Digital Commons Network^™

Nuclear Structure Of 186Re, David A. Matters

Theses and Dissertations

The unstable odd-Z, odd-N isotope ¹⁸⁶Re exists in a mid-shell deformed region of the chart of the nuclides where long-lived nuclear isomers are common. ¹⁸⁶Re (ground-state half-life T_1/2 = 3.7186 d) has an isomer with a half-life of ~2.0 x10⁵ y. The ^186mRe isomer is a candidate energy-storage medium for a radioisotope power source of military importance that would operate on the principle of isomer depletion. Data about levels and transitions above the ^186mRe isomer, absent from the adopted level scheme for ¹⁸⁶Re, are needed to identify a means of depleting the isomer. …

Improvements To Micro-Contact Performance And Reliability, Tod V. Laurvick

Theses and Dissertations

Microelectromechanical Systems (MEMS) based devices, and specifically microswitches, continue to offer many advantages over competing technologies. To realize the benefits of micro-switches, improvements must be made to address performance and reliability shortfalls which have long been an issue with this application. To improve the performance of these devices, the micro-contacts used in this technology must be understood to allow for design improvements, and offer a means for testing to validate this technology and determine when such improvements are ready for operational environments. To build devices which are more robust and capable of continued operation after billions of cycles requires that …

Analysis Of Small Muscle Movement Effects On Eeg Signals, Erhan E. Yanteri

Theses and Dissertations

In this thesis, the artefactual effects of the small muscle movements were investigated. Upper frequency bands (30 Hz) of the EEG signal were extracted in order to investigate the artefactual effects of the small muscle movements. When the contamination level is high, the detection of the small muscle artifact can be made with the 92.2% accuracy. If these artifacts are really small such as a single finger movement, the detection accuracy decreases to 64%. But, the detection accuracy increases to 72% after removing the eye blink artifacts. The results of the classification support our hypothesis about the artefactual effects of …

Reflection Matrix Method For Controlling Light After Reflection From A Diffuse Scattering Surface, Kenneth W. Burgi

Theses and Dissertations

This research focuses on reflective inverse diffusion, which was a proof-of-concept experiment that used phase modulation to shape the wavefront of a laser causing it to refocus after reflection from a rough surface. By refocusing the light, reflective inverse diffusion has the potential to eliminate the complex radiometric model of indirect photography by creating a virtual light source at the first diffuse reflector that satisfies the line-of-sight requirement of dual photography. However, the initial reflective inverse diffusion experiments provided no mathematical background and were conducted under the premise that the process operated similarly to transmissive inverse diffusion.

In this research, …

Integrated Circuit Wear-Out Prediction And Recycling Detection Using Radio-Frequency Distinct Native Attribute Features, Randall D. Deppensmith

Theses and Dissertations

Radio Frequency Distinct Native Attribute (RF-DNA) has shown promise for detecting differences in Integrated Circuits(IC) using features extracted from a devices Unintentional Radio Emissions (URE). This ability of RF-DNA relies upon process variation imparted to a semiconductor device during manufacturing. However, internal components in modern ICs electronically age and wear out over their operational lifetime. RF-DNA techniques are adopted from prior work and applied to MSP430 URE to address the following research goals: 1) Does device wear-out impact RF-DNA device discriminability?, 2) Can device age be continuously estimated by monitoring changes in RF-DNA features?, and 3) Can device age state …

Kinetics Of Graphite Oxidation In Reacting Flow From Imaging Fourier Transform Spectroscopy, Ashley E. Gonzales

Theses and Dissertations

This work focuses on the characterization of laser irradiated graphite oxidation using mid-wave infrared (MWIR) imaging Fourier transform spectroscopy (IFTS). Although graphite oxidation has been studied extensively, IFTS uniquely provides spatial characterization of the reacting plumes. Spatial maps of species and temperature provide much needed insight into the transport and kinetic mechanisms and are vital for validation of numerical efforts. The current study builds on previous work using IFTS to characterize graphite oxidation in buoyant flow. Buoyant flow measurements are expanded to a wider range of graphite materials and surface temperatures. Oxidation in flat plate shear flow and stagnation flow …

