Engineering Commons^™

Synthesis Of Multi-Wall Carbon Nanotubes Using Unseeded Hydrocarbon Diffusion Flames, Kozo Saito, Forman A. Williams, Alvin S. Gordon, Liming Yuang

Mechanical Engineering Faculty Patents

A method is provided for synthesizing carbon nanotubes from unseeded methane-air diffusion flames. A novel stainless steel and Ni—Cr wire probe is also provided for collecting carbon nanotubes from those diffusion flames.

A Note On Grashof Theorem, Wen-Tung Chang, Chen-Chou Lin, Long-Iong Wu

Journal of Marine Science and Technology

In this paper, Grashof’s theorem is justified from the perspective of the occurrence of stationary configurations and uncertainty configurations of four-link chains. The link length relations at stationary configurations and uncertainty configurations are examined in detail based on the triangle inequality, and then the conditions for the existence of a crank and a change point are deduced.

Laminar Film Condensation On A Horizontal Plate In A Porous Medium With Surface Tension Effects, Tong-Bou Chang

Journal of Marine Science and Technology

The problem of steady filmwise condensation on a finite-size horizontal plate embedded in a porous medium is studied for the case in which a cold plate faces upwards with a dry saturation vapor. Due to the effects of surface tension forces, there is a two-phase zone lying between the liquid film and the vapor zone. As in classical filmwise condensation problems, it is assumed that; (a) the inertia within the liquid film is negligible, and (b) the properties of porous medium, dry vapor, and condensate are constant. A dimensionless parameter Boc is introduced to characterize liquid flow due to surface …

Analysis Of Indentation Loading Of Cortical Bone Using Acoustic Emission Techniques, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

In this study, we recorded the number of Acoustic emission (AE) hits and related AE energy during indentation fracture of cortical bone using a PAC PCI-2 card and pico sensor. A threshold value of 43dB was used to filter premature trigger due to background noise. Registered AE hits had more than one count (threshold crossing). Amplifier gain was set at 40dB with a (0.1-1) MHz band pass filter. 8mm cubes of cortical bones were indented in the longitudinal direction at constant crosshead speed of 1 mm min-1 using a large 2D, 50˚ wedge indenter. We hypothesised that signals occurring as …

College Of Engineering Senior Design Competition Fall 2005, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Self Consistent Bathymetric Mapping Using Sub-Maps: Survey Results From The Tag Hydrothermal Structure, C. Roman, R. Reves-Sohn, H. Singh, S. Humphris

Christopher N. Roman

The spatial resolution of microbathymetry maps created using robotic vehicles such as ROVs, AUVs and manned submersibles in the deep ocean is currently limited by the accuracy of the vehicle navigation data. Errors in the vehicle position estimate commonly exceed the ranging errors of the acoustic mapping sensor itself, which creates inconsistency in the map making process and produces artifacts that lower resolution and distort map integrity. We present a methodology for producing self-consistent maps and improving vehicle position estimation by exploiting accurate local navigation and utilizing terrain relative measurements. The complete map is broken down into individual "sub-maps'', which …

Fully Compliant Tensural Bistable Micro-Mechanisms (Ftbm), D. L. Wilcox, Larry L. Howell

Faculty Publications

A new class of bistable mechanisms, the fully compliant tensural bistable micromechanism (FTBM) class, is introduced. The class consists of linear bistable micromechanisms that undergo tension loads, in addition to the bending loads present, through their range of motion. Proof-of-concept designs fabricated in two different microelectromechanical systems (MEMS) surface micromachining processes were demonstrated. Three sets of refined designs within the FTBM class were designed using optimization methods linked with nonlinear finite element analysis (FEA), then fabricated and tested. Measured force and displacement performance are compared to values obtained by FEA. On-chip actuation of the bistable mechanisms was achieved using thermomechanical …

Top-Down Structure And Device Fabrication Using In Situ Nanomachining, Xiaodong Li, Xinnan Wang, Qihua Xiong, Peter C. Eklund

Faculty Publications

We demonstrate the potential of an alternative tool for the fabrication of nanoscale structures and devices. A nanoindenter integrated with an atomic force microscope is shown to be a powerful machine tool for cutting precise length nanowires or nanobelts and for manipulating the shortened wires. We also demonstrate its utility in cutting grooves and fabricating dents (or periodic arrays of dents) in ZnSnanobelts. This approach permits the direct mechanical machining of nanodevices that are supported on a substrate without the inherent complications of e beam or photolithography.

