Engineering Commons^™

Effects Of Downwash When Measuring Gas Concentration With Uav-Mounted Gas Sensors, Jacob Lane Brinkman

Doctoral Dissertations

"This research concludes that the downwash region of a rotary-wing unmanned aerial vehicle (UAV) does not produce pressure variations substantial enough to cause significant changes in density-based gas concentration measurements. US regulations evaluate gas concentration as a function of gas density, and accurate concentration measurements are critical for protecting health and safety, which means evaluation of actual downwash effects on measured gas concentration is essential.

During experimentation, the UAV was fixed to a stand in a sealed chamber filled with NOx (NO and NO₂) of constant concentration. The UAV rotors ran at hovering speeds, and gas concentrations were …

Investigation Of Anomalous Data Trends During Coal Dust Explosibilty Testing, Jacob Lee Miller

Doctoral Dissertations

Coal dust explosibility is a health and safety concern that has been a recognized hazard for over 100 years. Initial testing by the Author using a Siwek 20L apparatus recorded a secondary maximum pressure at higher dust concentrations (1,000-7,000g/m³) with Pulverized Pittsburgh Coal (PCC). Higher dust concentrations are beyond the typical ASTM E1226 testing procedure but are possible in mining and processing scenarios. No reference documents have been discovered that show a secondary maximum pressure at higher dust concentrations. Literature reviewed identified that once a coal dust concertation generates a peak pressure, the pressure remains constant or decreases …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Investigating The Focusing Effect Of Charge Geometry With Computer Simulations, Witness Plates, And High-Speed Videography, Kelly Ray Williams

Doctoral Dissertations

"Scaled distance is used to calculate a safe standoff radius from the detonation of a known mass of an explosive. It has been shown that varying only the geometry of the charge significantly overdrives regions of the blast wave potentially resulting in hazardous overpressure levels at scaled distance safe radii. Pressure transducers are used to measure overpressure surrounding spherical, cylindrical, and cubic charges to determine if bridge waves were formed at the edges between flat sides as seen in published studies of cylindrical charges. In the fireball field a witness plate is used to evaluate radial energy distribution with a …

Pressure Versus Impulse Graph For Blast-Induced Traumatic Brain Injury And Correlation To Observable Blast Injuries, Barbara Rutter

Doctoral Dissertations

"With the increased use of explosive devices in combat, blast induced traumatic brain injury (bTBI) has become one of the signature wounds in current conflicts. Animal studies have been conducted to understand the mechanisms in the brain and a pressure versus time graph has been produced. However, the role of impulse in bTBIs has not been thoroughly investigated for animals or human beings.

This research proposes a new method of presenting bTBI data by using a pressure versus impulse (P-I) graph. P-I graphs have been found useful in presenting lung lethality regions and building damage thresholds. To present the animal …

The Mechanics Of Precision Presplitting, Anthony Joseph Konya

Doctoral Dissertations

"Precision Presplitting is a widely used method of presplit blasting for the mining and construction industries. In recent years considerable effort has gone into the development of empirical equations based on field data to be able to better design the Precision Presplit for various rock types and structural environments. However, the most widely discussed theory about the mechanics of the presplit formation, that of shockwave collisions, does not appear to be applicable for this method of presplitting.

This research has disproven this theory based on insufficient magnitude of the shockwave from modeling with basic wave mechanics. Other authors have suggested …

The Behavior Of Suas Under Explosive Loading Conditions And Implications For Safe Operating Procedures, Ashok Em Sudhakar

Doctoral Dissertations

"Drones are increasingly being used for tasks previously unimagined and the beneficial uses are evolving. The United States Congress has envisioned the possible uses of drones for both combating and conveying explosive threats and other harmful and destructive activities. Congress' intent is reflected in new laws (2018) and policies (2019).

All civilian available Small Unmanned Aerial Systems sUASs (Drones), weighing less than 55 pounds, in the current market are not designed for operations in explosive environments. This first of a kind research focuses on further understanding of sUASs response to explosive loading and the public policy implications. This research measured …

The Influence Of Caprock On Blast Fragmentation Distribution, Matthew Kurtis Coy

Doctoral Dissertations

"This dissertation describes the development of a small-scale model of a caprock-laden quarry blast and discusses the results from that testing. The purpose of this testing was to provide insight into the reasons for poor caprock breakage during blasting.

Small-scale test blocks were poured using a weak mortar mix to represent a limestone formation at a small scale. A cold joint was created in the upper portion of the test specimens to represent the bedding plane that separates caprock and substrate layers in a caprock-laden limestone bench. The scale-model test blocks were blasted using detonating cord. The primary configuration for …

Modeling Explosive Lensing On A Cylindrical Body In Air: A First Step Towards Sealing An Underwater Offshore Oil Spill, Phillip R. Mulligan

Doctoral Dissertations

"In 2010, the British Petroleum (BP) Deepwater Horizon accident leaked oil into the Gulf of Mexico for 87 days. A fast response method that can seal an oil pipe and stop the release of oil is needed in order to prevent future oil leaks from turning into ecological and financial disasters. Explosives can serve this need.

This research examined how a circular implosive discontinuous explosive lens interacts with a cylindrical surface. The following research was designed to study the applicability of the Method this author developed to predict the peak pressure from multiple shockwaves converging on a centrally located cylinder. …

Analysis Of Effects Of Surface Roughness And Local Surface Imperfections On Measured Pressure, Laurin Ashley Bookout

Doctoral Dissertations

"When tests using pressure to characterize the performance or effects of an explosive are conducted in laboratory or other small scale, highly controlled settings, it is expected that any gages will be ideally mounted and there will not be any surface imperfections or roughness near the gage location. However, when explosive tests are scaled up, the test beds typically do not have perfect surfaces. Instead there may be rough surfaces with various types of geometry or situations where it is extremely difficult to get the gage flush mounted with a flat surface. In a time where tests with multiple replications …