Passively Estimating Index Of Refraction For Specular Reflectors Using Polarimetric Hyperspectral Imaging, Jacob A. Martin

Theses and Dissertations

As off-nadir viewing platforms becoming increasingly prevalent in remote sensing, material classification and ID techniques robust to changing viewing geometries must be developed. Traditionally, either reflectivity or emissivity are used for classification, but these quantities vary with viewing angle. Instead, estimating index of refraction may be advantageous as it is invariant with respect to viewing geometry. This work focuses on estimating index of refraction from LWIR (875-1250 wavenumbers) polarimetric hyperspectral radiance measurements.

Spacex: Breaking The Barrier To The Space Launch Vehicle Industry, Matthew M. Liskowcyz

Theses and Dissertations

The Space Launch Vehicle (SLV) industry has been around for a long time, but few companies have managed to enter this industry. SpaceX was founded only 10 years ago, but it has managed to become a leader in the U.S. industry and a dominant player worldwide. The purpose of this thesis research is to discover what it took for SpaceX to break into this tightly controlled industry. A qualitative analysis was performed to compare SpaceX to companies that overcame the barriers of entry for their respective industries. SpaceX, like FedEx, could implement a unique technique to the industry and find …

An Information Theoretic Investigation Of Complex Adaptive Supply Networks With Organizational Topologies, Joshua V. Rodewald

Theses and Dissertations

Supply networks exist throughout society in manufacturing and knowledge-intensive industries as well as many service industries. Organizations have been noted to behave as complex adaptive systems or information supply networks with both formal and informal structures. Thoroughly understanding supply network structure and behavior are critical to managing such organizations effectively, but their properties of complex adaptive systems make them more difficult to analyze and assess, forcing researchers to rely on unrealistic data or assumptions of behavior. This research proposes an information theoretic methodology to discover such complex network structures and dynamics while overcoming the difficulties historically associated with their study. …

Flow Field Dynamics In A High-G Ultra-Compact Combustor, Andrew E. Cottle

Theses and Dissertations

The Ultra Compact Combustor (UCC) presents a novel solution to the advancement of aircraft gas turbine engine performance. A high-g UCC design operates by diverting a portion of the axial compressor flow into a circumferential combustion cavity positioned about the engine outer diameter. The circumferential cavity (CC) provides the necessary residence length and time for combustion within reduced axial lengths; furthermore, high rates of centrifugal acceleration termed high-g loading are imposed upon the swirling cavity flow. These high-g conditions are hypothesized to increase flame speed, reduce flame length, and improve lean blow-out performance. Work at AFIT was sponsored by the …

Simulation Of Aircraft Sortie Generation Under An Autonomic Logistics System, Gunduz Bingol

Theses and Dissertations

Parallel to the developments in diagnostic and prognostic technology, autonomic logistics systems (ALS) have been a potential improvement for the aircraft sortie generation process. Currently, Lockheed Martin and the Joint Program Office are developing a new autonomic logistics system for the multibillion F-35 Lightning Joint Strike Fighter project, which is named the Autonomic Logistics Information System (ALIS). Generally, researchers make an analogy between the ALS and the human bodys autonomic nervous system since both of them monitor, control, and adjust autonomic responses to external stimuli. Based on this perspective, ALS aims to switch the Air Force logistics mentality from a …

Degradation Of Carbon Fiber Reinforced Polymer And Graphite By Laser Heating, Nicholas C. Herr

Theses and Dissertations

The availability of high power, diode pumped solid state and fiber lasers at powers 10 kW and shorter wavelengths (1.07 micrometer) has invigorated the development of tactical laser weapons. This shift to tactical missions greatly increases the variety of potential targets including carbon fiber reinforced polymers and related materials. The complexity of laser-material interactions has driven a historical reliance on live-fire testing and empirical models, but this becomes more difficult as the number of target materials grow. This dissertation combines thermal imagery and existing thermal models of the fire response of composite materials to develop a hybrid modeling approach of …

