Engineering Commons^™

Are Natural Fractures In Sandstone Reservoir: Water Wet – Mixed Wet – Or Oil Wet?, Salah Almudhhi, Laila Abdullah, Waleed Al-Bazzaz, Saleh Alsayegh, Hussien Alajaj, Ralph E. Flori

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study accurately measures the wettability contact angle of native Kuwaiti sandstone reservoir that hosts mixed pore size distributions in both the tight sandstone matrix as well as the natural fracture (NF) embedded in it. Also, this study, effectively, investigates the geometrical size and shape of natural available voids whether matrix voids or NF voids captured in the rock 2D image frame system. Correspondingly, this study is, successfully, measure tight matrix, NF Pore wall, and NF pore opening wettability performance and recovery efficiency contributions inside the sandstone reservoir. A model pore/ grain contact angle wettability is generated. Therefore, this study …

Seismic Azimuthal Anisotropy Beneath A Fast Moving Ancient Continent: Constraints From Shear Wave Splitting Analysis In Australia, Kailun Ba, Stephen S. Gao, Jianguo Song, Kelly H. Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Seismic Azimuthal Anisotropy Beneath Australia is Investigated using Splitting of the Teleseismic PKS, SKKS, and SKS Phases to Delineate Asthenospheric Flow and Lithospheric Deformation Beneath One of the Oldest and Fast-Moving Continents on Earth. in Total 511 Pairs of High-Quality Splitting Parameters Were Observed at 116 Seismic Stations. Unlike Other Stable Continental Areas in Africa, East Asia, and North America, Where Spatially Consistent Splitting Parameters Dominate, the Fast Orientations and Splitting Times Observed in Australia Show a Complex Pattern, with a Slightly Smaller Than Normal Average Splitting Time of 0.85 ± 0.33 S. on the North Australian Craton, the Fast …

A Novel Technique For The Quantitative Determination Of Wettability Of A Severely Heterogeneous Tight Carbonate Reservoir, Saleh Al-Sayegh, Ralph E. Flori, Waleed Al-Bazzaz, Abdulaziz Abbas, Ali Qubian, Hasan Al-Saedi

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The objective of this study is to accurately measure the wettability contact angle of a cretaceous carbonate reservoir in a vertical well set-up known for as an unconventional tight carbonate oil reservoir. Also, to investigate the relative heterogeneity of these samples using digitally captured images; these images accurately capture natural pore-system in this carbonate rock samples and their wettability performance attributed towards building a vertical depth wettability/heterogeneity model. To capture, measure and model natural tight matrix static contact angle wettability in order to understand their new physics that will advance unconventional tight oil reservoir characterization. Entire vertical well depth reservoir …

Practical Imaging Applications Of Wettability Contact Angles On Kuwaiti Tight Carbonate Reservoir With Different Rock Types, Saleh Al-Sayegh, Ralph E. Flori, Waleed Al-Bazzaz, Sohaib Kholosy, Hasan Al-Saedi, Abdulaziz Abbas, Ali Qubian

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study focuses on a tight carbonate reservoir which is located in Northern Kuwait and is classified as an unconventional reservoir. A practical imaging technique of wettability contact angle (θ°) presents "big data" as well as relative-permeability (Krw and Kro) measurements. Also, modeling, through rock image technology, the vast well-documented grain/pore boundary morphology available inside fresh rock fragments have achieved good results. Conventional laboratory relative-permeability experiments are expensive and time-consuming. This study introduces a novel method to measure/calculate relative permeability through fast, less expensive, non-destructive, and environmentally friendly techniques of imaging technology. One tight carbonate reservoir is selected, imaged, processed, …

Investigating Pore Body, Pore Throat, Nano-Pore Wettability Preference In Several Unconventional Kuwaiti Carbonate Reservoirs, Saleh Al-Sayegh, Ralph E. Flori, Hussain Alajaj, Waleed Hussien Al-Bazzaz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study will investigate measuring the wettability contact angles of native unconventional tight carbonate as well as other unconventional pore system reservoir samples that hosts varied pore shapes and subsequent wettability contact angle distributions in both reservoir matrix and possible natural fractures. Also, the investigation will include validation of the grain/ pore-wall wettability regions and classify the natural wettability preference available inside pores of the rock and their overall wettability performance and recovery efficiency contributions. Further investigation will include modeling pore throat contact angle wettability, and to understand their new physics that will advance reservoir characterization and oil recovery improvement.