A Detailed Approach For Concept Generation And Evaluation In A Technology Push Product Development Environment, Andrew Nelson

Theses and Dissertations

Many companies rely on successful product development as a means to increase their revenues and expand their operations. Market pull, the most common form of product development, begins with a specific customer, and focuses on how to satisfy that customer's needs. Technology push is a product development process where a technology is first discovered, then embodied in products that may be marketed to specific customers. Technology push presents several obstacles not encountered in market pull processes, such as a lack of a defined market, lack of established processes and difficulty in execution. These complications keep technology push from being more …

Characterisation Of Porous Materials Viscoelastic Properties Involving The Vibroacoustical Behaviour Of Coated Panels, Olivier Doutres, Nicolas Dauchez

Olivier Doutres Ph.D.

Porous materials are widely used as passive acoustic absorbers. For optimal design, it is often necessary to know the viscoelastic properties of these materials in the frequency range relevant to their application. The viscoelastic properties are obtained by fitting an analytical model to acoustical radiation experimental measurements carried out on a circular coated plate clamped in a rigid baffle. Compared with quasistatic method, the viscoelastic properties are here achieved at high frequency corresponding to the first resonance in the thickness of the porous layer and coupling between porous materials and external fluid is taken into account. The analytical model, developped …

Ole Miss Engineer 2005

Ole Miss Engineer

No abstract provided.

A K-Epsilon Extension For Wall-Bounded Flows On The Broadband Aeroacoustic System Simulator, David González

Masters Theses

The turbulence modeling capabilities of the Broadband Aeroacoustic System Simulator (BASS), an experimental code developed at NASA Glenn Research Center, have been extended to include wall-bounded flow capabilities. This was done by first validating the code's viscous solving routines by comparing numerical solutions to known, simple analytic solutions. Finally, the dynamics of the wall shear flows were accounted for with the use of wall-damping functions incorporated into the turbulence model. The results for both viscous and turbulence routines agree well with published data.

Composite Mechanical Property Enhancement Through The Use Of Y-End Shaped Short Fibers, Jin Tan

Theses and Dissertations - UTB/UTPA

This study uses Finite Element Analysis (FEA) to predict the mechanical property enhancement of the composites reinforced by end-shaped short fibers with different aspect ratios and volume fractions at microscale. Fibers used include conventional straight short fibers (CSSF), dumbbell-end shaped short fibers (DSSF), bone-end shaped short fibers (BSSF) and Y-end shaped short fibers (YSSF) with various lengths and angles. The critical distances between neighboring fiber ends for FEA modeling were theoretically deduced and numerically verified. This study has never been done before and the results fill a gap to this field.

In conclusion, planar-end Y-shaped short fiber reinforced composites showed …

Mixing Flow Structures Of Scalloped, Forced Lobed Mixers Using Piv And Plif Measuring Techniques, Nathan J. Cooper

Masters Theses

An Experimental study of internal forced lobed mixers similar to those used in jet aircraft engines is performed using whole field species concentration and velocity measuring techniques. Planar temperature and velocity measurements using Planar Laser Induced Fluorescence (PLIF) and 2D Particle Image Velocimetry (PIV) are performed for lobed, lobed scalloped and splitter mixers in aqueous solution. Specific emphasis is given to study scallops or notches cut into the mixer trailing edge and their role in mixing enhancement. Mixing is compared through velocity and species concentration measurements on axial and streamwise planes for the three dimensional, forced mixers in a confined …

Ductile Regime Nano-Machining Of Silicon Carbide, Biswarup Bhattacharya

Masters Theses

This thesis describes experimental work carried out to study the ability to ductile . single point diamond turn both polycrystal Silicon Carbide (SiC) and chemically vapor deposited (CVD) SiC. A Precitech diamond turning machine was used for ductile regime machining of polycrystal SiC at depths of 10 and 25 nm. The possibility of machining SiC in the ductile mode was substantiated by post process analysis of the chips collected during machining and the surface profiles. The force data obtained during machining was recorded and compared later with the different depth of cuts. An investigation into the ability to single point …

Determination Of Stiffness Matrix Of Tapered Roller Bearings For Vibration Models, Jeeva Kumar

Masters Theses

The stiffness matrix of tapered roller bearings under radial and axial load conditions was evaluated using an analytical model and an experimental approach. An experimental test system was designed and manufactured to determine the radial stiffness of the bearing under combined axial and radial load conditions. A second fixture was designed to measure the stiffness of the bearing under pure axial load conditions. The stiffness coefficients determined have been compared with those obtained from the analytical model, OEM (Original Equipment Manufacturer) data and ABAQUS model (finite element analysis software).