Air Force Project Risk Management – The Impact Of Inconsistent Processes, Eric J. Perez

Theses and Dissertations

On the surface, the majority of Air Force units appear to be executing some form of project risk management (PRM). Deeper investigation exposes many of the PRM practices currently in place to often be ad hoc, and as such, have the potential to poorly inform decisions when risk data is escalated to the enterprise levels of the Air Force. Resultantly, there is inconsistency between the PRM processes practiced by Air Force units. This inconsistency is an indication of risk mishandling at the project level and erroneous risk data provided at the enterprise levels of the Air Force. It may be …

Effect Of Stress Ratio On Fatigue Crack Growth Rate At Notched Hole In 7075-T6 Aluminum Alloy Under Biaxial Fatigue, Reja Alshahrani

Theses and Dissertations

This research investigates the behavior of fatigue crack growth rate in both laboratory air and saltwater (3.5% NaCl) environments for notched cruciform specimen made from 7075-T6 aluminum alloy sheet at different stress ratios. With biaxility ratio of 1, and frequency of applied load of 10 Hz, the crack growth behavior was investigated under in-plane biaxial tension-tension fatigue with 0.1, 0.5, 0.7 stress ratios and then compared them to study the effect of stress ratio on the crack growth rate. Finite Element Analysis (FEA) was used to calculate cyclic variation of stress intensity factors (delta K) at the crack tips. The …

A Novel Machine Learning Classifier Based On A Qualia Modeling Agent (Qma), Sandra L. Vaughan

Theses and Dissertations

This dissertation addresses a problem found in supervised machine learning (ML) classification, that the target variable, i.e., the variable a classifier predicts, has to be identified before training begins and cannot change during training and testing. This research develops a computational agent, which overcomes this problem. The Qualia Modeling Agent (QMA) is modeled after two cognitive theories: Stanovich's tripartite framework, which proposes learning results from interactions between conscious and unconscious processes; and, the Integrated Information Theory (IIT) of Consciousness, which proposes that the fundamental structural elements of consciousness are qualia. By modeling the informational relationships of qualia, the QMA allows …

Mechanical Properties And Fatigue Behavior Of Unitized Composite Airframe Structures At Elevated Temperature, Mohamed Noomen

Theses and Dissertations

The tension-tension fatigue behavior of a newly developed unitized composite material system was investigated. The unitized composite consisted of a polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC). The PMC portion consisted of an NRPE high-temperature polyimide matrix reinforced with carbon fibers woven in an eight harness satin weave (8HSW). The CMC layer is a single-ply non-crimp 3D orthogonal weave composite consisting of ceramic matrix reinforced with glass fibers. In order to assess the performance and suitability of this composite for use in aerospace components designed to contain high-temperature environments, mechanical tests were performed under temperature conditions …

Application Of Executable Architecture In Early Concept Evaluation Using The Dod Architecture Framework, Zhongwang Chua

Theses and Dissertations

The increasing complexity in the development of today's modern warfighting systems demands a systematic evaluation approach in the assessment of the envisaged capability and estimating the cost effectiveness, especially in the early stages of Concept Development. This research focused on the development of early Concept evaluation methodology through the use of Executable Architecture (EA) through the System Architecting process. Particularly, the methodology was applied in the assessment of a proposed Multi-tiered Unmanned Aircraft System System-of-System that is designed provide target acquisition and conduct dynamic strike on Theater Ballistic Missile launchers. Through the implementation of the evaluation methodology using dynamic modeling …

Corrosion Fatigue Crack Growth Behavior At Notched Hole In 7075-T6 Under Different Biaxial Stress Ratios, Khalid A. Alghamdi

Theses and Dissertations

This thesis presents the results of a study to quantify the effects of biaxial loading on fatigue crack behavior in both air and saltwater (3.5% NaCl) environments from pre-cracked notched circular hole in a 7075-T6 cruciform specimen using a fracture mechanics approach. With stress ratio of R = 0.5, the crack growth behavior was investigated under fatigue loading with 0.5, 0, -0.5, and -1 biaxial stress ratio lambda. The crack propagation was monitored using optical microscopy. Finite Element Analysis was performed using the different stress ranges and stress ratios with various crack sizes to compute of stress intensity factors (delta …