Kuwaiti Carbonate Reservoir Oil Recovery Prediction Through Static Wettability Contact Angle Using Machine Learning Modeling, Saleh Al-Sayegh, Ralph E. Flori, Waleed Hussien Al-Bazzaz, Hasan Al-Saedi, Mostafa Al-Kaouri, Ali Qubian

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The objective of this study is to predict EOR efficiencies through static wettability contact angle measurement by Machine Learning (ML) modeling. Unlike conventional methods of measuring static wettability contact angle, the unconventional digital static wettability contact angle is captured and measured, then (ML) modeled in order to forecast the recovery based on wettability distribution phenomenon. Due to success in big data collection from reservoir imaging samples, this study applies data science lifecycle logic and utilizes Machine Learning (ML) models that can predict the recovery through wettability contact angles and thus identify the treatment of oil recovery for a candidate reservoir. …

Temporal Lidar Scanning In Quantifying Cumulative Rockfall Volume And Hazard Assessment: A Case Study At Southwestern Saudi Arabia, Abdullah A. Alotaibi, Norbert H. Maerz, Kenneth J. Boyko, Ahmed M. Youssef, Biswajeet Pradhan

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Rockfalls and unstable slopes pose a serious threat to people and property along roads/highways in the southwestern mountainous regions of Saudi Arabia. In this study, the application of terrestrial light detection and ranging (LiDAR) technology was applied aiming to propose a strategy to analyze and accurately depict the detection of rockfall changes, calculation of rockfall volume, and evaluate rockfall hazards along the Habs Road, Jazan Region, Saudi Arabia. A series of temporal LiDAR scans were acquired at three selected sites. Our results show that these three sites have different degrees of hazard due to their geological differences. The mean volume …

Findings Report: Virtual Workshop On ‘Resilient Supply Of Critical Minerals’, Marek Locmelis, Angela D. Lueking, Michael S. Moats, Kwame Awuah-Offei, Lana Z. Alagha, Mark W. Fitch, Alanna Krolikowski, Shelby Clark

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Executive Summary
On August 2-3, 2021, the Thomas J. O’Keefe Institute for Sustainable Supply of Strategic Minerals at Missouri University of Science and Technology (Missouri S&T) hosted the NSF-funded virtual workshop ‘Resilient Supply of Critical Minerals’. The workshop was convened via Zoom and attracted 158 registrants, including 108 registrants from academia (61 students), 30 registrants from government agencies, and 20 registrants from the private sector. Four topical sessions were covered:

A. Mineral Exploration and Source Diversification.
B. Supply Chain and Policy Issues.
C. Improving Mineral Recycling and Reprocessing Technologies.
D. Technological Alternatives to Critical Minerals.

Each topical session was composed …

Characterization And Oil Recovery Enhancement By A Polymeric Nanogel Combined With Surfactant For Sandstone Reservoirs, Mustafa Mohammed Almahfood, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The characterization and enhanced oil recovery mechanisms of a nanosized polymeric cross-linked gel are presented herein. A negatively charged nanogel was synthesized using a typical free radical suspension polymerization process by employing 2-acrylamido 2-methyl propane sulfonic acid monomer. The synthesized nanogel showed a narrow size distribution with one peak pointing to a predominant homogeneous droplet size. The charged nanogels were also able to adsorb at the oil-water interfaces to reduce interfacial tension and stabilize oil-in-water emulsions, which ultimately improved the recovered oil from hydrocarbon reservoirs. In addition, a fixed concentration of negatively charged surfactant (sodium dodecyl sulfate or SDS) was …

Extraction And Visualization Of Orientation Data From Virtual Geologic Surfaces With Matlab®, Avery J. Welker, John Patrick Hogan, Andreas Eckert

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

High-resolution visualization of surfaces of geologic interest, at a multitude of scales, using 3D point cloud technologies provides an opportunity to analyze spatial relationships of surfaces using orientation data. We present a MATLAB® script that produces planar geologic attitude data (e.g., strike, dip, and dip-direction data) from 3D datasets (e.g., point clouds, 3D scanning). The method utilizes Cartesian coordinates of triangular planar surfaces and converts them into matrices of conventional geologic attitude data. Spatial relationships among data points can be investigated, using polar tangent diagrams, stereographic analysis, or geologic curvature analysis. We utilize this script to create "synthetic" graphical plots …

