Engineering Commons^™

Analysis Of Loading Rate, Fiber Orientation And Material Composition Through Image Processing And Digital Volume Correlation In High Performance Concrete, Aidan R. Carlson

Electronic Theses and Dissertations

Ultra High Performance Concrete (UHPC) and High Performance concrete (HPC) is characterized by high compressive strength and high toughness. This is achieved through maximizing the particle packing density in the matrix and the use of fibers to reinforce the matrix, increasing the materials toughness. The interactions of fibers and the matrix during loading is quite complex and involves several different energy dissipation mechanisms. The goal of this work and this thesis is to investigate these interactions and identify any changes in material response, and hope that these changes may be useful for the design of UHPC moving forward.

In this …

Advances In Cellulose Nanomaterial-Based Foams For Environmental Applications, Md Musfiqur Rahman

Electronic Theses and Dissertations

The use of metal-oxide nanoparticles adsorbents is limited to fixed-bed columns in industrial-scale water treatment applications. This limitation is commonly attributed to the tendency of nanoparticles to aggregate, the use of non-sustainable and inefficient polymeric resins as supporting materials, or a lack of adsorption capacity. Foams and aerogels derived from cellulose nanomaterials have unique characteristics, such as high porosity and low density, which enables their use in a variety of environmental applications, including water treatment. However, the overall use of cellulose nanomaterial-based foams in various environmental sectors is limited due to the high cost of production associated with time- and …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

Thermo-Mechanical Instabilities In Next-Generation Friction Materials In High-Speed Sliding Systems, Kingsford Koranteng

Electronic Theses and Dissertations

For centuries, the manufacturing industry has incorporated metals like copper into friction materials to enhance thermal properties and minimize thermo-mechanical instabilities (TMI) in high-speed sliding systems. Unfortunately, these metals have adverse environmental effects due to the emission of hazardous particulate matter. As a result, there is a growing movement towards adopting next-generation friction materials as an alternative solution.

The study begins by conducting experimental and numerical investigations to examine the instabilities found in metal-based friction materials. The primary objective is to utilize the insights gained from the investigations to computationally explore effective strategies for mitigating various instabilities that may arise …

Molecular Dynamics Study Of Characterization In Metal-Free Friction Materials, Yizhan Zhang

Electronic Theses and Dissertations

Metallic friction materials currently used in industry may adversely impact the environment. Substitutions for metals in friction materials, on the other hand, can introduce operational safety issues and other unforeseeable issues such as thermal-mechanical instabilities and insufficient strength. In view of it, this dissertation focuses on developing different kinds of materials from simple structure to complex structure and evaluating the material properties with the assistance of molecular dynamics (MD) tools at the nano scale.

First, the concept of the contacted surfaces in friction at the atomic scale was introduced in order to get accurate understanding of the friction process compared …

Quantitative, Photocurrent Multidimensional Coherent Spectroscopy, Adam Halaoui

Electronic Theses and Dissertations

Multidimensional coherent spectroscopy (MDCS) is a quickly growing field that has a lot of advantages over more conventional forms of spectroscopy. These advantages all come from the fact that MDCS allows us to get time resolved correlated emission and absorption spectra using very precisely chosen interactions between the density matrix and the excitation laser. MDCS spectra gives the researcher a lot of information that can be extracted purely through qualitative analysis. This is possible because state couplings are entirely separated on the spectra, and once we know how to read the data, we can see how carriers transport in the …

Investigating The Effect Of Bead Geometry On Fiber Orientation And Thermomechanical Properties For Large-Format Extrusion-Based Additive Manufacturing, Joanna F. Keaton

Electronic Theses and Dissertations

In large-format extrusion-based additive manufacturing of polymer composites, the relationship between material properties and processing parameters requires further investigation. This thesis focuses on the relationship between fiber orientation and thermomechanical properties for short fiber-filled thermoplastic polymer systems manufactured by extrusion-based additive manufacturing. Fiber orientation is particularly important in determining the thermomechanical properties of the composite material as properties in the direction of deposition are expected to be higher for highly aligned fibers than randomly aligned fibers. Fiber orientation distribution, which is related to processing parameters and deposition conditions, can be efficiently represented by the orientation tensor. The orientation tensor can …

Mechanical Characterization Of Automated Fiber Placement And Additive Manufacturing Hybrid Composites, Lucan Haviland