Effect Of Gender On Lower Extremity Kinematics During Rapid Direction Changes: An Integrated Analysis Of Three Sports Movements, S. G. Mclean, K. B. Walker, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Anterior cruciate ligament (ACL) injury is a common sports injury, particularly in females. Gender differences in knee kinematics have been observed for specific movements, but there is limited information on how these findings relate to other joints and other movements. Here we present an integrated analysis of hip, knee and ankle kinematics across three movements linked to non-contact ACL injury. It was hypothesised that there are gender differences in lower extremity kinematics, which are consistent across sports movements. Ten female and ten male NCAA basketball players had three-dimensional hip, knee and ankle kinematics quantified during the stance phase of sidestep, …

Performance Measurements Of Direct Air Injection In A Cavity-Based Flameholder For A Supersonic Combustor, Scott G. Edens

Theses and Dissertations

For several years the Air Force Research Lab Propulsion Directorate has been studying the difficulties in fueling supersonic combustion ramjet engines with hydrocarbon based fuels. Recent investigations have focused on the use of direct air injection into a directly-fueled cavity-based flameholder. Direct air injection has been shown qualitatively to be a valuable tool for improving cavity combustion. Little quantitative data is available that characterizes the performance of cavity-based flameholders. The objective of this research was to quantitatively determine the specific advantages and disadvantages of the direct air injection scheme. This was accomplished via intrusive probing into a supersonic free stream …

A Numerical Study Of Curved Labyrinth Seals For Steam Turbines, Sricharan Kishore Ayyalasomayajula

Masters Theses

A numerical experiment has been conducted to study and evaluate the structural behavior of newly designed labyrinth seals. Structural analysis was performed to understand, evaluate and compare new seals with a baseline straight seal that is typical of commonly used seals in steam turbines. New configurations of labyrinth seal knives were developed for use in steam turbines [17]. The main objective of this study is to develop a better understanding of selected various labyrinth seals that may be configured to minimize the steam leakage and reduce seal interactions with the shaft. Computational fluid dynamic modeling of the various configurations, from …

Topology Optimization Of Carbon Nanotube Reinforced Polymer Damping Structures, Seshadri Mohan Varma Damu

Masters Theses

Topology optimization has been successfully used for improving vibration damping in constrained layer damping structures. Reinforcing carbon nanotubes in a polymer matrix greatly influence the mechanical properties of the polymer. Such nanotube-reinforced polymers (NRP) can be used to further enhance the damping properties of the constrained layer structures. In this work, topology optimization is performed on constrained damping layer structures using NRP in order to maximize the loss factor for the first resonance frequency of the base beam. In addition to the material fractions of the NRP and elastic material, the volume fraction of the nanotubes in the polymer is …

Preliminary Design Approach For Prosthetic Ankle Joints Using Compliant Mechanisms, Jason Matthew Wiersdorf

Theses and Dissertations

The objective of this thesis is to develop design approaches and models for prosthetic ankle joints using kinematic models of the human ankle and compliant mechanisms technology. Compliant mechanisms offer several potential design advantages over traditional rigid-body designs including high reliability and low cost. These design advantages are ideal for use in prosthetics. Some prosthetic ankle/foot systems currently on the market have multiple degrees of freedom yet are expensive. Additionally, even though these systems have multiple degrees of freedom, none of them are designed after the actual movements of the biological ankle. In this thesis a two, single degree-of-freedom hinge …

Broadband Coherent Anti-Stokes Raman Scattering Spectroscopy Of Nitrogen Using A Picosecond Modeless Dye Laser, Sukesh Roy, Terrence R. Meyer, James R. Gord

Terrence R Meyer

Broadband picosecond coherent anti-Stokes Raman scattering (CARS) spectroscopy of nitrogen is demonstrated using 145-ps pump and probe beams and a 115-ps Stokes beam with a spectral bandwidth of 5 nm. This is, to our knowledge, the first demonstration of broadband CARS using subnanosecond lasers. The short temporal envelope of the laser pulses and the broadband spectral nature of the Stokes beam will enable nonresonant-background-free, single-shot, or time-dependent spectroscopy in high-pressure or hydrocarbon-rich environments. Successful correlation of room-temperature broadband picosecond N2 CARS with a theoretical spectrum is presented.

