Engineering Commons^™

Methods And Systems For Fault Diagnosis In Nuclear Power Plants, Jianping Ma

Electronic Thesis and Dissertation Repository

This research mainly deals with fault diagnosis in nuclear power plants (NPP), based on a framework that integrates contributions from fault scope identification, optimal sensor placement, sensor validation, equipment condition monitoring, and diagnostic reasoning based on pattern analysis. The research has a particular focus on applications where data collected from the existing SCADA (supervisory, control, and data acquisition) system is not sufficient for the fault diagnosis system. Specifically, the following methods and systems are developed.

A sensor placement model is developed to guide optimal placement of sensors in NPPs. The model includes 1) a method to extract a quantitative fault-sensor …

Helical Pile Installation Torque And Capacity Correlations, Jared Louis Harnish

Electronic Thesis and Dissertation Repository

Large diameter helical piles are being utilized increasingly to support large compressive and tensile loads. Both the magnitude of the required installation torque and the pile capacity can be directly attributed to the soil shearing resistance developed over the embedded area of the pile including the shaft and helical plates. Hence, the pile capacity can be correlated to the installation torque. Such correlations are widely used in helical pile industry as a means for quality control/quality assurance. However, the reliability of capacity-torque correlations for predicting the large diameter helical piles is adversely affected by the inaccurate measurement of the installation …

Static And Dynamic Response Of Silty Toyoura Sand With Pva Fibre And Cement Additives, Colin J.R. Schmidt

Electronic Thesis and Dissertation Repository

After the Great East Japan Earthquake of 2011, nearly 24 million tons of disaster debris such as concrete products, natural and polymeric fibres, and tsunami deposits remained on the coast of Japan. Much of this debris was recycled and repurposed in engineering projects such as embankments, park restoration, and agricultural field restoration around Tokyo Bay, one of the hardest hit regions of the country. Such a major disaster developed a need for the stabilization of the liquefaction susceptible regions of the reclaimed Tokyo Bay coastline. This thesis specifically focuses on the stabilization against liquefaction of Toyoura sand with the typical …

Engineering Periodontal Tissue Regeneration With The Use Of A Novel Periostin Electrospun Scaffold, Kendal I. Creber

Electronic Thesis and Dissertation Repository

Clinical therapies for the treatment of periodontitis are unable to reproducibly stimulate regeneration of the periodontium. We assessed the use of a novel electrospun type I collagen scaffold containing recombinant periostin to stimulate regeneration of the periodontal ligament (PDL) and bone. Human PDL cells demonstrated the ability to form a mineralized matrix in vitro and reduced osteogenic potential with increased donor age. In vitro analysis indicated scaffolds were biocompatible, however, periostin did not significantly influence adhesion or growth. In the healing of fenestration defects in rats, type I collagen scaffolds (with and without periostin) initially delayed cell infiltration and increased …

The Study Of Mixing And Initial Granule Formation During High Shear Granulation Of Pharmaceutical Powders, Aveen Alkhatib

Electronic Thesis and Dissertation Repository

Wet granulation is the agglomeration of particles using a liquid binder to form granules. The process is extensively used in the pharmaceutical industry to manufacture tablets, as granulation minimizes segregation, dust, and improves flowability. Granule uniformity is important in pharmaceutical manufacturing, as the tablet must contain a uniform distribution of excipients in the product in order to comply with United States Food and Drug Administration (FDA) regulations. The research presented in this thesis focuses on the influence of formulation and process parameters on granule formation. Sugar spheres were initially used to study segregation during the dry mixing phase of high …

Characterization Of High-Pressure-Die-Cast Magnesium Alloy Am60, Hooman Baghaei Anaraki

Electronic Thesis and Dissertation Repository

The primary goal of this study is the characterization of high pressure die cast magnesium alloys AM60 so that the failure model which is proposed by J.Weiler can be validated for two new castings. The input variables of failure model can be determined by characterization of different regions within the castings. Based on the location of gate system, the desired regions are identified across both castings and tensile specimens are extracted from various regions. Therefore the local mechanical properties are determined, and fracture strain of samples ranges from 1.2 to 9.5%. The area fraction of porosities and skin fraction of …