Electronic Theses and Dissertations

This thesis presents the optimization of processing parameters based on the mechanical properties of Continuous Fiber-Reinforced Thermoplastic (CFRTP) Unidirectional (UD) consolidated tapes. The UD tapes were consolidated using an AFP head and a thermoforming press for comparison. The adhesive strength of hybrid parts consisting of CFRTP UD tape bonded to a 3D-printed substrate with the same matrix system were investigated. Large Area Additive Manufacturing (LAAM) was utilized for the 3D-printed parts. Different types of thermoplastic composite materials were explored, including Glass Fiber reinforced Polyethylene Terephthalate Glycol (GF/PETG), Carbon Fiber reinforced Polyethylene Terephthalate Glycol (CF/PETG), Carbon Fiber reinforced Polycarbonate (CF/PC), and …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Strategies To Improve The Electrochemical Performance Of Aluminum Anodes In Primary Alkaline Aluminum-Air Batteries, Razieh Kiani Harchegani

Electronic Theses and Dissertations

Passivation layers and self-corrosion developed on the Aluminum anodes in alkaline Aluminum-air batteries can significantly reduce the widespread application and capacity density of the batteries. Most corrosion prevention techniques focus on changing the electrode and electrolyte, including electrode alloying, additives for the electrolyte, and nonaqueous electrolytes. This thesis concentrates on some novel approaches like application of ultrasonic waves, as well as cold working to prevent the formation of passivation layers and hydrogen evolution. Furthermore, a conventional strategy of adding different inhibitors, including cerium chloride, a hybrid inhibitor of sodium vanadate and nanoclay is investigated. Experimental analyses were performed using ultrasonication …

Thermal, Magnetic, And Electrical Properties Of Thin Films And Nanostructures: From Magnetic Insulators To Organic Thermoelectrics, Michael J. M. Roos

Electronic Theses and Dissertations

Modern fabrication and growth techniques allow for the development of increasingly smaller and more complex solid state structures, the characterization of which require highly specialized measurement platforms. In this dissertation I present the development of techniques and instrumentation used in magnetic, thermal, and electrical property measurements of thin films and nanostructures. The understanding of trapped-flux induced artifacts in SQUID magnetometry of large paramagnetic substrates allows for the resolution of increasingly small moments. Using these methods, the antiferromagnetic coupling of the interface between a Y₃Fe₅O₁₂ film and Gd₃Ga₅O₁₂substrate is quantitatively …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Efficient Sintering Of Lunar Soil Using Concentrated Sunlight, Diprajit Biswas

Electronic Theses and Dissertations

Construction material is one crucial need for long-term habitation on the moon. When concentrated for high heat flux, solar radiation can heat lunar soil or regolith until it sinters at temperatures above 900°C. The solid, sintered soil simulant can be used as construction material. This work explores the conditions leading to effective lunar soil sintering for both direct and indirect irradiated sintering. Lunar soil simulants were sintered using concentrated light from a xenon-arc lamp with varying heat flux intensity. During direct sintering of LHS-1, a sintering range of 860°C-1140°C corresponding to a peak heat flux of 105-120 kW/m2 was identified …

Mechanics And Mechanisms Of Fracture For An Eastern Spruce Subject To Transverse Loading Using Acoustic Emission, Parinaz Belalpour Dastjerdi

Electronic Theses and Dissertations

Due to its excellent structural qualities and accessibility, wood is among the most often utilized structural materials. Despite its ubiquity, wood poses numerous challenges. It is heterogeneous and anisotropic. It has a complex hierarchical ultrastructure, and the properties can have wide variation within a species, and indeed within an individual tree. This work aims to improve our understanding of the strength and fracture behavior of spruce-pine-fir (south) (SPFs), particularly in cross-grain direction. This study’s primary goal is to examine the relationship between crack propagation and cross grain morphology under the following loading configurations: compact tension, compression, and rolling shear. The …

Influence Of Platinum Nanoparticles On Ionic Transport And Hydrogen Reactivity Of Yttria-Stabilized Zirconia Thin Films, Firas Mahyob

Electronic Theses and Dissertations

Yttria-stabilized zirconia (YSZ) is a widely used ceramic material in solid oxide fuel cells, oxygen sensors, and sensing applications due to its high ionic conductivity, chemical inertness, and thermal stability. YSZ is promising active coating for use in miniaturized harsh environment wireless surface acoustic sensors to monitor gases such as H₂. Adding catalytic Pt nanoparticles can enhance gas reactivity and lead to associated film conductivity changes.

