Engineering Commons^™

Analysis Of Capillary Flow In Interior Corners : Perturbed Power Law Similarity Solutions, Joshua Thomas Mccraney

Dissertations and Theses

The design of fluid management systems requires accurate models for fluid transport. In the low gravity environment of space, gravity no longer dominates fluid displacement; instead capillary forces often govern flow. This thesis considers the redistribution of fluid along an interior corner. Following a rapid reduction of gravity, fluid advances along the corner measured by the column length z = L(t), which is governed by a nonlinear partial differential equation with dynamical boundary conditions. Three flow types are examined: capillary rise, spreading drop, and tapered corner. The spreading drop regime is shown to exhibit column length growth L ~ …

Advances In Autonomous-Underwater-Vehicle Based Passive Bottom-Loss Estimation By Processing Of Marine Ambient Noise, Lanfranco Muzi

Dissertations and Theses

Accurate modeling of acoustic propagation in the ocean waveguide is important to SONAR-performance prediction, and requires, particularly in shallow water environments, characterizing the bottom reflection loss with a precision that databank-based modeling cannot achieve. Recent advances in the technology of autonomous underwater vehicles (AUV) make it possible to envision a survey system for seabed characterization composed of a short array mounted on a small AUV. The bottom power reflection coefficient (and the related reflection loss) can be estimated passively by beamforming the naturally occurring marine ambient-noise acoustic field recorded by a vertical line array of hydrophones. However, the reduced array …

Comparative Estimates Of Anthropogenic Heat Emission In Relation To Surface Energy Balance Of A Subtropical Urban Neighborhood, Changhyoun Park, Gunnar W. Schade, Nicholas D. Werner, David J. Sailor, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Long-term eddy covariance measurements have been conducted in a subtropical urban area, an older neighborhood north of downtown Houston. The measured net radiation (Q*), sensible heat flux (H) and latent heat flux (LE) showed typical seasonal diurnal variations in urban areas: highest in summer; lowest in winter. From an analysis of a subset of the first two years of measurements, we find that approximately 42% of Q* is converted into H, and 22% into LE during daytime. The local anthropogenic heat emissions were estimated conventionally using the long-term residual method and the heat emission inventory approach. We also …

Could Application Of Column-Grid-Array (Cga) Technology Result In Inelastic-Strain-Free State-Of-Stress In Solder Material?, Ephraim Suhir, Reza Ghaffarian, Johann Nicolics

Mechanical and Materials Engineering Faculty Publications and Presentations

Physically meaningful and easy-to-use analytical stress model is developed for a short cylinder (beam) clamped at the ends and subjected to bending caused by the ends offset. The offset is due, in its turn, to an external lateral force that has to be determined from the known offset. It is envisioned that such a beam can adequately represent the state of stress in a column-grid-array (CGA) solder joint interconnection experiencing thermal loading due to the thermal expansion/contraction mismatch of the IC package and the printed circuit board (PCB). The CGA designs are characterized by considerably higher stand-off heights than ball-grid-array …

Predicted Stresses In A Ball-Grid-Array (Bga)/Column-Grid-Array (Cga) Assembly With A Low Modulus Solder At Its Ends, Ephraim Suhir, Reza Ghaffarian

Mechanical and Materials Engineering Faculty Publications and Presentations

A simple, easy-to-use and physically meaningful predictive model is suggested for the assessment of thermal stresses in a ball-grid-array or a column-grid-array with a low modulus solder material at the peripheral portions of the assembly. It is shown that the application of such a design can lead to a considerable relief in the interfacial stresses, even to an extent that inelastic strains in the solder joints could be avoided. If this happens, the fatigue strength of the bond and of the assembly as a whole will be improved dramatically: low-cycle fatigue conditions will be replaced by the elastic fatigue condition, …

