Engineering Commons^™

Recovery Of Trace Organic Pollutants By Solvent Extraction And Freeze Concentration, William Chih-Wen Chang

Masters Theses

"The objective of this investigation was to evaluate the use of batch type solvent extraction and freeze concentration in recovering trace organic pollutants from water. The work was performed using a simplified water system containing known concentrations of phenol, and natural water systems collected from three sources (Meramec Spring, Gasconade River near Jerome, and Missouri River in Jefferson City) with different levels of pollution. The simplified water system was used to evaluate the effect of the number of extractions, solvent to sample ratio, extraction time, initial organic concentration, pH, and turbidity on solvent extraction; and the effect of volumetric concentration …

Optumr A Digital Computer Program To Cost Optimize A District Heat Piping Network To Remove Waste Heat From Nuclear Power Reactors, James Richard Hendricks

Masters Theses

"The thermal pollution problem of a nuclear reactor electrical generating facility can be eliminated if an economical, productive use for the waste heat can be found. The computer program presented here is designed to investigate the economic feasibility of utilizing this waste heat to heat buildings. The program optimizes a district heating network using the reactor's rejected heat and performs a comparative analysis with a selected conventional heat rejection system. The results indicate that the system is feasible only if the reactor can be sited relatively close (5 miles) to an urban center. Increasing national concern regarding thermal pollution and …

Numerical Solutions Of The Torsional Oscillations Of A Shaft-Flywheel System, Mahendrakumar Ramkrishna Patel

Masters Theses

"The application of the finite-difference technique, the Fourier transform, and the Laplace transform for the solution of a system governed by the one-dimensional wave equation is examined. A specific example consisting of a continuous shaft-flywheel system acted upon by an exciting torque applied at a specific section of the shaft is studied. The exact solution to this example is obtained using the classical method of superposition of modes, and is used as a reference to evaluate the accuracy (in terms of the rms error) and relative efficiency (based on computer time) of three approximate solution methods. A sinusoidal excitation was …

A Computer Simulation Of The Internal Ballistics Of Recoilless-Rifle Rocket Launchers, John Edd Mosier

Masters Theses

"A computer program has been developed to simulate the basic mechanics and gas dynamics associated with launching a solid propellant rocket from a recoilless rifle. This program, entitled "KICKIT," may be used to predict the performance and evaluate many of the pertinent design parameters of both conventional recoilless rifles and a recoilless rocket launcher system. This program is a valuable analytical tool which enables the designer either to optimize the system design or predict the behavior of the system under off-design conditions"--Abstract, Page ii.

A Study Of The Composite Action Of Light Gage Steel Deck And Concrete, Charles Sherman Bach Jr.

Masters Theses

"This thesis is on the investigation of corrugated light-gage steel sheets used as the tension reinforcement for concrete slabs. The steel sheets used had embossments placed at uniform intervals over the entire length of the sheets. The composite concrete and light-gage deck steel were tested to determine a method of design for this type of composite section from an economical, safe and practical standpoint. The investigation covered the flexural, shear and bond capacity of this type of composite section"--Abstract, page ii.

Initial Operation And Calibration Of The Umr Supersonic Axisymmetric Wind Tunnel, James Riley Murphy

Masters Theses

"Initial testing and a preliminary calibration were conducted in the UMR supersonic variable Mach number axisymmetric blowdown wind tunnel facility. During initial operations problems were encountered with control valve seat failure, control valve response and stability, and automatic operation. After having brittle fracture failures with seats made of nylon, Teflon and Telfon-copper composite, a copper seat was found to perform satisfactorily with minimal valve leakage. Control valve response and stability were greatly influenced by the setting of the needle valve located between the total pressure probe and the controller. The needle valve setting was observed to depend upon the stagnation …

