Engineering Commons^™

Enhanced Optical Bistability With Film-Coupled Plasmonic Nanocubes, Christos Argyropoulos, Cristian Ciraci, David R. Smith

Department of Electrical and Computer Engineering: Faculty Publications

Colloidally synthesized nanocubes strongly coupled to conducting films hold great promise for enhancing different nonlinear optical processes. They exhibit a robust and sensitive scattering response that can be easily controlled by their geometrical and material parameters. Strong local field enhancement is generated at the gap regions between the nanocubes and the metallic film. We show that strong optical bistability and all-optical switching behavior can be obtained by loading these nanogaps with Kerr nonlinear materials. Relatively low input intensities are required to obtain these nonlinear effects. The proposed design can lead to efficient, low-power, and ultrafast all-optical memories and scattering nanoswitches.

Temperature-Dependent Dielectric And Thermal Properties Of Whey Protein Gel And Mashed Potato, Jiajia Chen, Krishnamoorthy Pitchai, Sohan Birla, Ricardo Gonzalez, David Jones, Jeyamkondan Subbiah

Biological Systems Engineering: Papers and Publications

Temperature-dependent dielectric properties (dielectric constant and dielectric loss factor) and thermal properties (thermal conductivity and specific heat capacity) of whey protein gel and mashed potato were measured from -20°C to 100°C. A dielectric properties measurement system and a multipoint temperature calibration protocol were developed. The system consists of an impedance analyzer, a high-temperature coaxial cable, a high-temperature coaxial probe, a micro-climatic chamber and a metal sample holder. Calibrations at two temperatures (25°C and 85°C) were sufficient to accurately measure the dielectric properties of foods from frozen to hot temperatures. Both dielectric constant and dielectric loss factor rapidly increased from -20°C …

Multiplexed Fiber-Ring Laser Sensors For Ultrasonic Detection, Tongqing Liu, Lingling Hu, Ming Han

Department of Electrical and Computer Engineering: Faculty Publications

We propose and demonstrate a multiplexing method for ultrasonic sensors based on fiber Bragg gratings (FBGs) that are included inside the laser cavity of a fiber-ring laser. The multiplexing is achieved using add-drop filters to route the light signals, according to their wavelengths, into different optical paths, each of which contains a separate span of erbium-doped fiber (EDF) as the gain medium. Because a specific span of EDF only addresses a single wavelength channel, mode completion is avoided and the FBG ultrasonic sensors can be simultaneously demodulated. The proposed method is experimentally demonstrated using a two-channel system with two sensing …

Cmos Smart Camera With Focal Plane Neighborhood-Parallel Image Processing, Joseph A. Schmitz

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A neighbhorhood-based smart camera architecture is designed and implemented in a 0.13 μm CMOS technology. Each 8 × 8 region of pixels contains a small processor with local memory, which are tiled to form a full-resolution camera. Each processor operates in parallel, enabling high-speed image processing suitable for tracking and recognition tasks. The architecture features the programming flexibility of designs us- ing chip-level and row-level processors while preserving the scalability of pixel-parallel processing elements. The neighborhood processors are implemented physically be- tween the pixel photodiodes, creating multiple design challenges that are discussed in detail.

Advisors: Sina Balkir and Michael Hoffman

Physical Design Of A Smart Camera With Integrated Digital Pixel Sensors Using A 0.13Μm 8-Layer Metal Cmos Process, Mahir K. Gharzai

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The design of cameras has historically kept imagery and computational circuitry isolated in an attempt to maximize image quality by improving pixel pitch and routing density. Although this technique has worked in creating high density arrays of pixels for large resolution imagers, it has never been able to achieve high framerate computational operations.

A radical approach is introduced to solve this dilemma by creating compact, low- power pixel elements with built-in analog-to-digital converters that directly interface with digital logic. These pixels are capable of integrating alongside logic cells and to create an array of pixels inside the processor that can …

Narrow Grass Hedge Effects On The Transport Of Antimicrobials And Antimicrobial Resistance Genes Following Land Application Of Swine Slurry, Bhavneet Soni

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this study was to determine the effects of manure amendment and narrow grass hedges on the fate and transport of antimicrobials and ARGs in runoff and in soil following the land application of swine manure slurry. Swine manure slurry was land applied to 0.75m wide by 4.0m long plots established on an Aksarben silty clay loam soil located in southeast Nebraska. The treatment factor manure amendment consisted of two levels: no manure application and manure application to meet the 3 year nitrogen (N) requirements for corn. The treatment factor of grass hedge was established for half of …