Rotor Position Identification For Brushless Dc Motor, Muhammad Ikhlas

Electronic Thesis and Dissertation Repository

Permanent magnet BLDC motors are characterized by a central magnetic core, called the rotor, and fixed electric coils (usually six) equally spaced in a ring around the core, called the stator. Motor movement is controlled by alternately energizing and de-energizing the stator coils to create a rotating magnetic field that propels the rotor. In order for this process to work correctly, BLDC motors required a technology called electronic commutation, in which the coil currents must be very carefully synchronized to rotor position to ensure that the rotating field is correctly aligned with the permanent magnetic field in the rotor. Usually …

Thermal Convection In Non-Fourier Fluids And Application To Liquid Helium Ii, Mohammad Niknami Esfahani

Electronic Thesis and Dissertation Repository

This thesis examines different conditions for which non-Fourier effects can be significant in the flow of fluids. Non-Fourier fluids of dual-phase-lagging type (DPL) possess a relaxation time and a retardation time, reflecting the delay in the response of the heat flux and the temperature gradient with respect to one another. For non-Fourier fluids of single-phase-lagging type (SPL) the retardation time is zero. Non-Fourier fluids span a wide range of applications, including liquid helium, nanofluids and rarefied gases. The parallels between non-Fourier fluids and polymeric solutions are established.

The instability of steady natural convection of a thin layer of non-Fourier fluid …

Development And Study Of Measurement Methods For Jets And Bogging In A Fluidized Bed, Majid Hamidi

Electronic Thesis and Dissertation Repository

In the Fluid Coking process, if the local concentration of liquid is very high, particles may stick together which can eventually result in process upset because of poor fluidization or even defluidization, a condition commonly known in industry as "bogging".

Using a capacitance sensor, the void distribution in a bed of coke particles can be visualized. The voidage fluctuations caused by gas bubbles have been shown to change dramatically as the bed becomes bogged. Therefore, capacitance sensors should be able to predict the bogging condition in fluid cokers.

The first part of the thesis focused on designing noiseless capacitance sensors …

Cluster Fluid Dynamics In Down Flow Reactors: Experimental And Modeling Study, Angel Virgilio Lanza Soto

Electronic Thesis and Dissertation Repository

Gas–solid concurrent downers possess unique features when compared to other gas–solid systems. Establishing their fluid dynamic properties requires both experimental measurements of gas-solid flow properties and computational modeling.

Measuring gas-solid flow properties such as cluster solid concentrations, individual cluster slip velocities, and cluster sizes, involves the use of specialized optical equipment, as well as a rigorous data analysis methodology. In addition, the modeling of the fluid dynamics of gas-solid flows in downer units offers special challenges such as establishing a proper drag model, cluster configuration and sizes, sphericity, boundary conditions, among other issues.

In this PhD dissertation, the fluid dynamics …

Thermal Conversion Of Triglycerides Of Vegetable Oil For Production Of Renewable Lamp Fuel, Jamie A. Gregory

Electronic Thesis and Dissertation Repository

The thermal treatment of crop oils was investigated with the aim to produce a renewable, liquid fuel suitable for use in wick-based lighting systems. Specific objectives include reducing fuel viscosity and improving wickability in traditional flat cotton wicks. Pyrolysis and visbreaking processes were the two methods of thermal treatment that were studied. Visbreaking was a semi-batch process carried out in a stirred tank reactor at temperatures ranging from 300 to 500 °C. Pyrolysis utilized a continuous system with a mechanically fluidized bed reactor at temperatures ranging from 400- 650 °C. Initial testing with soybean oil feedstock demonstrated that pyrolysis was …

A Self-Potential For Monitoring Self-Sustaining Treatment For Active Remediation (Star), Mehrnoosh Ebrahimzadeh

Electronic Thesis and Dissertation Repository

Self-sustaining Treatment for Active Remediation (STAR) is a novel soil remediation approach for Non-Aqueous Phase liquids (NAPLs) embedded in a porous medium. STAR is based on liquid smoldering combustion which destroys NAPLs while simultaneously generating heat due to the exothermic oxidation reaction. The technique is currently in use in several field pilot tests and a full-scale site remediation. Propagation of the smoldering front is monitored in the field by temperature data obtained from a thermocouple network, with limited resolution. Geophysical techniques, such as Self-Potential (SP), have potential as a non-destructive means for monitoring remediation processes. The SP method measures natural …

Resting-State Functional Network Disruptions In A Rodent Model Of Mesial Temporal Lobe Epilepsy (Tle), Ravnoor Singh Gill