Modeling Land Subsidence Using Insar And Airborne Electromagnetic Data, Ryan G. Smith, R. Knight

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Land subsidence as a result of groundwater overpumping in the San Joaquin Valley, California, is associated with the loss of groundwater storage and aquifer contamination. Although the physical processes governing land subsidence are well understood, building predictive models of subsidence is challenging because so much subsurface information is required to do so accurately. For the first time, we integrate airborne electromagnetic data, representing the subsurface, with subsidence data, mapped by interferometric synthetic aperture radar (InSAR), to model deformation. By combining both data sets, we are able to solve for hydrologic and geophysical properties of the subsurface to effectively model the …

Explosive Dust Test Vessel Comparison Using Pulverized Pittsburgh Coal, Jacob Miller, Jay Schafler, Phillip R. Mulligan, Robert Eades, Kyle A. Perry, Catherine E. Johnson

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Explosions of coal dust are a major safety concern within the coal mining industry. The explosion and subsequent fires caused by coal dust can result in significant property damage, loss of life in underground coal mines and damage to coal processing facilities. The United States Bureau of Mines conducted research on coal dust explosions until 1996 when it was dissolved. In the following years, the American Society for Testing and Materials (ASTM) developed a test standard, ASTM E1226, to provide a standard test method characterizing the “explosibility” of particulate solids of combustible materials suspended in air. The research presented herein …

Spectral Analysis Of Surface Waves To Detect Subsurface Voids, Payman Hajiani, Neil Lennart Anderson, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Systems and methods for detecting a subsurface cavity. A source applies a force to ground under inspection and a plurality of sensors coupled to the ground detect resulting surface waves. A processor is configured to extract phase and frequency components of the acquired seismic data, identify a phase shift in surface waves in the ground under inspection based on the extracted phase and frequency components, and determine one or more physical characteristics of a subsurface cavity based on the identified phase shift

Experimental Investigation Of Fracture Width Limitations Of Granular Lost Circulation Treatments, Mortadha Al-Saba, Runar Nygaard, Arild Saasen, Olav Magnar Nes

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Drilling fluid losses into fractured shales is a major challenge. Lost circulation treatments are widely applied to mitigate the losses; however, the effectiveness of these treatments is affected by different physical properties of the used lost circulation materials (LCM). This paper presents an experimental investigation to study the effect of LCM type, concentration, particle size distribution, temperature, and LCM shape on the formed seal integrity, with respect to differential pressure, at different fracture widths. The overall objective of this study is to address the effectiveness of LCM treatments in sealing fractured shales, with specific application to the over consolidated Barents …

Modeling Of Gas Production From Shale Reservoirs Considering Multiple Transport Mechanisms, Chaohua Guo, Mingzhen Wei, Hong Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gas transport in unconventional shale strata is a multi-mechanism-coupling process that is different from the process observed in conventional reservoirs. In micro fractures which are inborn or induced by hydraulic stimulation, viscous flow dominates. And gas surface diffusion and gas desorption should be further considered in organic nano pores. Also, the Klinkenberg effect should be considered when dealing with the gas transport problem. In addition, following two factors can play significant roles under certain circumstances but have not received enough attention in previous models. During pressure depletion, gas viscosity will change with Knudsen number; and pore radius will increase when …

Clustering Data Of Mixed Categorical And Numerical Type With Unsupervised Feature Learning, Dao Lam, Mingzhen Wei, Donald C. Wunsch

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Mixed-type categorical and numerical data are a challenge in many applications. This general area of mixed-type data is among the frontier areas, where computational intelligence approaches are often brittle compared with the capabilities of living creatures. In this paper, unsupervised feature learning (UFL) is applied to the mixed-type data to achieve a sparse representation, which makes it easier for clustering algorithms to separate the data. Unlike other UFL methods that work with homogeneous data, such as image and video data, the presented UFL works with the mixed-type data using fuzzy adaptive resonance theory (ART). UFL with fuzzy ART (UFLA) obtains …

