Engineering Commons^™

Formula Sae Interchangeable Independent Rear Suspension Design, Mike Mccune, Daniel Nunes, Mike Patton, Courtney Richardson, Evan Sparer

Mechanical Engineering

The Suspension Solutions design team has completely designed built and tested an independent rear suspension system for the 2008 FSAE car. The car currently features a solid rear axle, and the task of converting it to incorporate an interchangeable rear suspension has been undertaken in order to quantify the advantages and disadvantages of each design philosophy. The car has been properly tested with both the solid axle and independent rear suspension side-by-side, however more testing is suggested. After pushing both setups to their limits on a 50ft diameter skid pad, the test results were quantified, and a final comparison between …

Chip Removal Tool Project, Brett Mori, John Cote, Kyle Rowland, Micah Wells

Mechanical Engineering

The Cal Poly senior project team worked with Helical Products Inc. to develop an automated method for removing swarf and chip buildup from the drill bits of their CNC milling machines. The removal methods in this report were designed for and tested using a Fanuc Robodrill while keeping the potential in mind for their use in other CNC milling machines. After extensive background research, preliminary and prototype design and testing the final chosen design is shown below. The cleaning device is made from flexible sheet metal and placed on a fixture that occupies one of the two pallet locations inside …

Supermileage Team - Urban Concept Competition Vehicle Chassis Design Report, Andrew Allport, Kevin Braico, Kevin Charles, George Kyi, William Lai

Mechanical Engineering

This research and design project was proposed by the Cal Poly Supermileage team. They have requested for our team to design an Urban Concept car, a new category of vehicles to compete for fuel efficiency in the Shell Eco-marathon in 2010. The primary focus of our team is in the design and construction of a chassis the Supermileage team can use for the 2010 competition in Fontana, CA. This design must meet dimensional and functional requirements set by Shell while being designed to maximize efficiency in the competition.

There were various chassis concepts under consideration that would possibly work for …

A Study On Gas Penetration And Fingering Behavior In Injection Molding Of Polymer And Powder Metal Feedstock, Edna I. Orozco

Theses and Dissertations - UTB/UTPA

The effect of processing variables on the level of gas penetration in parts fabricated by gas-assisted injection molding from two different materials was compared. The materials used were polypropylene and stainless steel powder metal/thermoplastic feedstock. Software simulation and physical experiments were conducted. Taguchi analysis was used to reduce the number of experiment trials and to find the optimum processing conditions. Four different variables were changed using nine different combinations. The processing variables are the pressure, the delay time before gas is injected, the temperature of the material injected, and the amount of the material injected. The results showed that the …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Design, Construction And Evaluation Of A Multi Layered Solar Distillation Prototype, Arlen A. Flanagan

BioResource and Agricultural Engineering

Water is arguably the most important resource to any individual; especially in areas of deserts and open oceans where drinkable water suppliers are scarce. The prototype Solar Desalination Unit allows normally undrinkable water to be distilled into a potable source with minimal inputs. The unit’s main power source is focused sunlight to thermally heat water inducing evaporation which is then condensed and collected. While solar desalination has been around for many years, lately more complex designs have been investigated in order to increase yields and efficiency. This paper focuses on the design, construction and testing of a Multi-Plate Solar Desalination …

Manufacture, Characterization, And Application Of Multiwall Carbon Nanotube Composite Crylonitrile-Butadiene-Styrene, Daniel Ray Bortz

University of Kentucky Master's Theses

Carbon nanotubes have been studied for nearly two decades and their amazing properties continue to spur intense investigation in the area of polymer composites. In terms of potential commercialization, mutiwall carbon nanotubes (MWCNTs) are currently the most prevalent and economically viable form of nanotubes. Uncovering innovative means to take full advantage of their properties remains a fundamental issue. In this thesis, viability of their use to reinforce polymeric systems is reported. Acrylonitrilebutadiene- styrene (ABS) was used as the host matrix. MWCNTs were introduced to the ABS matrix via melt compounding. The resulting composite was thoroughly rheologically, thermally, and mechanically characterized. …

An Algorithm To Solve The Associative Parallel Machine Scheduling Problem, Mohannad Abdelrahman Shuaib

University of Kentucky Master's Theses

Effective production scheduling is essential for improved performance. Scheduling strategies for various shop configurations and performance criteria have been widely studied. Scheduling in parallel machines (PM) is one among the many scheduling problems that has received considerable attention in the literature. An even more complex scheduling problem arises when there are several PM families and jobs are capable of being processed in more than one such family. This research addresses such a situation, which is defined as an Associative Parallel Machine scheduling (APMS) problem. This research presents the SAPT-II algorithm that solves a highly constrained APMS problem with the objective …

Investigation Of Selective Laser Sintering Of Zirconium Diboride Parts, Shashwatashish Pattnaik

Masters Theses

"This research investigates the fabrication of three-dimensional parts from ZrB₂, an ultra high temperature ceramic (UHTC), using the selective laser sintering (SLS) process. Based on an experimental investigation, optimum values for the SLS parameters (scan speed, laser power, energy density, scan spacing and layer thickness), used on a DTM Sinterstation 2000, were determined to build green ZrB₂ parts with high integrity and sharp geometrical features. This was done by melting the polymer binder used to bond the ceramic particles layer-by-layer according to the cross-section of a CAD model. The use of a sacrificial plate to eliminate cracks in the bottom …

Development Of Extrusion On Demand For Ceramic Freeze-Form Extrusion Fabrication Processes, Parimal Sanjay Kulkarni

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is a Solid Freeform Fabrication method. It involves the deposition of a ceramic paste in a layer by layer manner to construct a three dimensional structure. The ceramic paste used in this process consists of a high solids loading of ceramic powder mixed with water and a nominal amount of an aqueous organic binder. These characteristics make the process environmentally friendly. Also the absence of dies or molds in the process makes it suitable for fabrication of materials like ceramics. In the past, parts have been fabricated with continuous extrusion of a ceramic paste. In FEF, …

The Future Of The Irish Manufacturing Industry In Relation To Global Competitiveness, Joceley Martins Wilson

Theses

This study is an examination of the challenges faced by the manufacturing sector in Ireland. As the speed of globalization intensifies, new demands are constantly being levied on the manufacturing sector. In order to maintain this very important sector in Ireland, the manufacturing industry must promote constant innovation, automation and specialization, specifically in niche areas where there is a requirement for specific specialized skills, and where the labor cost is not a prohibitive or fundamental issue.

Innovation has been a key success factor for the manufactures to date, and will continue to be an ai'ea of focus as competitive forces …