In this work, thin films with an (8% Y₂O₃ - 92% ZrO₂) composition were deposited onto piezoelectric langasite substrates using RF magnetron sputtering in Ar:O₂ - …

Super P-Sulfur Cathodes For Quasi-Solid-State Lithium-Sulfur-Batteries., Milinda Bharatha Kalutara Koralalage

Electronic Theses and Dissertations

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Investigation Of Light Management Strategies And Photochemistry Of Si/Tio2 Tandem Microwire Slurries For Solar Hydrogen Generation., Saumya Gulati

Electronic Theses and Dissertations

The intermittent nature of the Sun makes it difficult to use it as a primary source of electricity and often needs to be supplemented by electricity from the grid which comes from fossil fuels. This motivates the need for solar energy storage. Photoelectrochemical (PEC) water-splitting has been explored as a means to convert solar energy into hydrogen (and oxygen), which can be stored as fuel. The current method of coupling PV and electrolyzer units has been widely commercialized, however, the cost of H₂ generated is far from the target of $1/kg set by the DOE under the Energy EarthShot …

Development Of Corn Kernel-Based Biocomposite Films For Food Packaging Applications, Swastika Bera

Electronic Theses and Dissertations

Most of the current and active food packaging resources and methods are nonbiodegradable and nonrenewable therefore harmful to the environment. Due to this, alternate sources of food packaging materials are in high demand. In this study, a bio-composite film has been developed, with Corn kernel powder as fiber reinforcement which is mixed with gelatin, and lignin two biopolymers as the matrix. The effect of Corn Kernel (CK) reinforcement on the Gelatin/Lignin (G/L) matrix on mechanical and barrier properties has been studied. CK has shown great potential as reinforcement to natural polymer, gelatin, and lignin (G/L) for food packaging applications as …

Design And Fabrication Of A High-Performance Heat Exchanger Using An Optimized Three-Dimensional Surface Structure Through Additive Manufacturing, Seth T. Waters

Electronic Theses and Dissertations

A heat exchanger is a device used to transfer thermal energy between two intertwining fluid pathways. In this study, the design of a novel heat exchanger is proposed using functional gradient double gyroid structure. The complex internal geometries of the gyroid structure significantly increases the surface area to volume ratio, and potentially could expressively improve efficiency of the heat transfer. The proposed idea provides a new approach for the design of a high-efficiency heat exchanger. In order to fabricate the complex structured heat exchanger system additive manufacturing is adapted instead of traditionally subtractive manufacturing techniques or casting. The prototypes of …

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

Electronic Theses and Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …

Wet Chemical Synthesis And Properties Of Argyrodite Sulfide Solid Electrolytes For Solid State Lithium Batteries., William Arnold

Electronic Theses and Dissertations

The commercialization of the lithium-ion battery (LIB) in 1991 was responsible for the explosion in portable electronic technologies that has been seen over the past 30 years. With the advent of electric vehicles and other high-powered technologies, there is tremendous demand for LIBs with higher energy density and high safety. To achieve this, new electrode materials must be explored. The obvious choice of anode material would be pure metal lithium, which has a theoretical specific capacity of 3860 mAh g^-1 . Unfortunately, metal lithium anodes have not been widely commercialized due to their tendency to react violently with the …

Biobased Packaging Materials From Cellulose Nanofibrils Produced From Virgin Wood Pulp Or Recycled Cardboard Pulp, Md Ikramul Hasan

Electronic Theses and Dissertations

Self-standing cellulose nanofibril (CNF) films are regarded as one of the promising alternatives to current petroleum-based packaging materials. The mechanical and barrier properties of CNF films are not yet up to the mark for certain applications, especially at high relative humidity. Those properties of CNF films can be tuned by the drying methods of films, degree of fibrillation, cross-linking, and controlled shrinkage. A comprehensive understanding of these processes and their influence on the structure and properties of CNF films have been presented in this thesis.