Characteristics Of Co₂ Sequestration In Saline Aquifers, Fang Yang, Baojun Bai, Dazhen Tang, Shari Dunn-Norman, David J. Wronkiewicz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Storage of CO₂ in saline aquifers is a viable option for reducing the amount of CO₂ released to the atmosphere. This paper provides an overall review of CO₂ sequestration in saline aquifers. First, the principles of CO₂ sequestration are presented, including CO₂ phase behavior, CO₂-water-rock interaction, and CO₂ trapping mechanisms. Then storage capacity and CO₂ injectivity are discussed as the main determinants of the storage potential of saline aquifers. Next, a site section process is addressed considering basin characteristics, reservoir characteristics, and economic and social concerns. Three main procedures are then …

Fault Growth And Propagation During Incipient Continental Rifting: Insights From A Combined Aeromagnetic And Shuttle Radar Topography Mission Digital Elevation Model Investigation Of The Okavango Rift Zone, Northwest Botswana, Baraka D. Kinabo, John Patrick Hogan, Eliot A. Atekwana, Mohamed G. Abdel Salam, Motsoptse P. Modisi

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Digital Elevation Models (DEM) extracted from the Shuttle Radar Topography Mission (SRTM) data and high-resolution aeromagnetic data are used to characterize the growth and propagation of faults associated with the early stages of continental extension in the Okavango Rift Zone (ORZ), northwest Botswana. Significant differences in the height of fault scarps and the throws across the faults in the basement indicate extended fault histories accompanied by sediment accumulation within the rift graben. Faults in the center of the rift either lack topographic expressions or are interpreted to have become inactive, or have large throws and small scarp heights indicating waning …

Natrolitite, An Unusual Rock -- Occurrence And Petrographic And Geochemical Characteristics (Eastern Turkey), Emin Ciftci, John Patrick Hogan, Hasan Kolayli, Emin Cadirli

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Very unusual rocks consisting of natrolite (>95 vol.%) ± pargasite (<5 vol.%) and rare albite (<1 vol. %) have been discovered in the Kop mountain range, eastern Turkey. We propose to call these rocks 'natrolitite' and 'pargasite natrolitite'. They were produced by Na Si metasomatism of dikes and stocks of diorite through replacement of the intermediate primary igneous plagioclase to produce natrolite. The metasomatic alteration produced concentric elliptical zones characterized by distinct mineral assemblages centered on intrusions of diorite. The Central Zone 1 consists of variably albitized diorite with preserved magmatic textures (albite ± andesine ± pargasite ± quartz). Transition Zone 2 comprises natrolite-bearing diorite (natrolite ± albite ± andesine ± pargasite ± calcite ± quartz). Marginal Zone 3 is a rock made up almost entirely of natrolite (natrolite ± pargasite ± albite ± calcite ± chlorite). Outer Zone 4 occurs along the boundary between the natrolitite and the surrounding serpentinite and consists of listvenite, a rock which comprises magnesite, quartz, calcite, mica, talc, and hematite, indicating a role for CO₂ in the metasomatic reactions, consistent with the presence of calcite in the alteration zones. Zone 5 consists essentially of brecciated serpentinite with numerous hydrothermal quartz veins and calcite veins. Whole-rock compositions document an increase in Na₂O, Al₂O₃, and H₂O from the core (central zone) to the margin while CaO, MgO, and SiO₂ decrease. Plagioclase abundance and composition also varies outwards from the central core rocks where it occurs as a primary magmatic phase (~95 vol.% An_41-38) …

Percussive Penetration Of Unconsolidated Granular Media In A Laboratory Setting, Leslie S. Gertsch

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This controlled study examined the feasibility of a simple percussive approach to drilling through unconsolidated regolith deposits on Mars. The experiments showed that the approach is feasible at the low power levels and low confining pressures used, and that the rate of impact is more important to the penetration rate than is the mass of the impactor (hammer). More massive impactors tend to lower energy efficiency, as they do in terrestrial pile-driving. Unexpectedly, penetration plotted against applied energy tends to cluster into parallel linear trends. Within a given cluster, penetration is very sensitive to applied energy, while between clusters, the …

Improving Database Quality Through Eliminating Duplicate Records, Mingzhen Wei, Andrew H. Sung, Martha E. Cather

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Redundant or duplicate data are the most troublesome problem in database management and applications. Approximate field matching is the key solution to resolve the problem by identifying semantically equivalent string values in syntactically different representations. This paper considers token-based solutions and proposes a general field matching framework to generalize the field matching problem in different domains. By introducing a concept of String Matching Points (SMP) in string comparison, string matching accuracy and efficiency are improved, compared with other commonly-applied field matching algorithms. The paper discusses the development of field matching algorithms from the developed general framework. The framework and corresponding …