Electronic Thesis and Dissertation Repository

Mesial temporal lobe epilepsy (TLE) is the most common form of drug-refractory epilepsy. The clinical application of non-invasively mapped networks using resting-state functional magnetic resonance imaging (rsfMRI) in humans has been rather limited due to heterogeneous (varying etiology, drugs, onset, latent period, etc.) patient groups. We employed a pharmacological (kainic acid) rodent model of TLE to measure the extent of functional network disruptions using rsfMRI, and study selected behaviors and olfactory to hippocampus transmission. Graph theoretical network modelling and analysis revealed significant increase in functional connectivity connectivity to the temporal lobe (hippocampus) in epileptic-rats compared to controls in the limbic …

Power Management Strategies For Islanded Microgrids, Hisham Mahmood

Electronic Thesis and Dissertation Repository

The focus of this thesis is on developing power management strategies for islanded microgrids, at the primary and the secondary hierarchal control layers. At the Primary Control Layer, the main objective of the proposed strategies is to achieve decentralized power management of Photovoltaic (PV) and battery storage in islanded microgrids. In contrast to the common approach of controlling the PV unit as a current source, in the proposed strategies, the PV unit is controlled as a voltage source that follows a multi-segment adaptive power/frequency characteristic curve. The strategies are implemented locally at the units using multi-loop controllers without relying on …

Production And Applications Of Formaldehyde-Free Phenolic Resins Using 5-Hydroxymethylfurfural Derived From Glucose In-Situ, Yongsheng Zhang

Electronic Thesis and Dissertation Repository

The phenol-formaldehyde (PF) resin manufacturing industry is facing a growing challenge with respect to concerns over human health, due to the use of carcinogenic formaldehyde and sustainability due to the use of petroleum-based phenol in PF resin manufacture. Glucose and its derivative, 5-hydroxymethylfurfural (5-HMF), have proven to be potential substitutes for formaldehyde in the synthesis of phenolic novolac resins.

This thesis investigated a number of glucose and 5-HMF resin systems including the curing of phenol-glucose novolac resin (PG) with a bis-phenol-A type epoxy. The curing process was modeled according to the Sestak-Berggren equation (S, B) using Málek methods. This was …

Wind And Thermal Effects On Ground Mounted Photovoltaic (Pv) Panels, Chowdhury Mohammad Jubayer

Electronic Thesis and Dissertation Repository

A combination of Computational Fluid Dynamics (CFD) simulations and wind tunnel experiments are carried out to investigate the effects of wind on the aerodynamic loading and heat transfer of a ground mounted stand-alone photovoltaic (PV) panel with tilt angle of 25^o in open country atmospheric boundary layer. Several azimuthal wind directions are considered: Southern 0^o, Southwest 45^o, Northwest 135^o and Northern 180^o. Three dimensional Reynolds-Averaged Navier-Stokes (RANS) approaches with an unsteady solver using Shear Stress Transport (SST) k-ω turbulence closure are employed for the CFD simulations, whereas Particle Image Velocimetry (PIV) and …

Applying Probabilistic Methods To The Nato Military Load Classification System For Bridges, Andrew J. Macdonald

Electronic Thesis and Dissertation Repository

Military vehicles frequently use civilian bridges. The loading effects of military vehicles, both wheeled and tracked, are specific and different than those of civilian vehicles in normal traffic. Calibration to determine appropriate load factors for military loading of civilian bridges has not been fully performed and the corresponding levels of safety have not been quantified. This lack of calibration prevents the implementation of limit state design methods for military bridges and the evaluation bridges for military loading. This thesis quantifies probabilistically the single lane traffic load effects on interior girders of simply supported slab-on-girder bridges for three military vehicles in …

Hydrolytic Depolymerization Of Lignin For The Preparation Of Polyols And Rigid Polyurethane Foams, Nubla Mahmood

Electronic Thesis and Dissertation Repository

This doctoral study was aimed to produce bio-polyols from Kraft lignin (KL) and hydrolysis lignin (HL) via depolymerization and utilize the lignin-derived bio-polyols in the preparation of bio-based rigid polyurethane (BRPU) foams at high percentage of bio-contents (50-70 wt.%). This study demonstrated that depolymerization is a practical and effective approach to unleash the potential of utilization of lignin, of complex structures and low reactivity/functionality, for bioproducts and biomaterials.

Depolymerization of KL was realized in alkaline medium using water alone as a solvent or employing water-ethylene glycol (EG) mixture via a low pressure (psig) proprietary process, both effective for producing low …

On The Application Of Mechanical Vibration In Robotics-Assisted Soft Tissue Intervention, Iman Khalaji

Electronic Thesis and Dissertation Repository

Mechanical vibration as a way of transmitting energy has been an interesting subject to study. While cyclic oscillation is usually associated with fatigue effect, and hence a detrimental factor in failure of structures and machineries, by controlled transmission of vibration, energy can be transferred from the source to the target. In this thesis, the application of such mechanical vibration in a few surgical procedures is demonstrated.

