Engineering Commons^™

Interactive Water Vortex Exhibit, Simon Way, Emily Laing, Roqaya Naseri, Makenzie Kan

Mechanical Engineering

The San Luis Obispo Children’s Museum requested an interactive water vortex exhibit to both engage and entertain inquisitive guests, ages two to eight. The goal was to design and manufacture an exhibit that would educate its users on the fluid mechanics behind water vortices. They activate the mechanics by spinning a wheel, which is perceived as the catalyst to manipulate the flow of water to successfully create a whirlpool. Our team has created an interactive display that will enlighten young minds, providing the museum with an educational exhibit which shares a concept not currently taught by any other. Our project …

Building Structures From Mycelium, Noah M. Brown

Physics

The purpose of this project was to develop a method for creating bricks from mycelium and agricultural waste. The bulk of the research happened in two parts, the first part being a period in which different substrates, strains, and methods were used build the bricks. This research took place in San Luis Obispo and was aided by a group of students in PSC392 under Dr. Pete Schwartz in early 2022. After developing a method for constructing these bricks, the research was moved to St. Thomas, Jamaica, in collaboration with an ecovillage called The Source Farm from July to September. The …

An Inexpensive Maximum Power Point Tracking System For An Insulated Solar Electric Cooker Using An Off-The-Shelf Buck Converter, Andrew A. Perez

Physics

A specialized control circuit using an off-the-shelf buck converter is built for an Insulated Solar Electric Cooker (ISEC). Cost and efficient power delivery are the focus. An ISEC is synonymous to a direct load heat resistor, allowing a specific maximum power point tracking (MPPT) algorithm and fewer components. Only a microcontroller, voltage sensor, and digital-to-analog converter are used with the buck converter to maximize the power delivered by a 100W solar panel for the 3.3Ω load.

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Solid Thermal Storage As An Energy Storage Device In Insulated Solar Electric Cookers: Thermal Modeling And Experiment, Michael Antonio Fernandez

Physics

The use of solid thermal storage (STS) as an energy storage device in insulated solar electric cookers (ISEC) was explored using a thermal simulation before retrofitting an existing cooker without energy storage and testing it under several conditions. STS sizing, material selection, and geometry were examined from both theoretical and practical perspectives and re-examined following experimental results. Characterization of the system’s thermal interfaces and methods to improve their thermal conductivities were investigated resulting in several performance enhancements to the system.

Maximum Trapping Focal Length In Photophoretic Trap For 3d Imaging Systems, Jason M. Childers

Electrical Engineering

This product is a photophoretic trapping system which allows varying focal lengths to test which focal lengths are possible for trapping toner particles. This system establishes that there exists a maximum trapping distance limitation and is the first time the effect of focal length is studied in a photophoretic trapping system. Increasing photophoretic trapping focal length is necessary for improving this technology as a 3D display. The 3D imaging technology is realized by dragging a microscopic (micrometer-scale) particles with a laser beam to trace an image. This technology can display fully colored and high-resolution 3D images visible from almost any …

Interactive Physics Display: Air Cannon, Marina Smeltzer, Sydney Hosokawa, Jordan Nguyen, Jessica Ouyang

Mechanical Engineering

The San Luis Obispo Botanical Garden (SLOBG) is a non-profit organization that provides a place for visitors to connect with and explore nature. The sponsors from SLOBG sought an interactive physics display to be implemented in their children’s garden that will educate children and adult visitors about physics concepts in a welcoming and comfortable atmosphere. The research done showed that customers are looking for a “wow” factor with the display to surprise and engage them. Patents showed the design and build of interactive playground equipment. Government reports described the curriculum for the target audience and also outlined the safety precautions …

Soarnet, Deep Learning Thermal Detection For Free Flight, Jake T. Tallman

Master's Theses

Thermals are regions of rising hot air formed on the ground through the warming of the surface by the sun. Thermals are commonly used by birds and glider pilots to extend flight duration, increase cross-country distance, and conserve energy. This kind of powerless flight using natural sources of lift is called soaring. Once a thermal is encountered, the pilot flies in circles to keep within the thermal, so gaining altitude before flying off to the next thermal and towards the destination. A single thermal can net a pilot thousands of feet of elevation gain, however estimating thermal locations is not …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Direct Drive Solar Panel Control Circuit, Marcorios Bekheit

Physics

A control circuit is built for insulated solar electric cookers (ISEC). Power delivery and temperature safety are the focus. Using a maximum power point tracking (MPPT) algorithm, Arduino Nano, voltage and current sensors, and a buck converter, the solar panel’s output power was maximized for a direct load heat resistor with 3.5Ω for a range of solar intensities. Using a resistance temperature detector, a temperature sensor is built for safety shutoff.