Adaptive Estimation And Heuristic Optimization Of Nonlinear Spacecraft Attitude Dynamics, Joshuah A. Hess

Theses and Dissertations

For spacecraft conducting on-orbit operations, changes to the structure of the spacecraft are not uncommon. These planned or unanticipated changes in inertia properties couple with the spacecraft's attitude dynamics and typically require estimation. For systems with time-varying inertia parameters, multiple model adaptive estimation (MMAE) routines can be utilized for parameter and state estimates. MMAE algorithms involve constructing a bank of recursive estimators, each assuming a different hypothesis for the systems dynamics. This research has three distinct, but related, contributions to satellite attitude dynamics and estimation. In the first part of this research, MMAE routines employing parallel banks of unscented attitude …

Physical Layer Defenses Against Primary User Emulation Attacks, Joan A. Betances

Theses and Dissertations

Cognitive Radio (CR) is a promising technology that works by detecting unused parts of the spectrum and automatically reconfiguring the communication system's parameters in order to operate in the available communication channels while minimizing interference. CR enables efficient use of the Radio Frequency (RF) spectrum by generating waveforms that can coexist with existing users in licensed spectrum bands. Spectrum sensing is one of the most important components of CR systems because it provides awareness of its operating environment, as well as detecting the presence of primary (licensed) users of the spectrum.

Time Domain Analysis Of Electromagnetic Scattering From Multiple Cavities Embedded In A Ground Plane, Richard P. Uber

Theses and Dissertations

This work examines the scattered fields produced when a transient wave is reflected from an infinite perfect electric conductor (PEC) ground plane with multiple embedded cavities. Incident and reflected waves will be decomposed into transverse magnetic to the z direction (TMz) and transverse electric to the z direction (TEz) polarizations, with primary focus given to the TMz. Cavities may be unfilled, partially filled, or fully filled with non-magnetic dielectric material and no assumptions are made regarding similarity, regularity, or periodicity. The Newmark method is used to discretize time and a variational formulation is presented for each time step. The principle …

A Statistical Approach To Characterize And Detect Degradation Within The Barabasi-Albert Network, Mohd-Fairul Mohd-Zaid

Theses and Dissertations

Social Network Analysis (SNA) is widely used by the intelligence community when analyzing the relationships between individuals within groups of interest. Hence, any tools that can be quantitatively shown to help improve the analyses are advantageous for the intelligence community. To date, there have been no methods developed to characterize a real world network as a Barabasi-Albert network which is a type of network with properties contained in many real-world networks. In this research, two newly developed statistical tests using the degree distribution and the L-moments of the degree distribution are proposed with application to classifying networks and detecting degradation …

Data Driven Device Failure Prediction, Paul L. Jordan

Theses and Dissertations

As society becomes more dependent upon computer systems to perform increasingly critical tasks, ensuring those systems do not fail also becomes more important. Many organizations depend heavily on desktop computers for day to day operations. Unfortunately, the software that runs on these computers is still written by humans and as such, is still subject to human error and consequent failure. A natural solution is to use statistical machine learning to predict failure. However, since failure is still a relatively rare event, obtaining labeled training data to train these models is not trivial. This work presents new simulated fault loads with …

Applying Lean To The Ac-130 Maintenance Process For The Royal Saudi Air Force, Fisal A. Alzahrani

Theses and Dissertations

The ideas expressed in this research come from the researchers experiences working in the AC-130 maintenance squadron in the Royal Saudi Air Force. The AC-130 maintenance process is not currently being used as effectively as it could be to make AC-130 fully mission capable. That can be done by improving communication, reducing distances needed to move or transport anything during the maintenance process and by efficient use of the available qualified workforces, tools and equipment. Consideration is given to applying an existing management technique to the Royal Saudi Air Forces AC-130 Maintenance Squadrons. The selected technique is the Lean management …

