Engineering Commons^™

Investigation Of Topological Phonons In Acoustic Metamaterials, Wenting Cheng

Dissertations

Topological acoustics is a recent and intense area of research. It merges the knowledge of mathematical topology, condensed matter physics, and acoustics. At the same time, it has been pointed out that quasiperiodicity can greatly enhance the periodic table of topological systems. Because quasiperiodic patterns have an intrinsic global degree of freedom, which exists in the topological space called the hull of a pattern, where the shape traced in this topological space is called the phason. The hull augments the physical space, which opens a door to the physics of the integer quantum Hall effect (IQHE) in arbitrary dimensions. In …

Optical Engineering Of Iii-Nitride Nanowire Light-Emitting Diodes And Applications, Ha Quoc Thang Bui

Dissertations

Applications of III-nitride nanowires are intensively explored in different emerging technologies including light-emitting diodes (LEDs), laser diodes, photodiodes, biosensors, and solar cells. The synthesis of the III-nitride nanowires by molecular beam epitaxy (MBE) is investigated with significant achievements. III-nitride nanowires can be grown on dissimilar substrates i.e., silicon with nearly dislocation free due to the effective strain relaxation. III-nitride nanowires, therefore, are perfectly suited for high performance light emitters for cost-effective fabrication of the advanced photonic-electronic integrated platforms. This dissertation addresses the design, fabrication, and characterization of III-nitride nanowire full-color micro-LED (µLED) on silicon substrates for µLED display technologies, high-efficient …

Intermittent Dynamics Of Dense Particulate Matter, Chao Cheng

Dissertations

Granular particle systems are scattered around the universe, and they can behave like solids when there exist strong force-bearing networks, so that the granular system can resist certain stress without deformation. When such a network is not present, particles yield to small stress and behave like a fluid. A wide range of systems exhibit intermittent dynamics as they are slowly loaded, with different dynamical regimes governing many industrial and natural phenomena. While a significant amount of research on exploring intermittent dynamics of granular systems has been carried out, not much is known about the connection between particle-scale response and the …

Investigation Of Topological Phonons In Discrete Mechanical Metamaterials, Kai Qian

Dissertations

The study of topological mechanical metamaterials is a new emerging field that focuses on the topological properties of artificial mechanical structures. Inspired by topological insulators, topological mechanism has attracted intensive attention in condensed matter physics and successfully connected the quantum mechanical descriptions of electrons with the classical descriptions of phonons. It has led to experiments of mechanical metamaterials possessing topological characteristics, such as topologically protected conducting edges or surfaces without back-scattering. This dissertation presents a new experimental approach for mechanically engineering topological metamaterials based on patterning magnetically coupled spinners in order to localize the propagation of vibrations and evaluate different …

A Framework For Using Fused Image Data In Statistical Process Control, Shengfeng Chen

Dissertations

The use of image data in manufacturing quality control systems has grown rapidly over the years. Technological advancements in imaging devices (e.g., digital cameras, x-ray scanners, infrared cameras) have provided convenient and cost-effective ways to obtain images. These images contain important quality features (e.g., textures and product dimensions) that can be used to monitor, diagnose, predict, and control manufacturing processes. A key tool for monitoring images is statistical process control charts. Integrating images of parts to detect process shifts can significantly improve a quality systems efficiency. Unfortunately, appropriate techniques that take full advantage of data-rich images for control charting are …

Calculating Elastic Properties Of Confined Simple Fluids, Christopher D. Dobrzanski

Dissertations

Confinement in nanoporous materials is known to affect many properties of the fluids confined within their pores. The elastic properties are no exception. This dissertation begins with an overview of the relevant literature on ways of obtaining elastic properties of confined fluids. It outlines some fundamental gaps in our understanding. The chapters following address some of these gaps in understanding elastic properties of the confined fluid, in particular, how the shape of the confining pore matters, how supercriticality effects the properties, how an equation of state designed for confined fluids can be used to calculate elastic properties, and if an …

Customized Boron And Magnesium-Based Reactive Materials Prepared By High Energy Mechanical Milling, Xinhang Liu

Dissertations

New reactive materials need to be developed having biocidal combustion products. When ignited, such material can add chemical biocidal effects to the common effects of high temperature and pressure. Biocidal combustion products are capable of deactivating harmful spores or bacteria, which can be released by targets containing biological weapons of mass destruction. Research showed that halogens, especially iodine, are effective as biocidal components of reactive material formulations. Recently, magnesium combustion product MgO is also found to have a biocidal effect. Thus, advanced formulations containing both magnesium and iodine are of interest; such formulations are prepared and investigated here.