Comparing Radiation Shielding Potential Of Liquid Propellants To Water For Application In Space, John Czaplewski

Master's Theses

The radiation environment in space is a threat that engineers and astronauts need to mitigate as exploration into the solar system expands. Passive shielding involves placing as much material between critical components and the radiation environment as possible. However, with mass and size budgets, it is important to select efficient materials to provide shielding. Currently, NASA and other space agencies plan on using water as a shield against radiation since it is already necessary for human missions. Water has been tested thoroughly and has been proven to be effective. Liquid propellants are needed for every mission and also share similar …

Cooking Systems Using Aluminum Foam, Ryan Tetsuo Mizukami

Physics

In developing countries, the use of wood burning fires for cooking is cause for illness and death. With this in mind, research was conducted to develop a solar cooking device capable of cooking of soup within 15 mins in order to reduce the negative impacts of cooking with wood. Current methods of solar-based cooking, such as solar concentrators and solar tube ovens, are impractical. A small solar panel is a cost-effective way to produce energy but will not produce enough power to cook within a reasonable amount of time. Even if it is assumed that all of the energy produced …

Mechani-Kits Senior Design Project, Jake Utley, Sophie Carson, Vincent Seguin

Mechanical Engineering

Studies suggest that when designed and executed well, hands-on activities can enhance student understanding of key mechanics concepts. Current products are expensive and typically not designed to meet a variety of learning objectives. Through the Mechanics of Inclusion and Inclusivity in Mechanics grant, the Cal Poly Physics and Engineering Departments are seeking to incorporate new hands-on activities into their courses. Our team has designed three inexpensive ”MechaniKits” to be used in physics, statics and dynamics courses [1]. This Final Design Review outlines our findings, objectives, and final designs for this project. It also explains our manufacturing and design verification plans. …

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

Design Of A 5 Degree Of Freedom Kinematic Stage For The Dual Crystal Backlighter Imager Diagnostic, Nicholas Nguyen

Master's Theses

The National Ignition Facility (NIF) is home to the world’s most energetic laser. The facility is one of the leading centers in inertial confinement fusion (ICF) experiments to research and understand sustainable fusion energy. To fully document and understand the physics occurring during experiments, precise diagnostics are used for a wide range of purposes. One diagnostic, the crystal backlighter imager (CBI), allows for X-ray imaging of the target at late stages of its implosion.

The aim of this project was to increase the current capabilities of the CBI diagnostic with the addition of a second crystal. This thesis focuses on …

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.

Optimizing Llrf Parameters In The Electron-Ion Collider, William M. Bjorndahl

Physics

To improve particle interaction in the future Electron-Ion Collider (EIC), we investigated different feedback implementations to control the accelerating voltage and examined the power and beam phase for each instance. Using MATLAB, we studied three feedback mechanisms: Direct, One Turn, and Feedforward. Enacting feedforward yielded the best performance. To minimize the klystron power consumption, we analyzed different Low-Level Radio Frequency (LLRF) parameters such as detuning. Combining theory and simulated results, we found the optimal detuning value that minimizes klystron power consumption.

A Rotating Aperture Mask For Small Telescopes, Edward L. Foley

Master's Theses

Observing the dynamic interaction between stars and their close stellar neighbors is key to establishing the stars’ orbits, masses, and other properties. Our ability to visually discriminate nearby stars is limited by the power of our telescopes, posing a challenge to astronomers at small observatories that contribute to binary star surveys. Masks placed at the telescope aperture promise to augment the resolving power of telescopes of all sizes, but many of these masks must be manually and repetitively reoriented about the optical axis to achieve their full benefits. This paper introduces a design concept for a mask rotation mechanism that …

An Investigation Of The Anomalous Thrust Capabilities Of The Electromagnetic Drive, Hannah J. Simons

Physics

The Electromagnetic Drive (EMDrive) is a propellant-less engine concept hypothesized by aero- space engineer Roger Shawyer. Shawyer’s proposed thruster technology is grounded on the theory of electromagnetic resonant behavior exhibited by a radiofrequency cavity, though the source of any generated thrust is undetermined by current physical laws. NASA Eagleworks Laboratories at John- son Space Center conducted a vacuum test campaign to investigate previously reported anomalous thrust capabilities of such a closed radiofrequency cavity, using a low-thrust torsion pendulum. The team published positive, although small-scaled thrust results in 2017. Following NASA Eagleworks breakthrough result and operating under the assumption that the …

Daily And Seasonal Variability Of Offshore Wind Power On The Central California Coast And Statewide Demand, Matthew Douglas Kehrli

Physics

No abstract provided.

