Engineering Commons^™

Strain And Temperature Measurement From Distributed Fiber Optic Sensors In Performance-Based Fire Engineering, Yanping Zhu

Doctoral Dissertations

"Strain and temperature measurement of steel and concrete structures under fires is critical to the understanding of structural performance yet historically challenging due to a significant gap in measurement science. This Ph.D. study characterizes in six parts low-cost distributed fiber optic sensors and applies them to strain, and temperature measurements based on Rayleigh and Brillouin light scattering. The first part aims to quantify the Rayleigh scattering based measurement accuracy of distributed fiber optic sensors under a heating-holding load protocol and characterize the effect of polymer coating on the sensors as the polymer softens and melts at elevated temperatures. The second …

Experimental And Numerical Studies Of Novel Thermal Energy Storage Materials For Applications In Concrete And Energy Storage Systems, Wenyu Liao

Doctoral Dissertations

In this work, several types of novel thermal energy storage (TES) materials and composites are explored, and a series of numerical simulation models and experimental protocols are developed to evaluate the potentials of these materials to be applied in concrete, pavement, and thermal energy storage systems.

The first two types of novel TES materials/composites are at the micro-scale, which use micro diatomite (DE) and cenosphere (Ceno) as carriers of phase change material (PCM), respectively. The third type of novel TES material is at the macro-scale, utilizing lightweight sand (LWS) and lightweight coarse aggregate as carriers to load PCM. The last …

Use Of Portable Seismic Property Analyzer And Ground Penetrating Radar To Assess Bridge Decks, Samie Ramadan A Hamad

Doctoral Dissertations

The Montauk Bridge deck was assessed based on the portable seismic property analyzer and ground penetrating radar data. Based on the analysis of the portable seismic property analyzer data, it was determined that over 65% of bridge conditions were rated serious to poor condition with an average compressive strength of less than 2500 psi; less than 35% of bridge deck conditions were rated fair to good with an average compressive strength over 2500 psi. Based on ground penetrating radar data, it was determined that 72% of the bridge deck was in serious to poor condition, and only 28% of the …

Bond Behavior Of Advanced Fiber Reinforced Composite-Concrete Joints, Xingxing Zou

Doctoral Dissertations

“Externally bonding advanced composite materials to concrete structures is an effective way to improve their strength, ductility, and durability. The interfacial bond behavior is fundamental to understand the overall structural performance of concrete structures strengthened with advanced composite materials. This study includes a comprehensive investigation of the bond behavior of composite-concrete joints with different fiber reinforced composite types. First, a direct approach to determine the bond-slip relationship for fiber reinforced cementitious matrix (FRCM)-concrete joints based on fiber strain measurements was proposed. Then, an analytical solution to predict the full-range response of FRCM-concrete joints was derived by assuming a trilinear bond-slip …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Numerical And Experimental Analysis Of Local Buckling Of Axially Loaded Steel Tubes Confined By Concrete And Frp, Nicholas Colbert

Masters Theses

“The hollow core Fiber-Reinforced-Polymer (FRP) concrete circular-steel (HC-FCS) column consists of an outer circular fiber reinforced polymer (FRP) tube, an inner thin-walled circular steel tube concentrically aligned, and a concrete shell between them. Research has been performed on the performance of the member as a whole, but to date, there has been no investigation into the behavior of the steel tube confined in the column. 17 small-scale columns were tested under axisymmetric axial compressions applied directly to the steel tube under displacement control. The conducted parametric study examined the effects of diameter-to-thickness (D/t) ratio, concrete unconfined compressive strength, FRP thickness, …

Numerical Simulation Of Prestressed Precast Concrete Bridge Deck Panels Using Damage Plasticity Model, Wei Ren, Lesley Sneed, Yang Yang, Ruili He

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Advanced Sustainable Concrete Materials For Infrastructure Applications, Kaylea Ann Smith

Masters Theses

"This study was performed to examine the effects of cement replaced by high volumes of Class C fly-ash on durability characteristics of concrete up to 120 days. Specifically, this study investigates possibility of amending American Society for Testing and Materials (ASTM) to allow High Volume Fly-ash (HVFA) concrete to cure until later ages prior to testing instead of 28 days. Five mix designs were compared with varying fly-ash percentages from 0 to 70% (by total cementitious mass). No other additives were present in any of the five mix designs. Water-to-cementitious ratio (w/cm) and total cementitious material remained constant as 0.40 …

Study On Surface Permeability Of Concrete Under Immersion, Jun Liu, Feng Xing, Biqin Dong, Hongyan Ma, Dong Pan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this paper, concrete specimens are immersed in ultrapure water, to study the evolutions of surface permeability, pore structure and paste microstructure following the prolonging of immersion period. According to the results, after 30-day immersion, the surface permeability of concrete becomes higher as compared with the value before immersion. However, further immersion makes the surface permeability decrease, so that the value measured after 150-day immersion is only half that measured after 30-day immersion. The early increase in surface permeability should be mainly attributed to the leaching of calcium hydroxide, while the later decrease to the refinement of pore structure due …

Effects Of High Volume Fly Ash And Powder Activators On Plastic And Hardened Concrete Properties, Drew Alexander Davis

Masters Theses

This study was performed to examine the effects of high volumes of Class C fly ash modified by powder activators upon the plastic and hardened properties of concrete. In a companion study, five Missouri area cements and five Class C fly ashes were examined for incompatibilities, with the most and least reactive combinations being scaled up to full scale concrete testing. Two baseline concrete mixtures were examined, the only difference in mixtures being the sources of portland cement and fly ash. Fly ash replacement was examined at 50% and 70% replacement (by total cementitious mass). Three powder activators were used …

Using Coupled Eulerian And Lagrangian Grids To Model Explosive Interactions With Buildings, Braden Lusk, William P. Schonberg, Jason Baird, Robert S. Woodley, Warren Noll

Mining Engineering Faculty Research & Creative Works

This paper presents the development of a computational model that can be used to study the interactions between structures and detonating explosives contained within them. This model was developed as part of an effort to develop a rubble characterization model for use in AmmoSIM, an agent based urban tactical decision aid (UTDA) software for weapon-target pairing. The rubble pile created following the collapse of a building in a combat situation can significantly impact mission accomplishment, particularly in the area of movement and maneuver. The information provided by AmmoSIM will enable both platoon level and command center staff to make informed …

Semiempirical Electromagnetic Modeling Of Crack Detection And Sizing In Cement-Based Materials Using Near-Field Microwave Methods, Jagadish Nadakuduti, Genda Chen, R. Zoughi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Detection and characterization of cracks in cement-based materials is an integral part of damage evaluation for health monitoring of civil structures. Microwave signals are able to penetrate inside of dielectric materials (e.g., cement-based materials) and are sensitive to local, physical, geometrical, and dielectric variations in a structure. This makes microwave nondestructive testing and evaluation (NDT&E) techniques suitable for inspection and health monitoring of civil structures. Near-field microwave NDT&E techniques offer the added advantage of providing high spatial resolution, requiring simple hardware that may be portable, low power, fast, real time, and robust. Additionally, these techniques are noncontact and one-sided. Besides …