermetallics, generally Fe₄Al₁₃ and Fe₂Al₅, forms between the two components with the latter forming nearest the steel. …

Mo6s8-Based Single-Metal-Atom Catalysts For Methanol Synthesis From Steam Reforming Of Methane, H. T. Zhang Zhang

Dissertations, Master's Theses and Master's Reports

The surge of methane as the major component of natural gas and a dominant greenhouse gas calls for the development of efficient strategy to convert it into valuable liquid chemicals such as methanol. However, the current industrial method for methanol synthesis, which consists of the stream reforming of methane (SRM) to syngas and the followed reaction of syngas to methanol, is rather energy-intensive. Direct conversion of methane into methanol (DMTM) is highly desirable in terms of energy efficiency and economy. DMTM with water as oxidant, i.e. SRM to methanol, is a promising solution but the development highly efficient and selective …

Magnetism In Γ-Fesi2 Nanostructures: A First Principles Study, Sahil Dhoka

Dissertations, Master's Theses and Master's Reports

First-principles calculations are performed on γ-FeSi₂ nanostructures grown on Si (111) and (001) substrate. An attempt to explain the origin of emergent magnetic properties of the metastable gamma phase of iron di-silicide (γ-FeSi₂) is made, which show ferromagnetic behavior on nanoscale, unlike its possible bulk form. Many papers try to explain this magnetism from factors like bulk, epitaxial strain, interface, surface, edges, and corners but doesn’t provide an analytical study for these explanations. Density functional theory is used to analyze the magnetic effects of these factors. The results for the epitaxial structures show no magnetic behavior for …

Buckling Load Study On Pop Nut (Rivet) Using Finite Element Analysis, Saurabh Shankar Shegokar

Dissertations, Master's Theses and Master's Reports

This study highlights the material behavior in riveting operation that includes buckling load analysis using ABAQUS. Finite Element Analysis is used to find the buckling load vs. Displacement results and validated with the results obtained in physical testing of rivet (POP Nut). A mesh sensitivity study is performed using ABAQUS to understand the optimum mesh size for this analysis. An axisymmetric model with contact properties is created and simulated to reduce the simulation time using ABAQUS. The results obtained through Finite Element Analysis show a good resemblance with the testing results. Design changes were suggested to achieve better results that …

Influence Of Rapid Solidification And Wrought Processing On Precipitation Strengthening And Deformation Mechanisms In Al-Sc-Zr Alloys, Yang Yang

Dissertations, Master's Theses and Master's Reports

Al-Sc-Zr alloys have drawn increasing attention in the last several decades due to their strengthening and coarsening resistance. In this study, solute concentrations of Sc and Zr were increased beyond their equilibrium solubilities without primary precipitate formation using melt-spinning. The melt-spun ribbon was metallurgically bonded into bulk shape using extrusion. With the proper aging treatment, the mechanical properties of the supersaturated melt-spun ribbon and extruded rod were found to be significantly higher than a baseline dilute alloy. Increased mechanical properties include microhardness, tensile strength at ambient-temperature, and compressive strength and threshold stress at and elevated-temperature. These increases were related to …