Drainage Structure Datasets And Effects On Lidar-Derived Surface Flow Modeling, Ruopu Li, Zhenghong Tang, Xu Li, Jessie Winter

School of Natural Resources: Faculty Publications

With extraordinary resolution and accuracy, Light Detection and Ranging (LiDAR)-derived digital elevation models (DEMs) have been increasingly used for watershed analyses and modeling by hydrologists, planners and engineers. Such high-accuracy DEMs have demonstrated their effectiveness in delineating watershed and drainage patterns at fine scales in low-relief terrains. However, these high-resolution datasets are usually only available as topographic DEMs rather than hydrologic DEMs, presenting greater land roughness that can affect natural flow accumulation. Specifically, locations of drainage structures such as road culverts and bridges were simulated as barriers to the passage of drainage. This paper proposed a geospatial method for producing …

Nd-Fe-B Nanoparticles Through Surfactant Assisted Mechanical Milling And Alloy Design, Jordann M. Bornhoft

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surfactant-assisted mechanical milling has been used to produce discrete nanoparticles of both Nd-Fe-B and Sm-Co amenable for bottom-up production of nanostructured or nanocomposite permanent magnets. However, in Nd-Fe-B the comminution of the material proceeds by transgranular fracture, which influences both the morphology of the nanoparticles and the magnetic properties. This paper utilizes alloy design to alter the fracture behavior from transgranular fracture to intergranular fracture. Nd-rich Nd₂Fe₁₄B alloys were produced by melt spinning in an overquenched state. The melt spun ribbons were annealed at 700°C and 800°C to ensure complete crystallization and to form different grain …

Intensity-Demodulated Fiber-Ring Laser Sensor System For Acoustic Emission Detection, Ming Han, Tongqing Liu, Lingling Hu, Qi Zhang

Department of Electrical and Computer Engineering: Faculty Publications

We theoretically and experimentally demonstrate a fiber-optic ultrasonic sensor system based on a fiber-ring laser whose cavity consisting of a regular fiber Bragg grating (FBG) and a tunable optical band-pass filter (TOBPF). The FBG is the sensing element and the TOBPF is used to set the lasing wavelength at a point on the spectral slope of the FBG. The ultrasonic signal is detected by the variations of the laser output intensity in response to the cold-cavity loss modulations from the ultrasonicallyinduced FBG spectral shift. The system demonstrated here has a simple structure and low cost, making it attractive for acoustic …

Acuta Enews December 20132 Vol. 42, No. 12

ACUTA Newsletters

In this Issue...

1 Board Approves Slate of Nominees

1 A Gift from ACUTA to You!

2 Nominate Now for Ruth A, Michalecki Leadership Award i

3 What's on Your Desk?

4 From the Listserv

6 RF Video Distribution Solution for the University of the South

7 Info Links

8 Board Report

9 Welcome New Members

9 Check It Out

A Simple Method For Estimation Of Queue Length, S. P. Anusha, Lelitha Devi Vanajakshi, Anuj Sharma

Department of Civil and Environmental Engineering: Faculty Publications

Urban arterials are characterized by frequent intersections. Queue length and delay are the two primary measures of performance of intersection. These measures play a primary role in determining the arterial performance. This article presents a methodology to determine the number of vehicles in queue at a signalized intersection for under saturated traffic conditions. The results obtained were validated using actual values that are manually extracted. The root-mean-square error is of the range 1.3 vehicles for estimation of number of vehicles in queue. The various aspects that have to be considered in accurate estimation of performance measures are also discussed.

Passive Stormwater Samplers For Sampling Highway Runoff From Bmps: Feasibility Studies, Tian C. Zhang, John S. Stansbury, Massom Moussavi

Nebraska Department of Transportation: Research Reports

No abstract provided.

Development And Evaluation If Best Management Practices For Highway Runoff Pollution Control, Tian C. Zhang, John S. Stansbury, Massom Moussavi

Nebraska Department of Transportation: Research Reports

No abstract provided.