Dynamic Analysis Of A Torsional Vibration Actuator, Narayandas Trikamdas Ashar

Masters Theses

"The objective of this study is the evaluation of a mechanical system, which includes a Hooke's joint, as a possible torsional vibration actuator. The essential requirement of such a system is to produce a periodically varying angular motion superimposed upon a mean constant speed rotation. The basic kinematics of a Hooke's joint suggest that it could be used to generate the type of motion desired. The mechanical arrangement of a system incorporating a Hooke's joint is described and the governing differential equations are developed. These equations are simultaneous, differential equations of second order and are highly nonlinear. Values of typical …

Voids In Neutron Irradiated Aluminum, Nicholas H. Packan

Doctoral Dissertations

"Void formation in high purity aluminum resulting from irradiation to fluences between 1.5 x 10¹⁹ and 1.6 x 10²² neutrons/cm² (E > 0 .1 MeV) at a temperature of 55 ± 5ºC was studied, primarily by means of transmission electron microscopy. In particular the effects of neutron fluence and flux were examined, as well as the possible influences of both preexisting and transmutation-produced impurities. A very low concentration of voids (about 10¹²/cm³) resulted from irradiation to 1.5 x 10¹⁹ neutrons/cm²; they averaged about 150 Å in diameter. Void concentrations and sizes increased with fluence, reaching values of 6 x 10¹⁴ voids/cm³ …

Transient Response Of A Vibration Isolation System, Hemendra Shantilal Acharya

Masters Theses

"A practical procedure for investigating the performance of a vibration isolation system under transient conditions is presented. For this investigation, an induction motor with an unbalanced rotor is studied during the period when it accelerates to its operating speed from rest. Using Newton's second law of motion, equations of motion are derived, first neglecting and then considering the effect of "inertia torque". This torque is produced by the inertia force resulting from vertical acceleration of the unbalanced mass. The equations are solved on a digital computer using the Runge-Kutta method of order 4. The results obtained are compared with those …

Investigation Of Liquid Carryover In The Girdler-Sulfide Process For Production Of Heavy Water At The Aec Savannah River Plant, Samuel Clark Allen

Doctoral Dissertations

"An investigation of the causes of liquid carryover in the Girdler-Sulfide process for the production of heavy water was carried out using 12 samples of carbon collected over a one-year time period. Organic impurities from the feedwater were concentrated by adsorption on carbon. Studies of methods for the drying of carbon showed that freeze drying resulted in the minimum reproducible moisture retention without gross loss of the adsorbed organic materials. Rotary vacuum evaporation and air drying of beds of carbon were proven to be less efficient. A study was made of the variables which affect extraction efficiency by the Soxhlet …

Simulation Of A Gas Storage Reservoir With Leakage By A Two-Dimensional Layered Mathematical Model, Steven William Ohnimus

Doctoral Dissertations

"A generalized mathematical model was developed for two-dimensional compressible fluid flow accounting for the effects of relative permeability capillary pressure, and gravity drainage in addition to the reservoir properties of rock heterogenity and reservoir geometry. The generalized model developed was applied to an aquifer gas storage reservoir in which vertical leakage occurred from the main reservoir to two adjacent overlaying zones. The experimental results of Thomas, et al. were utilized in applying the model to gas storage injection/withdrawal periods yielding reasonable results for the three layers"--Abstract, page ii.

An Sem Surface Study Of Nucleate Pool Boiling Heat Transfer To Saturated Liquid Nitrogen Reduced Pressures From 0.1 To 0.9, David Virgil Porchey

Doctoral Dissertations

"This study constituted an examination of both nucleate boiling and maximum heat flux characteristics of liquid nitrogen boiling from characterized surfaces. Several textures of gold plated copper surfaces were studied in addition to silver and silver oxide surfaces. Data were taken over a wide range of reduced pressures. All surfaces were examined using a Scanning Electron Microscope (SEM). Data and micrograph comparison revealed that both surface chemistry and surface roughness affect the nucleate boiling characteristics of liquid nitrogen. These effects are separated from each other showing that nucleate boiling is a function of both surface chemistry and topography. Surface roughness …