Reactive materials …

Enzymatic Biofuel Cells In A Sandwich Geometry With Compressed Carbon Nanotubes/Enzyme Electrodes & Hybrid Patch Applications, Biao Leng

Dissertations

Enzymatic biofuel cells (EBFCs) convert the chemical energy of biofuels, such as glucose and methanol, into electrical energy by employing enzymes as catalysts. In contrast to conventional fuel cells, EBFCs have a simple membrane-free fuel cell design due to the high catalytic specificity of the enzymes, but the power densities obtained are lower. Although the primary goal of research on EBFCs has been to develop a sustainable power source that can be directly implanted in the human body to power bio-devices, other applications such as the use of a flexible film or fuel cell patch as a wearable power source …

Measurement Of Stresses And Their Effect On Transport In Thin Film Battery Electrodes, Subhajit Rakshit

Dissertations

At the moment, there is a significant push towards environmentally friendly energy production and gasoline-free transportation technologies. As a result, there is a renewed interest in energy storage devices such as lithium-ion batteries which will play a key role in providing energy storage capability for these applications. However, the current battery technology is reaching its limits and may not meet future energy storage demands. The increased demand and the limited lithium reserves in geographically remote areas of the earth will lead to higher cost of Li. The alternative battery technologies, such as sodium-ion batteries, are promising due to their low …

Development And Evaluation Of Matrix Material Formulations For Potential Integration Into Immunodiagnostic Biosensors, Payam Aminayi

Dissertations

This study supports the development, characterization and optimization of biosensor material formulations for immunodiagnostic applications based on experimental findings and hypotheses by Wang and Wu [1, 2], and using a test-plate apparatus and thin-film design developed by Young [3].

Certain biosensors working on the basis of conductance/impedance changes have demonstrated their potential to detect various bacteria, enzymes, and biomolecules due to their enhanced electrical properties with incorporated single-walled carbon nanotubes (SWNT). From the work conducted in our laboratory, we are attempting to determine and develop a matrix formulation containing highly dispersed SWNT, antibody and other components that elicit a significantly …

Printing Functional Electronic Circuits And Components, Ahmed Tausif Aijazi

Dissertations

The purpose of this study was to investigate the challenges in printing reliable multilayer flexible circuits, devices and components. Gravure was used as the primary printing process for this work, but due to some limitations of gravure, other printing methods were also investigated. At first a systematic study was done to determine the optimum parameters for the gravure printing of sub 50 micron lines. Commercially available silver nanoparticle inks were printed on a lab scale gravure printer, Accupress®. The highest resolution line that was electrically conductive was 36μm wide. The 9μm, 18μm and 27μm lines were printed but were not …

Integrating 3d Layered Manufacturing With Photonic Sintering, Precision Machining And Smart Coating Techniques For Rapid Casting Applications, Hemant Bohra

Dissertations

Developments in rapid casting technologies have led to a new era of inclusion of 3D printing. Three-Dimensional (3D) printing provides the flexibility and ease of reproducing a sand mold directly from CAD models, eliminating patterning steps, thus reducing the process time for creating prototypes. In addition to minimizing processing steps, 3D printing provides the advantages of higher precision and the ability to produce complex shaped sand molds, but it simultaneously possesses some limitations and concerns related to throughput, safety and logistics.

This study proposes an alternative method for creating sand molds by introducing a hybrid rapid prototyping approach to overcome …

New Media Icc Profiles Construction And Concerns, Reem El Asaleh

Dissertations

With the advent of the modern digital technology, users can now capture an image and reproduce it between different media, such as display it on LCD monitor or tablet computer, print it on desktop printer or send it to a printing press. The challenge has been then to maintain the accuracy of image colors during this reproduction, which has led to the development of Color Management Systems. Using these systems, the color reproduction across-media will be accomplished using device ICC profiles that describe each device’s color characterization data in a standardized format based on International Color Consortium (ICC) specifications.

ICC …

Variable Block Size Motion Compensation In The Redundant Wavelet Domain, Ahmed Abdelgadir Suliman

Dissertations

Video is one of the most powerful forms of multimedia because of the extensive information it delivers. Video sequences are highly correlated both temporally and spatially, a fact which makes the compression of video possible. Modern video systems employ motion estimation and motion compensation (ME/MC) to de-correlate a video sequence temporally. ME/MC forms a prediction of the current frame using the frames which have been already encoded. Consequently, one needs to transmit the corresponding residual image instead of the original frame, as well as a set of motion vectors which describe the scene motion as observed at the encoder. The …

Flexography Printing Of Silver Based Conductive Inks On Packaging Substrates, Ramesh Chandra Kattumenu

Dissertations

Printing technologies for the production of flexible electronics have gained much interest due to its potential as a means to reduce the complexity and costs of present technology. High volume printing techniques like flexography are of great importance in order to produce rolls of flexible electronics printed directly on paper substrates. The proposed research will be focused on RFID components being in-line printed using flexography printing as the manufacturing platform. The properties of substrates and inks and printing process parameters are evaluated to study their effect on printed traces and RFID antenna. It was found in the study that properties …