Improving Real-World Performance Of Vision Aided Navigation In A Flight Environment, Donald T. Venable

Theses and Dissertations

The motivation of this research is to fuse information from an airborne imaging sensor with information extracted from satellite imagery in order to provide accurate position when GPS is unavailable for an extended duration. A corpus of existing geo-referenced satellite imagery is used to create a key point database. A novel algorithm for recovering coarse pose using by comparing key points extracted from the airborne imagery to the reference database is developed. This coarse position is used to bootstrap a local-area geo-registration algorithm, which provides GPS-level position estimates. This research derives optimizations for existing local-area methods for operation in flight …

Optical Theory Improvements To Space Domain Awareness, Tyler J. Hardy

Theses and Dissertations

This dissertation focuses on increasing the ability to detect space objects and increase Space Domain Awareness (SDA) with space surveillance sensors through image processing and optical theory. SDA observations are collected through ground-based radar and optical systems as well as space based assets. This research focuses on a ground-based optical telescope system, the Space Surveillance Telescope (SST). By increasing the number of detectable Resident Space Objects (RSOs) through image processing, SDA capabilities can be expanded. This is accomplished through addressing two main degrading factors present in typical SDA sensors; spatial undersampling in the collected data and noise models and assumptions …

Space Qualification Testing Of A Deployable Shape Memory Alloy Cubesat Antenna, Carl L. Kobza

Theses and Dissertations

Increasingly capable CubeSat missions require antenna with improved Radio Frequency performance over the traditional CubeSat antennas. Deployable quadrifilar helical antennas (QHA) enable an acceptable stowing volume and deploy to provide increased gain and bandwidth over traditional patch and dipole antennas. Extensive ground testing is required to ensure the antenna is space qualified and to characterize the antenna deployment in the space environment. AFIT requires a QHA to perform a future CubeSat geolocation mission and contracted Helical Communication Technologies (HCT) to design and manufacture a Shape Memory Alloy (SMA) L-band deployable QHA. Vibration, thermal vacuum, laser vibrometer, and Voltage Standing Wave …

Evaluation Of The Impact Of An Additive Manufacturing Enhanced Cubesat Architecture On The Cubesat Development Process, Rachel E. Sharples

Theses and Dissertations

Additive manufacturing (AM) is a fabrication method ideally suited to low-quantity, highly customized builds, leading to interest in its application to satellite development and manufacturing, where each build is unique. Due to the issues of long development schedules and high development and manufacturing costs, methods are needed in the CubeSat development process to reduce the weight and volume of subsystems and decrease integration time. The work develops an architecture for an AM-augmented CubeSat and examines the AM techniques of embedded electronics, embedded thrusters, and custom radiation-hardened materials can impact the subsystems of a CubeSat. The AM-augmented architecture shows a shift …

A Temporal Framework For Hypergame Analysis Of Cyber Physical Systems In Contested Environments, Nicholas S. Kovach

Theses and Dissertations

Game theory is used to model conflicts between one or more players over resources. It offers players a way to reason, allowing rationale for selecting strategies that avoid the worst outcome. Game theory lacks the ability to incorporate advantages one player may have over another player. A meta-game, known as a hypergame, occurs when one player does not know or fully understand all the strategies of a game. Hypergame theory builds upon the utility of game theory by allowing a player to outmaneuver an opponent, thus obtaining a more preferred outcome with higher utility. Recent work in hypergame theory has …

Optimal Control Of An Uninhabited Loyal Wingman, Clay J. Humphreys

Theses and Dissertations

As researchers strive to achieve autonomy in systems, many believe the goal is not that machines should attain full autonomy, but rather to obtain the right level of autonomy for an appropriate man-machine interaction. A common phrase for this interaction is manned-unmanned teaming (MUM-T), a subset of which, for unmanned aerial vehicles, is the concept of the loyal wingman. This work demonstrates the use of optimal control and stochastic estimation techniques as an autonomous near real-time dynamic route planner for the DoD concept of the loyal wingman. First, the optimal control problem is formulated for a static threat environment and …