Three challenges associated with lung cancer diagnosis and treatment are chosen for this purpose, namely, Motion Compensation, tumor targeting in lung Needle Insertion and Soft Tissue Dissection:

1. A robotic solution is proposed …

A New Generation Of Polymer/Ceramic Composite Biomaterials For Bone Regeneration, Mehrnaz Salarian

Electronic Thesis and Dissertation Repository

There is a substantial emerging interest for fundamental and applied research on the reinforcement of polymeric materials using nanotechnology. In the biomedical industry, development of novel bone cement composite materials with enhanced mechanical properties is of tremendous potential importance. The most universally used injectable bone cement is made of poly(methyl methacrylate) (PMMA); however, the major disadvantage of PMMA is its non-biodegradability. Polymers such as poly(propylene fumarate) (PPF) and polycaprolactone (PCL) are biodegradable, but suffer from a lack of mechanical properties. The aim of this research was to test the efficacy of these biodegradable polymers integrating nanotechnology for the development of …

Posture-Dependent Projection-Based Force Reflection Algorithms For Bilateral Teleoperators, Ali Moatadelro

Electronic Thesis and Dissertation Repository

It was previously established that the projection-based force reflection (PBFR) algorithms improve the overall stability of a force reflecting teleoperation system. The idea behind the PBFR algorithms is to identify the component of the reflected force which is compensated by interaction with the operator's hand, and subsequently attenuate the residual component of the reflected force. If there is no a priori information regarding the behaviour of the human operator, the PBFR gain is selected equal to sufficiently small constant in order to guarantee stability for a wide range of human operator responses. Small PBRF gains, however, may deteriorate the transparency …

Treatment Of Synthetic Oil Sands Tailing Water With Activated Carbon, Alfredo Martinez Iglesias

Electronic Thesis and Dissertation Repository

The extraction of bitumen from the Canadian tar sands has thus far generated approximately 840 billion liters of oil sands process affected water (OSPW) that is currently being stored in containment ponds. OSPW is known to be acutely toxic to various organisms, due to the presence of naphthenic acids (NAs). The scale and sheer volume of OSPW being stored in tailing ponds have generated serious public concerns. Many emerging technologies have been investigated as treatment options for OSPW reclamation. This work studied the feasibility of using granular activated carbon (GAC) to adsorb several naphthenic acids in a model solution of …

Poly(Ester Amide) And Poly(Ethyl Glyoxylate) Nanoparticles For Controlled Drug Release, Amira Mohamed Moustafa

Electronic Thesis and Dissertation Repository

The objective of this research was to develop polymeric nanoparticles (NPs) having improved drug release properties for drug delivery. Poly(ester amide)s (PEAs) are promising biodegradable polymers. PEA NPs were prepared via emulsification-evaporation and salting-out methods and optimized through by varying different processing parameters. Polymer-model drug conjugates based on PEAs containing L-aspartic acid and rhodamine B were synthesized and used for NP preparation. Release behavior was studied and compared to a control system with physically encapsulated rhodamine B. It was shown that the release of rhodamine B from the covalent system did not show the burst effect and exhibited a slower …

Digestion Of Municipal Wastewater Biosolids Using An Anaerobic Fluidized Bed Bioreactor (Anfbr), Zhenqi Wang

Electronic Thesis and Dissertation Repository

This research investigated the efficacy of the anaerobic fluidized bed bioreactor (AnFBR) technology in treating municipal wastewater sludges. Primary sludge (PS) and thickened waste activated sludge (TWAS) were studied in two lab-scale AnFBRs using High-density polyethylene (HDPE) as carrier media. PS was investigated at various organic loading rates (OLRs) ranging from 9 to 18 kg chemical oxygen demand (COD)/m³-d corresponding to hydraulic retention times (HRTs) of 2 to 4 days, with maximum COD and volatile suspended solid (VSS) removal efficiency of 70% and 72%, respectively. For TWAS, VSS destruction efficiency varied from 53% at an HRT of 4 …

Scale-Up Methodology For Bench-Scale Slurry Photocatalytic Reactors Using Combined Irradiation And Kinetic Modelling, Patricio J. Valades Pelayo

Electronic Thesis and Dissertation Repository

The present study focuses on developing a predictive methodology to scale-up a slurry annular photoreactor using a TiO₂ Degussa P25 from the bench-scale to a pilot-plant scale. The bench-scale photoreactor is a Photo-CREC-Water II, a 2.65 L internally-irradiated slurry annular photocatalytic reactor. The pilot-plant scale photoreactor is a Photo-CREC Water Solar Simulator, a 9.8 L pilot-plant photoreactor, externally irradiated by eight lamps.