Diffusion And Internal Friction In Sodium-Rubidium Silicate Glasses, Gary L. Mcvay

Doctoral Dissertations

"The internal friction and self diffusion coefficients of sodium and rubidium ions for (1 - X) Na₂O·X Rb₂O·3 SiO₂ glasses have been measured. The diffusion measurements employed radioactive isotopes and a thin sectioning technique and extended from 350 to 500°C. Internal friction measurements were made from -150 to 500°C and at frequencies of 0.05 to 6000 Hz. The maximum height for the mixed alkali internal friction peak occurs at the composition where the sodium and rubidium diffusion coefficients are equal. It is concluded that the mechanism responsible for the mixed alkali peak is a cooperative rearrangement of sodium-rubidium ions and …

A Computer Simulation Of Mine Air Shaft Thermodynamics, Ambyo Sumopandhi Mangunwidjojo

Doctoral Dissertations

"Several earlier investigations have been conducted into various aspects of heat problems in underground mines. The application of general gas laws and thermodynamics in the approach of mine ventilation has been helpful in elucidating certain difficulties associated with the subject. By combining several of the techniques perfected by these researchers and applying Carrier's method of calculation for heat flow from exposed rock strata into a workable plan, a method was developed whereby it is possible to accurately and conveniently predict the quality of working environment at any point within a deep mine. The findings of this study may be of …

Effect Of Axial Dispersion On Interphase Mass Transfer In Packed Absorption Columns, Virendra Kumar Mathur

Doctoral Dissertations

"A steady state approach was followed in this investigation to determine the effects of liquid and gas flow rates, packing size and packing height on the interphase mass transfer coefficient and gas phase axial mixing Peclet numbers. Experiments were performed on the absorption of carbon dioxide from a mixture of carbon dioxide and nitrogen in a packed column. Absorption was performed using 1/4, 3/8 and l/2 inch Raschig rings, with a packing height of 3 feet and also using 3/8 inch Raschig rings with a packing height of 5 feet. The liquid and gas flow ranges used were 2865 to …

Use Of The Turbulence Kinetic Energy Equation In Prediction Of Nonequilibrium Turbulent Boundary Layers, William Madison Byrne Jr.

Doctoral Dissertations

"A differential method is proposed for the prediction of a broad range of turbulent boundary layers of engineering and scientific interest. A digital computer program is presented which is applicable to boundary layers with positive, negative, and zero pressure gradient in the main-stream direction as well as boundary layers with suction, blowing or zero mass addition at the wall. The turbulence kinetic energy equation is solved simultaneously with the longitudinal momentum and continuity equations to provide an independent means for determining the effective viscosity which makes allowance for "history" effects in the flow. It is shown that the prediction method …

An Investigation Of The Stiffness Of Shafts With Integral Disks, Richard King Riley

Doctoral Dissertations

"The results of an investigation of the effect of an integral disk on the torsional elastic stiffness of an axisymmetric shaft are presented. Various configurations of disk diameters and widths on a shaft of specified diameter were investigated, using a finite element method of calculation verified by experimentation. The finite element method is presented for the elastic solution of a general axisymmetric body under all possible axisymmetric load conditions. The axisymmetric body is idealized as an assemblage of triangular cross-sectioned torii representing both the normal and shear properties. The elastic stiffness is used to obtain the equilibrium equations of the …

Discrimination Of Signal And Noise Events On Seismic Recordings By Linear Threshold Estimation Theory, David Nuse Peacock

Doctoral Dissertations

"The object of this study is the investigation of a linear threshold element technique for identifying surface multiples on a single seismic trace. Traces of seismic events were generated which contained primaries, surface multiples, and various levels of Gaussian random noise. Since it was necessary to separate the events as much as possible, the traces were subjected to pulse-compression deconvolution processing prior to LTE analysis. Mean frequency, peak frequency, amplitude spectrum variance, periodicity, and polarity were employed as pattern parameters. A set of weights was found that would maximize the moment of inertia of the S line distribution of the …