A Proposed Integrated Data Collection, Analysis And Sharing Platform For Impact Evaluation, Andreas Kipt, Waylon Brunette, Jordon Kellerstrass, Matthew Podolsky, Javier Rosa, Mitchell Sundt, Daniel Wilson, Gaetano Borriello, Eric Brewer, Evan A. Thomas

Mechanical and Materials Engineering Faculty Publications and Presentations

Global poverty reduction efforts value monitoring and evaluation, but often struggle to translate lessons learned from one intervention into practical application in another intervention. Commonly, data is not easily or often shared between interventions and summary data collected as part of an impact evaluation is often not available until after the intervention is complete. Equally limiting, the workflows that lead to research results are rarely published in a reproducible, reusable, and easy-to-understand fashion for others. Information and communication technologies widely used in commercial and government pro- grams are growing in relevance for international global development professionals and offer a potential …

Effect Of Nano-Oxide Particle Size On Radiation Resistance Of Ironechromium Alloys, Weizong Xu, Lulu Li, James A. Valdez, Mostafa Saber, Yuntian Zhu, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Radiation resistance of Fe-14Cr alloys under 200 keV He irradiation at 500 ­*C was systematically investigated with varying sizes of nano oxide Zr, Hf and Cr particles. It is found that these nano oxide particles acted as effective sites for He bubble formation. By statistically analyzing 700-1500 He bubbles at the depth of about 150-700 nm from a series of HRTEM images for each sample, we established the variation of average He bubble size, He bubble density, and swelling percentage along the depth, and found them to be consistent with the He concentration profile calculated from the SIRM program. Oxide …

Long-Term Stability Of 14yt-4sc Alloy At High Temperature, Lulu Li, Weizong Xu, Mostafa Saber, Yuntian Zhu, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

14YT alloy (Fe-14Cr-0.25wt.%Y2O3-0.4wt.%Ti) with 4 at.% Sc addition was previously reported to exhibit a nanoscale microstructure and high strength when annealed at temperatures up to 1000 °C (0.65Tm) for 1 hour. Here we report that the microstructure and mechanical behavior of 14YT-4Sc alloy after long-term annealing for up to 60 hours at 1000 °C. FIB analysis shows abnormal grain growth with annealing time, while a large fraction of the matrix still consists of nanoscale grains. TEM images reveal a slight growth of nano grains, with estimated grain growth exponent, n, to be 0.29. Sc-Ti-Y-O enriched nano oxide particles (nm) were …

Development Of A National Anthropogenic Heating Database With An Extrapolation For International Cities, David J. Sailor, Matei Georgescu, Jeffrey M. Milne, Melissa A. Hart

Mechanical and Materials Engineering Faculty Publications and Presentations

Given increasing utility of numerical models to examine urban impacts on meteorology and climate, there exists an urgent need for accurate representation of seasonally and diurnally varying anthropogenic heating data, an important component of the urban energy budget for cities across the world. Incorporation of anthropogenic heating data as inputs to existing climate modeling systems has direct societal implications ranging from improved prediction of energy demand to health assessment, but such data are lacking for most cities. To address this deficiency we have applied a standardized procedure to develop a national database of seasonally and diurnally varying anthropogenic heating profiles …

Capillary Channel Flow (Ccf) Eu2-02 On The International Space Station (Iss): An Experimental Investigation Of Passive Bubble Separations In An Open Capillary Channel, Mark M. Weislogel, Andrew P. Wollman, Ryan M. Jenson, John T. Geile, John F. Tucker, Brentley M. Wiles, Andy L. Trattner, Claire Devoe, Lauren M. Sharp, Peter J. Canfield, Jörg Klatte, Michael E. Dreyer

Mechanical and Materials Engineering Faculty Publications and Presentations

It would be signicantly easier to design fluid systems for spacecraft if the fluid phases behaved similarly to those on earth. In this research an open 15:8 degree wedge-sectioned channel is employed to separate bubbles from a two-phase flow in a microgravity environment. The bubbles appear to rise in the channel and coalesce with the free surface in much the same way as would bubbles in a terrestrial environment, only the combined effects of surface tension, wetting, and conduit geometry replace the role of buoyancy. The host liquid is drawn along the channel by a pump and noncondensible gas bubbles …

A Study Of Microwave Curing Of Underfill Using Open And Closed Microwave Ovens, Aditya Thakare

Dissertations and Theses

As the demand for microprocessors is increasing with more and more consumers using integrated circuits in their daily life, the demand on the industry is increasing to ramp up production.