Fea Estimation And Experimental Validation Of Solid Rotor And Magnet Eddy Current Loss In Single-Sided Axial Flux Permanent Magnet Machines, Xu Yang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The rotor and magnet loss in single-sided axial ux permanent magnet (AFPM) machines with non-overlapped windings is studied in this dissertation. Finite element analysis (FEA) estimations of the loss are carried out using both 2D and 3D modeling. The rotor and magnet losses are determined separately for stator slot passing and MMF space harmonics from currents in the stator. The segregation of loss between the solid rotor plate and the magnet is addressed. The eddy current loss reduction by magnet segmentation is discussed as well. Two prototype 24 slot/22 pole single-sided AFPMs, fabricated with both single layer (SL) and double …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason Gerald Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Kolsky Bar Experiment For High-Rate Large Deformations Of Polycarbonate, Jason G. Vogeler

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate (PC) is a tough, transparent engineering thermoplastic. Its impact strength and ability undergo large plastic deformations without shatter make PC an ideal protective material for impact-resilient eyewear, aircraft windows and transparent armor. A good understanding of the response of this material to large deformations at high strain rates is critical for its utilization in these applications. To this end, a striker-less Kolsky bar device is employed in this work for the needed material characterization. The apparatus allow impulsive torsion and/or compression loadings with pulse durations sufficiently long for the plastic flow behavior to develop fully. Three new testing techniques …

Ultrasonic Propagation And Scattering In Pearlitic Steel, Hualong Du

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Diffuse ultrasonic backscatter measurements have been especially useful for extracting microstructural information and for improving flaw detection in materials. In this dissertation, this approach is applied to inspection of railroad wheels. To improve the wear resistance, the tread surfaces of railroad wheels are usually quenched with water to increase the hardness. The pearlite phase of iron, characterized by alternating ferrite and cementite phases, is created by the quenching and the lamellar spacing within grains increases progressively from the quenched tread surface to deeper locations due to the non-uniform cooling rate. The quench depth is an important parameter governing the wheel …

Structural & Magnetic Characterization Study Of Hfco7 Alloy With Substitutions Of Si, Ti, Fe, Mn & B, Jacob A. Lewis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Magnetic materials are a critical component of the modern technological society. The market of high-energy product hard magnets is dominated by the rare-earth element containing neodymium-iron-boron (NdFeB) magnets. As a result of worldwide demand coupled with trade restrictions on rare-earth minerals, new magnet compositions are explored to reduce pressure on the already strained market. The hafnium-cobalt alloy system has shown promise as a candidate for filling the gap in saturation magnetization between rare-earth containing alloys and those made with abundant elements. This study explores the magnetic effects of silicon, titanium, iron, manganese and boron substitutions in the hafnium-cobalt-7 (1:7 atomic …

Experimental Study On The Effect Of Air Flow On Soap Bubble Formation, John M. Davidson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Soap bubbles are a common interfacial fluid dynamics phenomenon having applications such as buoyant hollow spherical fillers and flow visualization of large scale airflows. In contrast to the dynamics of liquid drops in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented, possibly because soap bubbles have gas-liquid-gas interfaces. Having the thin-liquid-film interface seems to alter the characteristics of the bubble/drop creation process. Thus, the main objective of this study is to experimentally examine how airflow develops and interacts with the soap liquid film as the film stretches and finally collapses to pinch-off. …

Implementation Of Precast Concrete Deck System Nudeck (2nd Generation), George Morcous, Maher K. Tadros

Nebraska Department of Transportation: Research Reports

No abstract provided.

Fertilizer Effects On Attaining Vegetation Requirements, Walter H. Schacht, Carol Wienhold

Nebraska Department of Transportation: Research Reports

No abstract provided.

A Study On Countermeasures Against Steganography: An Active Warden Approach, Qilin Qi

Computer and Electronics Engineering: Dissertations, Theses, and Student Research

Digital steganography is a method used for hiding information in digital images. It can be used for secure communication. There have been many robust digital steganography methods invented in recent decades. The steganographic message can be inserted in multimedia cover signal such as audio, image and video. However, this technique also may be used by malicious users to transmit dangerous information through the Internet beyond the control of security agencies. How to detect and/or block potentially dangerous information transmission on the Internet through billions of multimedia files while not affecting innocent multimedia communications becomes a challenging problem. Existing steganalysis methods …

Effects Of Time Varying Background Noise Conditions On Human Perception And Performance, Andrew H. Hathaway

Durham School of Architectural Engineering and Construction: Dissertations, Thesis, and Student Research

This thesis was designed to study the effects of changing noise conditions on human perception and performance. In two phases, participants were exposed to a number of noise conditions and their performance on an arithmetic task involving short-term memory was monitored and their subjective perception of noise conditions was collected via questionnaires.