Oxygen Uptake By The Benthal Sludge Of A Waste Stabilization Pond, Edward Landon Niedringhaus

Masters Theses

"This thesis describes the laboratory evaluation of the benthal sludge oxygen uptake of a 6.7 acre waste stabilization pond which has served a city of 2,400 population for a period of seven years. Special emphasis is directed toward the explanation of laboratory techniques developed for this study to measure the oxygen uptake rate. The effects on oxygen consumption of temperature, nature of sludge, initial oxygen tension, and sludge consolidation are discussed. Benthal sludge samples were taken from three locations in the pond. Oxygen consumption studies were conducted in a specially designed plastic cylinder which included a novel magnetic mixing system. …

Penetration In Granite By Shaped Charge Liners Of Various Metals, Hemendra Nath Kalia

Doctoral Dissertations

"The penetration in Missouri red granite by cylindrical charges with metal liners of aluminum 2011 (T-3), aluminum 7075 (T-6), yellow brass, monel, maraging steel (vascomax 250), and copper was measured. Metals having high ductility and moderate compressive strength penetrated deeper than high strength maraging steel. Aluminum required a greater standoff for optimum penetration than the other metal liners tested. Preliminary metallographic studies of the liner metals and slugs showed that the grains had elongated along the slug axis. The metals containing zinc formed very small or no slugs. The granite grains were highly fractured. The holes were discolored and coated …

Development And Application Of Cartesian Tensor Mathematics For Kinematic Analysis Of Spatial Mechanisms, Robert Myrl Crane

Doctoral Dissertations

"The complexity of spatial mechanisms in themselves and the absence of an attractive analytical tool for their study has left this field of engineering analysis largely unexplored. In recent years several analytic methods have emerged. One of the most attractive of these is the tensor method. Literature surveys reveal that the tensor method is largely unexploited in the U.S.A., with regard to spatial mechanisms as well as simpler kinematic problems. The purpose of this work is to develop tensor mathematics for application to the kinematic analysis of spatial mechanisms. Methods are developed for position solutions and the determination of velocities …

The Cathodic Reduction Of Maleic Acid, Show Yih Hsieh

Doctoral Dissertations

"The electrochemical reduction of maleic acid (0.0003 to 0.3 M) was studied on Hg, 0.5% Bi(Hg) amalgam, 5.0% Bi(Hg) amalgam, and Bi cathodes in 1 n H₂SO₄-K₂SO₄-KOH electrolytes (pH 0.3 to 4.0) at 60°C. The maleic acid was converted to succinic acid with high efficiencies (86 to 100%) on all cathodes. Polarization curves with linear Tafel sections were found. All the cathodes had similar kinetic parameters...A reaction mechanism consistent with the experimental observations is proposed..."--Abstract, pages ii-iii.

Electrode Reactions In Zinc Electrolysis, Ernest R. Cole

Doctoral Dissertations

"The effects of temperatures from 0°C to 50°C and current densities from 10 asf to 200 asf on the current efficiency in the electrolysis of pure zinc sulfate solutions (65 gpl Zn⁺⁺ - 200 gpl H₂SO₄) were determined. Pure platinum and platinum coated titanium anodes were used with an aluminum cathode. Platinum anodes were not inert at certain combinations of temperature and current density, and platinum acted as a low overvoltage impurity causing resolution of the cathode deposit. Orientation of the zinc deposits was found to vary with temperature and to have a distinct relationship to current efficiency. Preconditioning of …

Iddap -- Interactive Computer Assistance For Creative Digital Design, Richard Franklin Crall

Doctoral Dissertations

"A new computer-aided design program to assist in the initial phases of logical design is described. The program, intended for use via an on-line remote terminal, will allow the designer to study and experiment with design alternatives during the initial creative design phases. An ALGOL-like language is used for specifying the system being designed. In addition to simulating the design, the program allows the user to perform on-line design changes, reorganize data and generate timing diagram information"--Abstract, page ii.