In order to speed up the manufacturing processes, new and novel approaches are trying to change certain aspects of it. Microwaves have been tried as an alternative to conventional ovens in the curing of the polymers used as underfills and encapsulants in integrated circuits packages. Microwaves however being electromagnetic waves have non uniform energy distribution in different settings, causing burning or incomplete cure of polymers.

In this study, we compare …

Vortex Identification In The Wake Of A Wind Turbine Array, Aleksandr Sergeyevich Aseyev

Dissertations and Theses

Vortex identification techniques are used to analyze the flow structure in a 4 x 3 array of scale model wind turbines. Q-criterion, Δ-criterion, and λ₂-criterion are applied to Particle Image Velocimetry data gathered fore and aft of the last row centerline turbine. Q-criterion and λ₂-criterion provide a clear indication of regions where vortical activity exists while the Δ-criterion does not. Galilean decomposition, Reynolds decomposition, vorticity, and swirling strength are used to further understand the location and behavior of the vortices. The techniques identify and display the high magnitude vortices in high shear zones resulting from the …

Global Time-Independent Agent-Based Simulation For Transactive Energy System Dispatch And Schedule Forecasting, Shawn Aaron Chandler

Dissertations and Theses

Electricity service providers (ESP) worldwide have increased their interest in the use of electrical distribution, transmission, generation, storage, and responsive load resources as integrated systems. Referred to commonly as "smart grid," their interest is driven by widespread goals to improve the operations, management and control of large-scale power systems. In this thesis I provide research into a novel agent-based simulation (ABS) approach for exploring smart grid system (SGS) dispatch, schedule forecasting and resource coordination. I model an electrical grid and its assets as an adaptive ABS, assigning an agent construct to every SGS resource including demand response, energy storage, and …

Understanding Residential Location Choices For Climate Change And Transportation Decision Making: Phase 2 Report, Kelly J. Clifton, Steven R. Gehrke, Kristina Marie Currans

Civil and Environmental Engineering Faculty Publications and Presentations

This research builds on the related Phase 1 project. In this second phase, we continue to study neighborhood and housing preferences that shape the residential location decision process. An online experimental survey tool is developed to investigate lifestyle preferences and tradeoffs that households make in their location decisions. This computer-aided experimental survey draws upon stated preference methods to engage participants in questions about residential location and transportation options. The survey infrastructure was extensively piloted (6-10% response rate). The 10-minute survey can be deployed for future investigations. This infrastructure is a contribution for the integration of visualized neighborhood typologies, or concepts, …

Sensible Air To Air Heat Recovery Strategies In A Passive House, Santiago Martin Rodriguez-Anderson

Dissertations and Theses

Due to rising energy costs and concerns about global climate change, high performance buildings are more in demand than ever before. With roughly 20% of the total energy consumption in the United States being devoted to residential use, this sector represents a significant opportunity for future savings. There are many guidelines and standards for reducing building energy consumption. One of the most stringent is the Passive House Standard. The standard requires that that air infiltration is less than or equal to 0.6 air changes per hour at a 50 Pascal pressure difference (ACH 50), annual heating energy is less than …