In the first phase, participants were tested while being subjected to RC-29(H) and RC-47(RV) conditions created by broadband noise fluctuating on different time intervals, resembling the changing noise conditions potentially found in modern HVAC systems. These intervals varied from two minutes to ten minutes. Results show a significant …

The Effect Of Skew Angle On Average Queue Delay At Tee-Intersections: A Simulation Study Using The Texas Model, Manogna Kaluva

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

This thesis explores the effect of intersection skew angle on average queue delay through simulation. The simulation model used is the TEXAS (Traffic Experimental and Analytical Simulation) model. This microscopic simulation model uses a general nonlinear car-following model. It simulates individual intersections and was designed to capture the interaction of traffic operations and intersection geometry.

Simulation models were developed for three stop-controlled, tee-intersections in Lincoln, Nebraska. Field data to develop and calibrate the simulation models were collected. All simulation models were calibrated by adjusting the car following parameters. An experimental design was developed to test the effect of skew angle …

Development Of A Field Test For Total Suspended Solids Analysis, Jessica Branigan

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Total suspended solids (TSS) are all particles in water that will not pass through a glass fiber filter with a pore size less than 2 μm, including sediments, algae, nutrients, and metals. TSS is an important water quality parameter because of its adverse effects on aquatic species and wildlife. The EPA has proposed a regulation for turbidity, a related water quality parameter, which has been stayed pending further testing. TSS is regulated through the EPA via the NPDES in many states. Since there are no accepted field tests for TSS, projects with TSS regulations must send samples to a laboratory …

Clustering And Classification Of Multi-Domain Proteins, Neethu Shah

Department of Computer Science and Engineering: Dissertations, Theses, and Student Research

Rapid development of next-generation sequencing technology has led to an unprecedented growth in protein sequence data repositories over the last decade. Majority of these proteins lack structural and functional characterization. This necessitates design and development of fast, efficient, and sensitive computational tools and algorithms that can classify these proteins into functionally coherent groups.

Domains are fundamental units of protein structure and function. Multi-domain proteins are extremely complex as opposed to proteins that have single or no domains. They exhibit network-like complex evolutionary events such as domain shuffling, domain loss, and domain gain. These events therefore, cannot be represented in the …

Near-Infrared Surface-Enhanced Fluorescence Using Silver Nanoparticles In Solution, Michael D. Furtaw

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fluorescence spectroscopy is a widely used detection technology in many research and clinical assays. Further improvement to assay sensitivity may enable earlier diagnosis of disease, novel biomarker discovery, and ultimately, improved outcomes of clinical care along with reduction in costs. Near-infrared, surface-enhanced fluorescence (NIR-SEF) is a promising approach to improve assay sensitivity via simultaneous increase in signal with a reduction in background. This dissertation describes research conducted with the overall goal to determine the extent to which fluorescence in solution may be enhanced by altering specific variables involved in the formation of plasmonactive nanostructures of dye-labeled protein and silver nanoparticles …

Elementary Implantable Force Sensor For Smart Orthopaedic Implants, Rebecca A. Wachs, David Ellstein, John Drazan, Colleen P. Healey, Richard L. Uhl, Kenneth A. Connor, Eric H. Ledet

Biological Systems Engineering: Papers and Publications

Implementing implantable sensors which are robust enough to maintain long term functionality inside the body remains a significant challenge. The ideal implantable sensing system is one which is simple and robust; free from batteries, telemetry, and complex electronics. We have developed an elementary implantable sensor for orthopaedic smart implants. The sensor requires no telemetry and no batteries to communicate wirelessly. It has no on-board signal conditioning electronics. The sensor itself has no electrical connections and thus does not require a hermetic package. The sensor is an elementary L-C resonator which can function as a simple force transducer by using a …

Ergonomichandle And Articulating Laparoscopictool, M. Susan Hallbeck, Dmitry Oleynikov, Kathryn Done, Tim Judkins, Allison Dimartino, Jonathan Morse, Lawton N. Verner

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention relates to a laparoscopic apparatus. The apparatus includes a handle having a body portion, a top surface, opposite bottom surface, a proximal and distal end. The top surface of the base is contoured to compliment the natural curve of the palm. The apparatus further includes a shaft projecting from the distal end of the handle. The shaft has a proximal and distal end. A control sphere is located on the handle. The control sphere can be moved by one or more of a user's fingers to indicate direction. An end effector is located at the distal end …

Nuts & Bolts, Volume 1, Issue 4

Friends of the Larsen Tractor Museum

Splinter Gallery Construction

Restoration Club

Museum OLLI Program

Free Webinar: Ethanol in Legacy Engines