First, we prepared CNF films from CNF suspensions with two different degrees of fibrillation- standard …

Contact Dewatering Of Cellulose Nanofibers For Biopolymer Composite Applications, Alexander Collins

Electronic Theses and Dissertations

Cellulose Nanofibrils (CNFs) are promising materials for reinforcement of polymer matrices attributable to their impressive physical and mechanical properties, as well as their biodegradability. However, the utilization of these materials in composites is made challenging by the water content of CNF slurries, the tendency of CNFs to agglomerate as they dry, and incompatibility between hydrophilic CNFs and hydrophobic polymer matrices. The most commercially viable drying methods to produce small-scale dry CNFs, such as spray drying, are very energy intensive, can only dry the materials down to micron-scale agglomerates, and do not preserve fibrillar aspect ratios. “Contact dewatering,” or the removal …

Numerical Modeling Of Localized Heating In Continuous Fiber Reinforced Thermoplastic Laminates, James T. Gayton

Electronic Theses and Dissertations

The manufacturing of continuous fiber-reinforced thermoplastic (CFRTP) laminates requires the application of heat and pressure. Standard CFRTP manufacturing methods like thermoforming take a global approach to manufacturing, where the whole part is heated and undergoes a forming process. There is an opportunity to develop advanced manufacturing methods based on localized heating and deformations of consolidated stock. This thesis provides a localized heating method via networks of resistive heating elements embedded within the laminate and a means to evaluate that method.

Typical heating methods for CFRTP laminates include infrared and convective ovens or surface contact heaters. They have the same drawbacks …

Continuous, Non-Destructive Detection Of Surface Bacterial Growth With Bioinspired Vascularized Polymers, Brandon Dixon

Electronic Theses and Dissertations

Reducing or eliminating bacteria on surfaces is vital for medical devices, drinking water quality, and industrial processes. Evaluating surface bacterial growth at buried interfaces can be problematic due to the time-consuming disassembly process required for obtaining standard surface samples. In this work, a continuous, non-destructive, and reusable method was developed to detect surface bacterial growth at buried interfaces. Inspired by vascular systems in nature that permit chemical communication between the surface and underlying tissues of an organism, bacterial-specific signals diffusing from cells on the surface were detected in channels filled with an inert carrier fluid embedded in a polymer matrix. …

Comparative Life Cycle Assessment Of Embodied Carbon And Operational Energy Of Different Building Systems, Marilia Hellmeister

Electronic Theses and Dissertations

Due to human activity, the levels of carbon emissions found in the atmosphere have reached its highest concentration and therefore it is necessary to find solutions to reduce, mitigate and adapt to a more sustainable pattern of development. The substitution of fossil fuel-dependent materials with renewable materials which exhibit lower embodied carbon is an option to be considered in the design phase of a building. Engineered wood product innovations over the past twenty years, coupled with design innovation and building code modifications have demonstrated their viability in multi-story construction (18 stories). The goals of this project are to 1) estimate …

Yield And Mechanical Properties Of Veneer From Maine-Grown Eastern Spruce And Balsam Fir, Marshal Bertrand

Electronic Theses and Dissertations

This research focused on the utilization of Maine Eastern spruce and balsam fir for veneer production. Maine currently has no manufacturers of or products using structural veneer. The diversification of markets for Maine’s softwoods has been identified as a route to increase the resilience of the forest-based economy. Veneer production technology has improved significantly since the last look at Maine spruce veneer (1969), justifying the reinvestigation of Maine spruce-fir veneer. The objective of this research was to provide information on the yield of processing veneer and the quality of said veneer. A sample size of 37 Eastern spruce and 38 …

Development And Characterization Of Bound Metal Deposition Including Laser Ablation, Alexander J. Watson

Electronic Theses and Dissertations

Bound Metal Deposition (BMD) is a novel metal additive manufacturing technology in which a metal powder-binder composite paste is layer-wise extruded to form a part, which is then debound and sintered into a solid metal part. Although promising, BMD suffers from shrinkage-induced warpage and an inability to produce fine length scale features. This research addresses these problems by: (1) characterizing warpage of planar parts, and (2) developing a novel laser ablated process to create fine length scale features. First, a 12-factor resolution IV fractional-factorial design of experiments (DOE) was conducted to determine the warpage of planar parts as a function …

Development And Evaluation Of Modeling Approaches For Extrusion-Based Additive Manufacturing Of Thermoplastics, Christopher C. Bock

Electronic Theses and Dissertations

This work focuses on evaluating different modeling approaches and model parameters for thermoplastic AM, with the goal of informing more efficient and effective modeling approaches. First, different modeling approaches were tested and compared to experiments. From this it was found that all three of the modeling approaches provide comparable results and provide similar results to experiments. Then one of the modeling approaches was tested on large scale geometries, and it was found that the model results matched experiments closely. Then the effect of different material properties was evaluated, this was done by performing a fractional factorial design of experiments where …