Estimation Of Transient Temperature Distribution During Quenching, Via A Parabolic Model, Diego E. Lozano, Gabriela Martinez-Solis, Rafael David Mercado-Solis, Rafael Colás, George E. Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional unsteady heat conduction, the radial temperature distribution at the end of an interval belongs to the equation of a parabola. The model was validated using AISI 304 stainless steel test probes (Φ8×40 mm and Φ12×60 mm) quenched from 850 to 900 °C in water and in water-based NaNO2 solutions at 25 °C and in canola oil at 50 °C. Additionally, square test probes (20×20×100 mm) were quenched from 550 …

Thermodynamic Grain Size Stabilization Models: An Overview, Mostafa Saber, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Grain boundaries in a nanocrystalline microstructure produce an increase in the excess free energy of the system. Grain growth is a consequence of the thermodynamic driving force reducing this excess. Thermodynamic stabilization is an approach based on eliminating the driving force by suitable alloy additions that can produce a metastable equilibrium state at the nanoscale grain size, as opposed to kinetic stabilization where the grain growth mobility is restricted by pinning and/or drag mechanisms. The present paper reviews and compares various models proposed for thermodynamic stabilization.

Anisotropy Of The Reynolds Stress Tensor In The Wakes Of Wind Turbine Arrays In Cartesian Arrangements With Counter-Rotating Rotors, Nicholas Hamilton, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

A 4 × 3 wind turbine array in a Cartesian arrangement was constructed in a wind tunnel setting with four configurations based on the rotational sense of the rotor blades. The fourth row of devices is considered to be in the fully developed turbine canopy for a Cartesian arrangement. Measurements of the flow field were made with stereo particle-image velocimetry immediately upstream and downstream of the selected model turbines. Rotational sense of the turbine blades is evident in the mean spanwise velocity W and the Reynolds shear stress −vw. The flux of kinetic energy is shown to be of greater …

High-Resolution Bottom-Loss Estimation Using The Ambient-Noise Vertical Coherence Function, Lanfranco Muzi, Martin Siderius, Jorge E. Quijano, Stan E. Dosso

Electrical and Computer Engineering Faculty Publications and Presentations

The seabed reflection loss (shortly "bottom loss") is an important quantity for predicting transmission loss in the ocean. A recent passive technique for estimating the bottom loss as a function of frequency and grazing angle exploits marine ambient noise (originating at the surface from breaking waves, wind, and rain) as an acoustic source. Conventional beamforming of the noise field at a vertical line array of hydrophones is a fundamental step in this technique, and the beamformer resolution in grazing angle affects the quality of the estimated bottom loss. Implementation of this technique with short arrays can be hindered by their …

Eigenvector Pruning Method For High Resolution Beamforming, Jorge E. Quijano, Lisa M. Zurk

Electrical and Computer Engineering Faculty Publications and Presentations

This paper introduces an eigenvector pruning algorithm for the estimation of the signal-plus-interference eigenspace, required as a preliminary step to subspace beamforming. The proposed method considers large-aperture passive array configurations operating in environments with multiple maneuvering targets in background noise, in which the available data for estimation of sample covariances and eigenvectors are limited. Based on statistical properties of scalar products between deterministic and complex random vectors, this work defines a statistically justified threshold to identify target-related features embedded in the sample eigenvectors, leading to an estimator for the signal-bearing eigenspace. It is shown that data projection into this signal …

Phase Transitions And In Situ Dynamics Of Crystal Grain Formation Of Alumina Nanotubes Templated By Vertically Aligned Carbon Nanotubes, L. F. Lampert, A. Barnum, S. W. Smith, J. F. Conley, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Phase transitions of amorphous alumina (a-alumina) nanotubes grown by atomic layer deposition and templated by carbon nanotubes were investigated with thermal annealing, transmitted Kikuchi electron diffraction, electron-irradiation-induced crystallization, X-ray diffraction, and X-ray photoelectron spectroscopy. The resulting, engineered alumina nanotube arrays demonstrate a large range of tunable phases that are vital for understanding how alumina nanotube arrays can be applied for uses within biotechnology, catalysis, and other academic and industrial uses.