Resistance Temperature Detectors In A Cryostat Refrigeration System, Kirsten Marie Manahan, Alice Callen

STAR Program Research Presentations

The Large Synoptic Survey Telescope (LSST) is a ground-based telescope that will survey the Southern sky every few nights. Located in the telescope will be a 3.2 gigapixel digital camera. To ensure proper instrumentation of the camera, there must be a monitored stable temperature. As part of my research, I assembled resistance temperature detectors and tested them to verify their reliability in measuring temperature in the camera’s cryostat refrigeration cooling system. Resistance temperature detectors function by the principle of thermal resistivity, in which their electrical resistances vary as temperature varies. Through testing, I was able to determine whether these particular …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

A High Quality, Eulerian 3d Fluid Solver In C++, Lejon Anthony Mcgowan

Computer Science and Software Engineering

Fluids are a part of everyday life, yet are one of the hardest elements to properly render in computer graphics. Water is the most obvious entity when thinking of what a fluid simulation can achieve (and it is indeed the focus of this project), but many other aspects of nature, like fog, clouds, and particle effects. Real-time graphics like video games employ many heuristics to approximate these effects, but large-scale renderers aim to simulate these effects as closely as possible.

In this project, I wish to achieve effects of the latter nature. Using the Eulerian technique of discrete grids, I …

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

Multispectral Identification Array, Zachary D. Eagan

Computer Engineering

The Multispectral Identification Array is a device for taking full image spectroscopy data via the illumination of a subject with sixty-four unique spectra. The array combines images under the illumination spectra to produce an approximate reflectance graph for every pixel in a scene. Acquisition of an entire spectrum allows the array to differentiate objects based on surface material. Spectral graphs produced are highly approximate and should not be used to determine material properties, however the output is sufficiently consistent to allow differentiation and identification of previously sampled subjects. While not sufficiently advanced for use as a replacement to spectroscopy the …

Optimizing The Telescope Assembly Alignment Simulator For Sofia, Zoe E. Sharp, Alex Quyenvo, Jennifer Briggs, Brian Eney

STAR Program Research Presentations

The Stratospheric Observatory for Infrared Astronomy (SOFIA) conducts research on a modified Boeing 747sp aircraft. By using a variety of infrared science instruments mounted on a 2.7 meter telescope, researchers can make discoveries about the galactic center, star formation, and various topics associated with a deeper understanding of our universe. To efficiently collect data through the SOFIA instruments, the instruments must be tested and prepared prior to being placed on the aircraft. Therefore, with the use of the Telescope Assembly Alignment Simulator (TAAS), researchers can design and construct improvements needed for these instruments to efficiently perform while in flight. The …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Design And Fabrication Of Liquid Scintillator Counter, Andrea Calderon Saucedo, John L. Orrell

STAR Program Research Presentations

Pacific Northwest National Laboratory (PNNL) is currently developing an ultra-low background liquid scintillator counter (ULB LSC) in the shallow underground laboratory. At a depth of 35-meters water-equivalent, the underground laboratory has a multi-layered shielding to keep out cosmic-ray induced background. The ULB LSC, which is located in a clean room facility, is a multi-layered design made up of various materials, including plastic scintillator veto panels, borated polyethylene, lead and copper. These layers help lower the contributions of the terrestrial background and intrinsic background, resulting from the impurities present in the materials, to the overall background count rate observed by the …

Visualizing Relationships Between Related Variables: Improving Physics Education Through D3.Js Network Visualizations, Stephanie Friend

Liberal Arts and Engineering Studies

phiMap is a web application started by Cal Poly professors and students to aid professors in teaching physics. I developed Javascript visualizations for phiMap that serve to simplify the processes of both teaching and learning physics. These visualizations aim to present relationships between physics variables in an easy to understand manner, and they could eventually have a huge impact on physics education.