A Gasless Method Of Spraying Thermoplastic Resin, Dan T. Rogers

Theses and Dissertations

This spraying method for thermoplastic resins is a new manufacturing process for applying thermoplastics to a mold or surface in an efficient way that has the potential of reducing cycle time. Spraying thermoplastic resins is similar to spraying other polymers, such as paint, with the differences being higher pressure and temperature. This method uses an injection molding machine with a modified nozzle to spray the plastic material. In this study, temperature, pressure, and nozzle size were factors that influenced the success of this spraying method. The method of spraying in this study proved spraying without a gas is possible, a …

Object Oriented Cae Software For The Exploration And Design Of Microstructures, Stephen D. Sintay

Theses and Dissertations

Through the use of generalized spherical harmonic basis functions a spectral representation is used to model the microstructure of cubic materials. This model is then used to predict the macroscopic elastic and plastic properties of materials with cubic crystal symmetry and various sample symmetry including triclinic and axial—symmetric. Building on the work of citeN{Barnett-FractureMechanics} the influence that anisotropy has on the fatigue response of the material is also modeled. This is accomplished through using the effective elastic stiffness tensor in the computation of crack extension force G. The resulting material model and macroscopic property calculations are the foundation for …

Recovery Of The Grain Boundary Character Distribution Through Oblique Double-Sectioning, Brent L. Adams, David T. Fullwood, E. R. Homer

Faculty Publications

This work was supported primarily by the MRSEC program of the National Science Foundation under DMR-0079996. A method for the retrieval of the complete grain boundary character distribution by oblique double-sectioning is proposed. The method, which is similar to the recovery of the orientation distribution from sets of incomplete pole-figures, is efficient and provides many advantages as compared to calibrated serial sectioning. As compared to standard stereological approaches, the new methodology retains the advantage of direct measurement of the grain boundary inclination parameters. Solutions to the fundamental equation of oblique double-sectioning are provided in the Fourier space, and some specifics …

Global Finish Curvature Matched Machining, Jianguo Wang

Theses and Dissertations

As competition grows among manufacturing companies, greater emphasis has recently been placed on product aesthetics and decreasing the product development time. This is promoting and standardizing widespread use of sculptured surface styling within product design. Therefore, industries are looking for high efficiency machining strategies for sculptured surface machining (SSM). Many researchers have produced various methods in tool path generation for SSM. Five-axis curvature matched machining (CM2) is the most efficient. With the widespread use of 5-axis mill in industries, CM2 is a better solution for improving the machining efficiency for product concept models. CM2 has very good performance for global …

Development Of Commercial Applications For Recycled Plastics Using Finite Element Analysis, Nanjunda Narasimhamurthy

Theses and Dissertations

This thesis investigates the suitability of thermo-kinetically recycled plastics for use in commercial product applications using finite element analysis and statistics. Different recycled material blends were tested and evaluated for their use in commercial product applications. There are six different blends of thermo-kinetically recycled plastics used for testing and CATIA is used for finite element analysis. The different types of thermo-kinetically recycled plastics blends are: pop bottles made of PolyethyleneTeraphthalate (PET), milk jugs made of High-Density Polyethylene (HDPE), Vinyl seats made of Poly Vinyl Chloride (PVC) and small amount of Polypropylene (PP) and Urethane, electronic scrap made of engineering resins …

Piezoresistive Sensing Of Bistable Micro Mechansim State, Jeffrey K. Anderson

Theses and Dissertations

The objective of this work is to demonstrate the feasibility of on-chip sensing of bistable mechanism state using the piezoresistive properties of polysilicon, thus eliminating the need for electrical contacts. Changes in position are detected by observing changes in resistance across the mechanism. Sensing the state of bistable mechanisms is critical in their various applications. The research in this thesis advances the modeling techniques of MEMS devices which use piezoresistivity for position sensing. A fully compliant bistable micro mechanism was designed, fabricated, and tested to demonstrate the feasibility of this sensing technique. Testing results from two fabrication processes, Fairchild's SUMMiT …

Diseño De Sistema Automático De Control Y Monitoreo De Temperatura En El Proceso De Secado De Arroz, Rafael Bustamante Gómez

Ingeniería en Automatización

No abstract provided.

Evolution Of Turbine Blade Deposits In An Accelerated Deposition Facility: Roughness And Thermal Analysis, James Edward Wammack

Theses and Dissertations

During the operation of a gas turbine, ingested contaminants present in the air form deposits on the surfaces of the turbine blades. These deposits grow over time, resulting in an increasingly rough surface. This gradual increase in roughness results in several negative consequences, among which is an increase in the rate of heat transfer to the blade which shortens blade life. This thesis presents research in which deposits were evolved on three different turbine blade coupons and their evolution was studied. A trend in roughness change over time was discovered. Also, an attempt was made to find the effect of …