Effect Of Water Ice Content On Excavatability Of Lunar Regolith, Leslie S. Gertsch, Robert Gustafson, Richard E. Gertsch

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The amount of water ice contained within prepared samples of JSC-1 lunar regolith simulant strongly affects the excavatability of the material. As part of a NASA Phase I SBIR project, load-penetration testing of JSC-1 lunar regolith simulant was performed at water ice concentrations ranging from zero to 11% by mass (approximately saturated), after compaction and cooling to simulate probable lunar conditions. After mixing dry JSC-1 simulant with the appropriate amount of water, the samples were individually compressed into containment rings under 48 MPa of pressure. Thermocouples embedded in the samples monitored internal temperature while they were cooled in a bath …

Hydrogeophysical Investigation At Luxor, Southern Egypt, Ahmed Ismail, Neil Lennart Anderson, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Over the past 35 years, the exposed stone foundations of the ancient Egyptian monuments at Luxor have deteriorated at an alarmingly accelerated rate. Accelerated deterioration is attributable to three principal factors: 1) excavation and exposure of foundation stone; 2) construction of the Aswan High Dam; and 3) changes in the regional groundwater regime. In an effort to better elucidate the hydrostratigraphy in the Luxor study area that extends from the River Nile to the boundaries of the Nile Valley and covers about 70 km², a geophysical/hydrological investigation was conducted. Forty Schlumberger vertical electrical soundings (VES), two approximately 6 …

Concrete Roughness Characterization Using Laser Profilometry For Fiber-Reinforced Polymer Sheet Application, Norbert H. Maerz, Poornima Chepur, John J. Myers, Justin Linz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The failure of a reinforced concrete member strengthened with fiberreinforced polymer (FRP) laminates may be caused by crushing of concrete, rupture of FRP laminates, or delamination of the FRP sheet. Therefore, the effectiveness and failure mode of FRP sheets applied to beams and columns is related to the degree of adhesion of the epoxy to the concrete surface. When a peeling or delamination failure can be avoided, a more effective engagement of the FRP sheet occurs, which results in more efficient use of the material. One of the principal factors affecting the bond behavior between the concrete and epoxy is …

Calibration Of Optical Digital Fragmentation Measuring Systems, Norbert H. Maerz, Wei Zhou

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Optical granulometry systems like WipFrag are required to measure fragments in situ. That is to say, the fragments are in piles where sorting takes place, where fragments are partially overlapped, and where fines may not be seen because they fall in and behind the coarser fragments, or where the fines are simply too small to be seen. As a result, optical systems tend typically to overestimate the size of the distribution, and underestimate the variability of the distribution. The wider the size distribution being measured, the more severe the problem is. This paper presents the results of a study that …

Magma Traps And Driving Pressure: Consequences For Pluton Shape And Emplacement In An Extensional Regime, John Patrick Hogan, Jonathan D. Price, M. Charles Gilbert

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The level of emplacement and final form of felsic and mafic igneous rocks of the Wichita Mountains Igneous Province, southwestern Oklahoma, U.S.A. Are discussed in light of magma driving pressure, lithostatic load, and crustal magma traps. Deposition of voluminous A-type rhyolites upon an eroded gabbroic substrate formed a subhorizontal strength anisotropy that acted as a crustal magma trap for subsequent rising felsic and mafic magma. Intruded along this crustal magma trap are the A-type sheet granites (length/thickness 100:1) of the Wichita Granite Group, of which the Mount Scott Granite sheet is typical, and smaller plutons of biotite bearing Roosevelt Gabbro. …

Optical Digital Fragmentation Measuring Systems -- Inherent Sources Of Error, Norbert H. Maerz, Wei Zhou

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Automated optical imaging systems of measuring fragmentation are increasingly being used in the mining, comminution, and materials handling industries. These methods have been well received in many of the industries involved. Considering that in many of these applications there are no alternative ways of sizing material, having even a rudimentary measurement of size distributions allows evaluations of explosive, blast design, detonator performance, crusher and milling performance, and material degradation due to transport.

Optical methods have inherent limitations, which reflect on accuracy, precision, and reproducibility of measurement results. This stems from the fact that there are myriads of variables, which affect …