Higher Space Mode Analysis Of A Large Cylindrical Pulsed H₂O System, Harold David Hollis

Doctoral Dissertations

"By utilizing a geometrically centered pulsed source internal to a large (B²_g) ≈ 0.002) cylindrical H₂O system, the neutron flux was measured as a function of position and time. A least square fit of the data yielded the fundamental and five higher decay constants and amplitudes of the thermal neutron flux. Symmetrical and enhanced neutron densities were obtained as a result of the internal source. Long waiting times were unnecessary and data acquisition was accelerated.

The decay constants were found to be independent of position, pulse width, counting time and rates, method of normalization, or waiting time. …

Synthesis Heuristics For Large Asynchronous Sequential Circuits, Robert Judson Smith

Doctoral Dissertations

"Many well-known synthesis procedures for asynchronous sequential circuits produce minimal or near-minimal results, but are practical only for very small problems. These algorithms become unwieldy when applied to "large" circuits with, for example, three or more input variables and twenty or more internal states. New heuristic procedures are described which permit the synthesis of very large machines. Although the resulting designs are generally not minimal, the heuristics are able to produce near-minimal solutions orders of magnitude more rapidly than the minimal algorithms. A method for specifying sequential circuit behavior is presented. Input-output sequences define submachines or modules. When properly interconnected, …

Model-Referenced Adaptive Control Of Plants With Noise And Inaccessible State Vector, Donald James Schooley

Doctoral Dissertations

"The problems of process noise, measurement noise, and inaccessible process state vector in the model-referenced system of Shackcloth-Butchart-Parks (SBP) are investigated. Since the system no longer possesses a static equilibrium point, the concept of asymptotic stability does not apply. However, by using Liapunov-like ideas, the error between the plant (process plus controller) and the model is shown to enter a region about the origin if certain bounds are known. A possible technique for reducing the size of this region is to feedback a function of the error into the plant's input. Several methods of circumventing the inaccessible state vector problem …

Binary Molecular Diffusivities In Liquids: Prediction And Comparison With Experimental Data, Ronald Dean Mitchell

Doctoral Dissertations

"The Eyring rate theory equation has been modified successfully to enable predictions of binary molecular diffusivities for a wide variety of liquid-liquid systems. The activation free energy for binary diffusion has been evaluated in terms of the activation free energies for self diffusion of the solvent and solute. This was accomplished through the use of regular solution theory by relating the bond breaking energy of the jump step to the bond breaking energy in evaporation. Diffusivities estimated by this equation and the equations developed by Olander, by Gainer and Metzner, and by Wilke and Chang were compared with experimental data. …

A Study Of The Design And Construction Of A Full Scale Aircraft Component Demonstration Fatigue Test, Stephen Andrew Wright

Masters Theses

"The objective of this project was to design and build a full scale demonstration fatigue test for a Piper Aztec stabilator. A general discussion of the construction is included in this report. The Fourier series method of the aerodynamic theory of spanwise loading was used to determine the load distribution. The results show a close relationship with data furnished by Piper Aircraft Corporation. Fatigue theory is discussed in order to provide background for fatigue testing. The test specimen, methods and procedures of testing, known loading methods and systems, safety, etc., are discussed. Federal requirements for regulating and testing of aircraft …

Spheroidization In Tool Steels, Sharad Gajanan Bankar

Masters Theses

"A carbon steel, W1, and four other alloy tool steels, namely, A2, H13, D3, and M2, were spheroidized by five different procedures. Any modification made in the treatments for an individual steel were suggested by the results obtained with these five procedures. The hardnesses and microstructures obtained were compared with steel samples annealed at a tool steel mill. The response given by different steels to various methods of spheroidization was studied. It was found that A2, W1, and D3 steels responded the best to the cycling method whereas the best response to the isothermal annealing was given by H13 and …