The adopted methodology allows the independent validation of radiative and kinetic models avoiding cross-correlation issues. The proposed approach involves two Monte Carlo methods, to model the Radiative Transfer Equation (RTE) inside each photoreactor. With this end, a …

Design Of A Haptic Interface For Medical Applications Using Magneto-Rheological Fluid Based Actuators, Nima Najmaei

Electronic Thesis and Dissertation Repository

This thesis reports on the design, construction, and evaluation of a prototype two degrees-of-freedom (DOF) haptic interface, which takes advantage of Magneto-Rheological Fluid (MRF) based clutches for actuation. Haptic information provides important cues in teleoperated systems and enables the user to feel the interaction with a remote or virtual environment during teleoperation. The two main objectives in designing a haptic interface are stability and transparency. Indeed, deficiencies in these factors in haptics-enabled telerobotic systems has the introduction of haptics in medical environments where safety and reliability are prime considerations. An actuator with poor dynamics, high inertia, large size, and heavy …

Enhanced Dechlorination Of 1,2-Dichloroethane By Coupled Nano Iron-Dithionite Treatment, Ariel Nunez Garcia

Electronic Thesis and Dissertation Repository

1,2-dichloroethane (1,2-DCA) is a chlorinated solvent classified as a probable human carcinogen. Due to its extensive industrial applications, widespread contamination and recalcitrance towards abiotic dechlorination, 1,2-DCA remains a challenging compound for the remediation community and one of the great research interests. Batch experiments combining bimetallic or monometallic nZVI (stabilized or non-stabilized) with sodium dithionite were conducted for the degradation of 1,2-DCA. These experiments have yielded up to 92 % degradation of the initial 1,2-DCA concentration over the course of a year. Observed pseudo-first order rate constants (k_obs) range from 3.8 x 10^-3 to 7.8 x 10^{-3 …}

Influence Of Water Chemistry Parameters On The Dissolution Rate Of The Lead (Ii) Carbonate Hydrocerussite, Caitlin Se Kushnir

Electronic Thesis and Dissertation Repository

This work has focused on the kinetic dissolution of the lead (II) carbonate hydrocerussite (Pb₃(CO₃)₂(OH)₂) under four pH conditions (7.5, 8, 9, 10), three dissolved inorganic concentrations (DIC; 10, 20, 50 mg C/L), and three initial hydrocerussite concentrations (10, 20, 50 mg/L) in batch experiments. Experiments were performed in at least duplicate to determine total dissolved lead dissolution curves at short time scales (hr.). All equilibrium dissolved lead concentrations were achieved in 40 minutes or less, and matched trends from previous studies; pH 7.5 and pH 10 corresponding to the highest and …

Miniature Cone Penetration Test On Loose Sand, Sepideh Damavandinejad Monfared

Electronic Thesis and Dissertation Repository

Considering the difficulties associated with preparing loose sand samples in large calibration chambers and wide area of research on the behavior of loose sands, miniature calibration chamber experiments are used to perform cone penetration tests on soils in different states. A miniature cone calibration chamber has been designed and developed in this study. Nineteen tests have been performed on Ottawa sand and the results are compared to the available data in the literature. The accuracy of the results is validated by comparing the results with the suggested rate for the cone resistance in sands in literature. More specifically, results are …

Numerical Modeling Of Deformation, Oscillation, Spreading And Collision Characteristics Of Droplets In An Electric Field, Osameh Ghazian

Electronic Thesis and Dissertation Repository

Electric field induced flows, or electrohydrodynamics (EHD), have been promising in many fast-growing technologies, where droplet movement and deformation can be controlled to enhance heat transfer and mass transport. Several complex EHD problems existing in many applications were investigated in this thesis.

Firstly, this thesis presents the results of numerical simulations of the deformation, oscillation and breakup of a weakly conducting droplet suspended in an ambient medium with higher conductivity. It is the first time that the deformation of such a droplet was investigated numerically in a 3D configuration. We have determined three types of behavior for the droplets, which …